Siemens SP-36 Wartungs- und Serviceanleitung

Installation &

Maintenance

Power Line Surge

Protector

Model

-36

INTRODUCTION

The

SP-36

is a

secondary

surge

protector designed

to be

mounted

on a

load

center at the

power

service

entrance.

It offers

power-line protectors

and is

easi

wired into existing

systems

has

exposed

erm

inals

INSTALLATION

The SP-36 must be

mounted horizontally

shown

•Never mount the SP-36

ver

The

arrestors

may not

"clear" properly

mounted

in the vertical

position.

•The SP-36 should never be

mounted

with

the

vent holes

obstructe

•This unit is only for use

areas

protected

from

the

weather,

such as inside a

bungalow

equipment case.

•Never install on the "line" side of a

branch breaker

on a

load center.

Siemens Industry, Inc., Rail Automation

2400 Nelson Pkwy.,Louisville KY

WHITE

022701-29X

BLACK

022701-29X

BLACK

I&M 010836-6

Revised 11/95, 6/00, 8/14

Doc. No.: SIG-00-00-10 Version A.1

Doc. No:

Version:

PROCEDURES

WARNING

HIGH VOLTAGES ARE PRESENT. TURN

OFF

POWER

BEFORE INSTALLATION OR

SERVICING.

The use of temporary ground during installation and maintenance is

recommended

1) Install one washer over the threads at the end of the SP-36 housing. Push the washer

against the

housing.

2) Choose a knockout in the load center that is a distance from the backboard that

will

allow the back of the SP-36 to lay flat against the

backboard.

3) Install the second washer on the threads at the end of the SP-36 housing from

inside

the load

center

Install the lock nut so that it loosely holds the SP-36 in

place.

4) Use the wood screw provided to secure the SP-36 mounting tab to the

backboard

5) Tighten the lock nut installed in step 3 for a snug

fit.

Cut the wires on the SP-36 to the minimum usable

lengt

Do not coil the wires as

this

greatly reduces SP-36

performanc

Also,

avoid kinks and sharp bends in the

wiring

7) Connect the wires to the load center, observing the proper hook-up

scheme.

8) The wires must be connected so that there is a fuse or circuit breaker between the

SP-

and the power service

line.

HOOK UP

SCHEMES

Doc. No:

Version:

MAINTENANCE

The SP-36 requires no regular maintenance. Over time, with repeated surges, the

power-line

protectors inside will become damaged. They can be inspected visually through the clear

plastic

housing and, if blackened or burned, should be replaced as described

below

CAUTION

DO NOT INSERT ANY OBJECTS INTO THE VENT

HOLES OF THE

SP-36.

SERVICING

The power-line protectors can be replaced as

follows:

1) Turn off all power to the load center at the main breaker. Make sure power is

off.

2) Disconnect the SP-36 wires from the load

center

3) Remove the two screws holding the cover on the

SP-36

4) Remove the nuts holding the protectors in place and remove the

protectors.

5) Install the new

protectors.

6) Reinstall nuts removed in step 4 and tighten nuts to hold the new protectors in

place.

7) Reinstall the cover and secure with the screws removed in step

8) Reconnect the SP-36 wires to the load

center-

observe correct

hookup.

9) Restore power to the load

center.

REPLACEMENT

PARTS

To Order: Specify Description and Part

Number

tem

Part

No.

Descr

tion

Qty.

010836-1

Protector

ousing

022312-11-6X

Wire 12

Ga.

Black x 18"

w/Term

022312-18-1X

Wire 12 Ga. W

x 24" w/Termina

010836-5

Rubber Grommet Bushing

022701

29X Power Line Protector w/o Ca

23839-25

Buss Connector

023690-14A

Beveled

Washer

3690

-14

ClampNut

010836-2

Box

Cover

5283

Tap Screw

#8 x

1/2

010836-

Name Plate

010836-4

Warning

Label

7152

Lock Nut

1760

Flat Washer 1 x 2-1

5722-RSC

Wood Screw RD #10 x

1-1

Inhaltsverzeichnis

Andere Siemens Überspannungsschutz Handbücher

Siemens

Siemens 3TX6446-1 Series Bedienungsanleitung

Siemens

Siemens TPSA9040 Bedienungsanleitung

Siemens

Siemens 5SD7483-6RC Bedienungsanleitung

Siemens

Siemens 3TX7402-3A Bedienungsanleitung

Siemens

Siemens SPD4home Bedienungsanleitung

Siemens

Siemens 5SD7463-0 Bedienungsanleitung

Siemens

Siemens 5SD7483-5 Bedienungsanleitung

Siemens

Siemens BSPD 100 Series Bedienungsanleitung

Siemens

Siemens TPS3 09 Bedienungsanleitung

Siemens

Siemens FireSeeker FS-100 Bedienungsanleitung

Siemens

Siemens TPS3 Bedienungsanleitung

Siemens

Siemens 5SD7442-1 Bedienungsanleitung

Siemens

Siemens 5SD7 413-2 Bedienungsanleitung

Siemens

Siemens 5SD7418 Series Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Siemens

Siemens SPD4tel Bedienungsanleitung

Siemens

Siemens 5SD7444-1 Bedienungsanleitung

Siemens

Siemens 5SD7483-5 Bedienungsanleitung

Siemens

Siemens SP-37 Wartungs- und Serviceanleitung

Siemens

Siemens 3TX7462-3 Bedienungsanleitung

Siemens

Siemens TPS3 03 Bedienungsanleitung

Siemens

Siemens 5SD7434-1 Bedienungsanleitung

Siemens

Siemens TPS3 03 DC Bedienungsanleitung

Siemens

Siemens 5SD7 498-3 Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung

Intermatic

Intermatic PS3000 Bedienungsanleitung