Siemens Pointek CLS300 Benutzerhandbuch

Siemens Milltronics Process Instruments Inc.

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario

K9J 7B1 / Canada

Tel.: (705) 745-2431

Fax: (705) 741-0466

www.siemens.com/processautomation

AG080910

Pointek CLS300 Capacitance Switch (Standard Electronics Version)

Configuration of CLS300 Standard Models Manufactured After January 26, 2011

Objective: Set up and calibrate the Pointek CLS300 (Standard Electronics Version). This app guide applies to any

models manufactured after January 26, 2011.

Equipment: Pointek CLS300 (Standard Electronics Version) Capacitance Switch

While every effort was made to verify the following information, no warranty of accuracy or usability is expressed or implied.

Overview

This application guide is an addition to the operating instructions. Please review CLS300 (Standard Electronics Version) operating

instructions to ensure that the device is properly mounted.

This application guide provides a basic procedure for setting the switch point for correct operation of the CLS300 (Standard

Electronics Version) in either covered or uncovered states. Please note that the guide applies only to hardware manufact

ured after January 26, 2011 as indicated by a serial number of PBD/B127xxxx or higher. (For example, PBD/C9xxxxxx or

PBD/B128xxxx.)

Included in the guide are the appropriate start up procedures to quickly and effectively set up the Pointek CLS300 (Standard

Electronics Version) capacitance switch for general applications, demanding applications and interface detection. It also contains

instructions for adjusting the setpoint and alarm delay.

For more detailed information, please consult the operating manual (7ML19985JH04).

Adjusting the Setpoint

Before adjusting the setpoint or alarm delay the cover must be removed.

Prior to removing the cover, please ensure that power is removed, and that the application and installation allow for removal of

the cover. (This may not be permitted in some Hazardous Areas.)

Once the cover has been removed, apply power to the unit. The green power LED (L3) will glow indicating that the unit is powered

and operational. If L3 is not on, please consult the Specifications and Troubleshooting sections of the operating instructions.

APPLICATION GUIDE

Pointek CLS300 (Standard) AG080910 2 of 4

APPLICATION GUIDE

Pointek CLS300 Applications

Pointek CLS300 can be set up for three different applications which are described in the table below. Use the calibration

procedure for the application that most closely describes your operation.

Application Material Setup Conditions

General dry solids

low viscosity liquids

sensor uncovered;

min. 100 mm (4") free space all around

Demanding

hygroscopic / wet solids

high viscosity and high conductivity

liquids

sensor immersed then uncovered; but

retaining max. possible material buildup

Interface detection liquid A / liquid B

foam / liquid

immerse sensor in whichever material has

lowest dielectric constant

Calibration for general applications (Failsafe low, no delay)

1. Ensure that the green power LED (L3) is on.

2. Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).

3. Turn the delay potentiometer (P1) fully counter-clockwise.

4. Adjust the material level of the process so that the probe is uncovered with a minimum of 100 mm (4”) free space all

around.

5. If the yellow sensor status LED (L1) is on, proceed to step 6. If L1 is off, turn the trip point potentiometer (P2) counter-

clockwise until it just turns on. If the yellow LED does not turn on set DIP switch S5 to ON and repeat step 5.

trip poin

switches

L1 L3

dela

output

status

(

red

)

sensor

status

(

ellow

)

power

(green)

delay: alarm activation¹

delay: alarm deactivation¹

ailsafe/alarm¹

est delay settings

sensitivit

ROCKER DOWN

↓

hen S3 is ON, it inverts the relay function,

and the functionin

of S1 and S2.

Pointek CLS300 (Standard) AG080910 3 of 4

APPLICATION GUIDE

6. Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED (L1) just turns off.

Calibration for demanding applications (Failsafe low, no delay)

1. Ensure that the green power LED (L3) is on.

2. Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).

3. Turn the delay potentiometer (P1) fully counter-clockwise.

4. Adjust the material level of the process so that the sensor is immersed.

5. Adjust the material level of the process so that the sensor is uncovered, but retains as much buildup of material as

possible.

6. If the yellow sensor status LED (L1) is on, proceed to step 7. If L1 is off, turn the trip point potentiometer (P2) counter-

clockwise until it just turns on. If the yellow LED does not turn on set DIP switch S5 to ON and repeat step 6.

7. Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED (L1) just turns off.

Calibration for interface detection (Failsafe low, no delay)

1. Ensure that the green power LED (L3) is on.

2. Set DIP switches S1 to S5 to OFF (rocker down as shown in the diagram above).

3. Turn the delay potentiometer (P1) fully counter-clockwise.

4. Adjust the material level of the process so that the sensor is covered by the material with the lowest relative dielectric

constant.

5. If the yellow sensor status LED (L1) is on, proceed to step 6. If L1 is off, turn the trip point potentiometer (P2) counter-

clockwise until it just turns on. If the yellow LED does not turn on set DIP switch S5 to ON and repeat step 5.

6. Slowly turn the trip point potentiometer (P2) clockwise until the yellow sensor status LED (L1) just turns off.

Alarm Delay Function

If you want to slow the Pointek CLS300 response, to compensate for turbulence or false readings, set a delay interval using the

delay potentiometer (P1) and set DIP switches S1 and/or S2 to the OFF position to enable the delay for either alarm activation (S1

OFF), alarm de-activation (S2 OFF), or both (S1 and S2 OFF). (Note: This information can usually be found inside the device cover.)

Pointek CLS300 (Standard) AG080910 4 of 4

APPLICATION GUIDE

If an immediate alarm output is critical, disable the delay by setting the appropriate switch (either S1 or S2) to ON. The functioning

of switches S1 and S2 depends on the alarm setting:

S1 - ON disables delay of alarm de-activation (alarm OFF)

High alarm/

overfill protection S2 – ON disables delay of alarm activation (alarm ON)

S1 – ON disables delay of alarm activation (alarm ON)

Low alarm/

dry run protection S2 - ON disables delay of alarm de-activation (alarm OFF)

Testing the Alarm Delay

This test procedure assumes that you have completed one of the calibration processes described previously.

1. Grasp the probe with your hand. The yellow sensor status LED (L1) should turn on immediately. The red output status

LED (L2) should turn on after a delay.

2. Turn the delay potentiometer (P1) clockwise about 1/8 of a turn.

3. Turn DIP switch S4 to the ON position; this will simulate a change in state of the probe (covered/uncovered).

4. L1 (the yellow LED) should turn on immediately, and L2 (the red LED) should turn on after a longer delay than in Step 1.

5. Turn DIP switch S4 to the OFF position.

6. Continue to adjust the delay potentiometer (P1) until you have the desired delay.

Operation

After completing the setup, replace the lid and secure the lid clip. Pointek CLS300 Standard model is now ready to operate.

Andere Handbücher für Pointek CLS300

Andere Siemens Schalten Handbücher

Siemens

Siemens RUGGEDCOM RS8000H Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RS900W Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT263-1 Series Bedienungsanleitung

Siemens

Siemens SIRIUS 3SE53 2-0SH 1 Series Bedienungsanleitung

Siemens

Siemens SCALANCE XR-300WG Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RS8000A Bedienungsanleitung

Siemens

Siemens SITRANS LVL200E Bedienungsanleitung

Siemens

Siemens Sitrans LVL200 Bedienungsanleitung

Siemens

Siemens SCALANCE XF-200BA Bedienungsanleitung

Siemens

Siemens 3VW9011-0AK03 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RS900GP Bedienungsanleitung

Siemens

Siemens 3VW9011-0AT11 Bedienungsanleitung

Siemens

Siemens 3RH14-1 Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RST916C Bedienungsanleitung

Siemens

Siemens 3VF9421-1 Series Bedienungsanleitung

Siemens

Siemens SCALANCE XR-500 Bedienungsanleitung

Siemens

Siemens 3VM9988-0AB1 Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1510 Bedienungsanleitung

Siemens

Siemens RUGGEDCOM RX1511 Bedienungsanleitung

Siemens

Siemens 3VA1225-1AA.2 Bedienungsanleitung

Siemens

Siemens 3KD 6 Series Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RS900G Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RSG2200F Bedienungsanleitung

Siemens

Siemens SIMATIC NET RUGGEDCOM RS8000A Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung