Sierra Wireless Airlink Raven XE H2225E Bedienungsanleitung

Page 1of 9

Sierra Wireless Airlink Raven XE H2225E Router

Description

The target of the Airlink Raven XE is the Alarming Module. Its purpose is to Send and Receive SMS

messages. Essentially, it is going to be utilized as an SMS gateway. As an example, Ignition picks up

information from a PLC that the water temperature is too hot. Ignition send an SMS message via the

Raven XE to contacts assigned to that alarm. It is received by a contact, which is then acknowledged via

SMS by the contact. This SMS message is sent back and received by Ignition via the Raven XE.

Raven XE and Network Security

The security settings covered here are basic steps to secure the Raven XE. Inductive Automation is not

responsible for the security of your Raven XE. You should take the time to configure and test the

current and other security measures as appropriate to your network.

Inductive Automation tested this router as a device that sits inside a network. Therefore, it needs to be

configured to act simply as another device on the network, not as a router or DHCP Server etc. Its sole

purpose is to handle SMS traffic. The setup steps below cover these. If you wish to utilize its other

features, bear in mind that you will need to ensure it works properly on your network and is secure.

Configuration and ACEManager

To access and change the modem’s configuration information, you will be accessing what is called the

ACEManager. This can be accessed via Ethernet, USB or Serial. This document will only cover Ethernet

access. The recommended browser to use is IE or Firefox. ACEManager run poorly under Safari and

Chrome.

Setup Steps

The sections below should be followed in the order given to setup the Raven XE H2225E. Note that any

change that is made usually requires a reboot of the modem, which can be done through the

ACEManager. Follow these instructions and reboot at the end.

Default Ethernet Connection

First connect the Raven XE directly to your computer and follow the manual’s instructions to

connect to it.

Default Ethernet settings for access is:

Device IP Address: 192.168.13.31

Port: 9191

Username: user

Password: 12345

Page 2of 9

It should be as simple as changing your computer’s LAN settings to DHCP. Then connect to it via

a browser with http://192.168.13.31:9191/index.htm.

Password

The first thing you need to do is change the password. From the Admin Tab of ACEManager,

change it.

Firmware

The first thing to check is if the router’s firmware is up-to-date. Go to the Status Tab. If the

router’s ALEOS Software Version is H2225E_4.0.10.001 Jul 21 2011 or earlier, it should be

updated. As of this writing, the latest firmware version is H2225E_4.0.11. This can be found on

the Sierra Wireless website at

http://www.sierrawireless.com/en/Support/Downloads/AirLink/Configurable_Intelligent_Gatew

ays/AirLink_Raven_XE_HSPA_for_ATT_H2225E-C.aspx. The executable file is

RvnXE_90_H2225E_4.0.11.003.exe.

With the firmware downloaded, follow these instructions to install it:

1) Simply connect the Ethernet cable from your laptop to the router;

2) Set your computer to DHCP;

3) Double-click on the file to execute the firmware upgrade program.

4) You will be entering the IP address of 192.168.13.31 with the default username and the

appropriate password.

5) Follow the instructions on the upgrade program.

The Raven XE’s manual also covers how to upgrade the firmware easily.

Setting up the Raven to be on a network

The ACEManager will be accessed to change the LAN and other setting to enable it to be

accessed via an existing network. After the firmware upgrade, you should still be able to access

it via the default Ethernet settings.

Go to the LAN –Ethernet Tab and enter the following:

DHCP Server Mode: Disable

The Raven XE has a built-in DHCP Server. This must be disabled. If not it

may cause network issues, creating conflicts on existing IP addresses

already assigned.

Host Routing Mask: 255.255.5.0

The following is a screen shot of the default LAN settings Inductive Automation is using –you

should adjust these as appropriate to you network:

Page 3of 9

After the above has been done, go to the LAN –Host Port Routing Tab. The router must be set

to NOT act as the gateway on the network.

Primary Gateway: Disabled

Failure to make the above setting may cause devices on the network to cease functioning.

Below is a screen shot of the change:

Page 4of 9

ACEManager “Over-The-Air”

By default the ACE Manager can be accessed “over-the-air”. If you load the Inductive

Automation default configuration, it is disabled. This will add security to the device to prevent

access from outside the network.

Page 5of 9

SSH Interface to the Router

If you load the Inductive Automation default configuration, SSH is used in preference to Telnet.

To SSH into the router, use Putty or some other SSH Client. See Ethernet section for IP and login

credentials. The SSH Port number to use is 2332 by default. The following is the SSH setup page

in ACEManager:

Page 6of 9

Configuring SMS

In order to send SMS it must be enabled. Go to the Services –SMS tab. The following changes

are made:

SMS Send Enabled is Enabled

Non-Trusted Read Security is Allow Access

Non-Trusted Write Security is Allow Access

There are other security features you may wish to utilize here, such as Trusted Phone numbers.

Page 7of 9

Port Filtering and Outbound Ports

To prevent outbound http and https traffic over the air from the Raven XE, I have utilized Port

Filtering. Under Security –Port Filtering Outbound, enter ports 80 and 443 to be blocked.

Page 8of 9

Trusted Inbound/Outbound IP Address

Using the ACEManager, you can set certain Static IP addresses as trusted for both Inbound and

outbound traffic for the router. If this router will be put inside a network, this option should be

looked at.

Per the manual, Trusted IPs Inbound restrict access to the router and all LAN connected devices.

You would use the Public IP Address that someone would be accessing the Raven XE over the

air.

Per the manual, Trusted IPs Outbound restrict access to external networks to IPs in the list.

Reboot the Raven XE

At this point in the setup, you should reboot the Raven XE.

Using the Raven and Additional Information

Sending & Receiving SMS Messages

To send SMS messages, login to the Raven XE via SSH. The following are basic commands to send the

message:

at*smsm2m="1XXXXXXXXXX This is SMS test message."

Page 9of 9

To send a test message to itself:

at*phonehome=1XXXXXXXXXX

1XXXXXXXXXX is the number for the Raven XE.

To see if the Raven XE is receiving text messages, send one to it. Then from the ACEManager, go to

Services –SMS –SMS Security. There are 2 fields called Last Incoming Phone Number and Last Incoming

Message you can see if it came in. Press Refresh if you do not see it immediately.

Over The Air Access

To utilize Over the Air access, you must have a data plan. If you do not, you will not be able to access

the ACEManager remotely over the air; additionally, you will not be able to access the internet utilizing

the Raven XE. From a security point of view, this is a good thing. If the Raven XE is only to be used as an

SMS gateway, simply get a SIM card with Text and Minutes only. Inductive Automation tested with a T-

Mobile SIM card with only text and minutes; we were unable to access the ACEManager over the air and

when the Raven XE was acting as the Primary Gateway, we were unable to get http traffic out.

Troubleshooting Notes:

(1) To reset your device back to factory defaults, you must hold down the reset button between 45

and 60 seconds. At that point you will see the lights flash from left-to-right and right-to-left. Do

not be fooled by the flashing lights after 5 seconds of holding down the reset button. It is a

flashing pattern of lights, left-to-right.

(2) If you are putting the Raven XE on your network and you discover certain computers on your

network start behaving incorrectly (intermittent connection drops, packet routing problems to

name a couple), this is because the Raven XE is also a router and it is attempting to act as such.

What is happening is that it is conflicting with the primary router you already have on the

network. To solve this problem, go in your ACEManager under LAN –Host Port Routing Tab and

disable the Primary Gateway.

Andere Sierra Wireless Tor Handbücher

Sierra Wireless

Sierra Wireless LS300 Installationshandbuch

Sierra Wireless

Sierra Wireless FX30S Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink RV50 Series Installationshandbuch

Sierra Wireless

Sierra Wireless oMG 500 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink ES450 Installationshandbuch

Sierra Wireless

Sierra Wireless AirLink GX400 Installationshandbuch

Sierra Wireless

Sierra Wireless AirLink GX400 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink GX400 Bedienungsanleitung

Sierra Wireless

Sierra Wireless FX30S Bedienungsanleitung

Sierra Wireless

Sierra Wireless Raven XE Bedienungsanleitung

Sierra Wireless

Sierra Wireless LS300 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink FXT Series Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink GX440 Bedienungsanleitung

Sierra Wireless

Sierra Wireless oMG 2000 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink Raven XE Bedienungsanleitung

Sierra Wireless

Sierra Wireless Airlink GX450 Installationshandbuch

Sierra Wireless

Sierra Wireless LS300 Bedienungsanleitung

Sierra Wireless

Sierra Wireless LS300 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink GX Series Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink GX440 Bedienungsanleitung

Sierra Wireless

Sierra Wireless airlink es440 Bedienungsanleitung

Sierra Wireless

Sierra Wireless Raven XT Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink PinPoint X Bedienungsanleitung

Sierra Wireless

Sierra Wireless FX30 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung