Sierra Wireless Airlink GX450 Bedienungsanleitung

QUICK START GUIDE

GX450 Modem

TRANSFORMING THE WAY THE WORLD WORKS

This guide provides step-by-step instructions for a quick setup of the GX450 modem.

STEP 1: INSTALLTHE SIM CARD

1. Ensure that the device is powered o.

2. Remove the four screws attaching the black cover to the gateway’s body and then remove the cover.

3. Slide the SIM card into the SIM card holder. Note the location of the notched corner for correct alignment.

4. Re-attach the cover using all 4 screws to maintain the IP64 rating.

STEP 2: CONNECT THE CELLULAR ANTENNA

1. Attach the supplied antenna to the magnetic antenna base. Note the rubber O-ring location to ensure a proper seal.

2. Attach the magnetic antenna base cable to the GX450 cellular connector. The GPS and Diversity connectors will not be used.

STEP 3 CONNECT THE DISPLAY OR RECEIVER

See the wiring diagrams. In all instances, ensure that the equipment is powered o before connecting it to the modem.

AG-372 receiver

1. Ensure the receiver is powered o.

2. Using cable P/N 109863, attach connector P1 to Port B on the AG-372 receiver.

3. Attach connector P2 to the serial port on the GX450 modem.

4. Attach connector P3 to the power port on the GX450 modem.

TM-200 Module

1. Ensure the TM-200 Module is powered o

2. Using cable P/N 109865, attach connector P1 to the ethernet port on the GX450 modem and

then attach connector P2 to the ethernet expansion port on the TM-200 Module or to the

expansion port on the EXP-100 module.

3. Using cable P/N 109862, attach connector P1 to the power port on the GX450 modem.

4. Connect R1 to P2 on cable P/N 92676 on the TM-200 Module.

FmX/FM-1000 integrated display

1. Ensure the display is powered o.

2. Connect USB hub P/N 83517 to the USB port on the back of the display.

3. Using cable P/N 109864, attach the USB port to the USB hub and then attach the micro USB

connector to the GX450 modem.

4. Using cable P/N 110832, connect P2 to Port A, B, C, D, or to a port replicator.

5. Attach connector P1 to connector R1 of cable P/N 109862.

6. Attach connector P1 of cable 109862 to the power port on the GX450. modem.

CFX-750 / FM-750 display

1. Ensure the display is powered o.

2. Connect the USB hub P/N 83517 to the USB port on the back of the display.

3. Using cable P/N 109864, attach the USB port to the USB hub and then attach the micro USB

connector to the GX450 modem.

4. Using cable P/N 110832, connect P2 to Port A, B, or to a port replicator.

5. Attach connector P1 to connector R1 of cable P/N 109862.

6. Attach connector P1 of cable P/N 109862 to the power port on the GX450 modem.

WIRING DIAGRAM: AG-372 RECEIVER

❶

❷

❸

❹

❺

❻

❼

Item Description P/N Item Description P/N

1AG-372 antenna 5Mounting plate 62034

2Power cable assembly, GX-450 modem 109863 6Cellular antenna (international) 110024

3GX450 modem 7Whip antenna (USA and Canada

only)

51227

4Magnetic antenna base cable 109989

WIRING DIAGRAM: TM-200 MODULE (FOR USE WITH THE TMX-2050 / XCN-2050 DISPLAY)

❶

Item Description P/N Item Description P/N

1TM-200 Module 6Mounting plate 62034

2TM-200 14-pin power, CAN, and I/O cable 92676 7Cellular antenna (international) 110024

3Power cable assembly, GX450 modem 109862 8Whip antenna (USA and Canada only) 51227

4GX450 modem 9Ethernet cable, GX450 modem to TM-200

Module

109865

5Magnetic antenna base cable 109989

❶

❷❸

❹

❺

❻

❼

❽

❾

WIRING DIAGRAM: TM-200 MODULE WITH EXP-100 PORT REPLICATOR

Item Description P/N Item Description P/N

1 Cable assembly, EXP-100 port replicator

to patch 1 meter

102730 8GX450 modem

2Power cable assembly, GX450 modem 109862 9Magnetic antenna base cable 109989

3EXP-100 port replicator 10 Mounting plate 62034

4Cable assembly, EXP-100 adaptor to

Ethernet

100906 11 Cellular antenna (international) 110024

5TM-200 14-pin power, CAN, and I/O cable 92676 12 Whip antenna (USA and Canada only) 51227

6TM-200 Module 13 Cable assembly, EXP-100 adapter

TM-100 Module to Ethernet

(see also Note, above)

100904

7Ethernet cable, GX450 modem to TM-

200 Module

109865

❶

❷

❸

❹

❺

❻

❼

❽

❾

❿

⓫

⓬

⓭

❶

Note: If the EXP-100 port

replicator is required and

is not already installed,

order P/N 101990-01.

If the EXP-100 port

replicator is already

installed, but without the

Ethernet adaptor,

P/N 101990-00, order

cables P/N 102730 and

P/N 100906 to attach a

GX450 modem.

WIRING DIAGRAM: FMX / FM-1000 INTEGRATED DISPLAY

❶

Item Description P/N Item Description P/N

1USB hub 83517 6Magnetic antenna base cable 109989

2FmX® / FM-100™ integrated display 7Mounting plate 62034

3Power assembly, FmX/FM-1000 integrated

display

110832 8Cellular antenna (international) 110024

4Power cable assembly, GX450 modem 109862 9Whip antenna (USA and Canada only) 51227

5GX450 modem 10 USB cable assembly, GX450 modem to

FmX /FM-1000 integrated display

109864

❶

❷

❸

❹

❺

❻

❼

❽

❾

❿

WIRING DIAGRAM: CFX-750 / FM-750 DISPLAY

❶

Item Description P/N Item Description P/N

1USB hub 83517 6Magnetic antenna base cable 109989

2CFX-750™ /FM-750™ display 7Mounting plate 62034

3Power assembly, CFX-750 display 110832 8Cellular antenna (international) 110024

4Power cable assembly, GX450 modem 109862 9Whip antenna (USA and Canada

only)

51227

5GX450 modem 10 USB cable assembly, GX450 modem

to CFX-750 /FM-750 display

109864

❶

❷

❸

❹

❺

❻

❼

❽

❾

❿

STEP 4: CONNECT TO THE NETWORK

The rst time the gateway is powered on its home network, it automatically starts the activation/provisioning process and attempts to

connect to the network. This process typically takes 5-10 minutes. A successful connection is indicated by a solid green network LED.

STEP 5: CONFIGURE THE NETWORK

For most cellular plans, the modem will automatically congure itself properly. If issues

persist in establishing a cellular connection (blinking red network LED) the APN may need

to be entered manually. To do this:

1. On a computer powered by a Windows® operating system (connected to the

modem using an Ethernet cable) or using the modem service tool on the

TMX-2050/XCN-2050 display that is connected to the GX450 modem, enter

http://192.168.88.3:9191 in the web browser. The ACEmanager login screen

appears.

Note: It may take the gateway 2-3 minutes to respond after the initial power up.

2. The administrator username is entered by default. Enter the default password

Wilco2016 and then click Login. The Status / Home screen appears.

3. Check the Network State eld. It should read Network Ready, which indicates that the

gateway is connected to the network. If not, refer to

STEP 4 above.

4. On the WAN/Cellular page, there is a section for User Entered APN - enter the custom

APN here if the modem does not automatically detect the cellular provider’s APN

number.

STEP 6: CONFIGURE THE CORRECTION SOURCE

Refer to the User Guide for the display or receiver for information on the setup procedure for

VRS setup.

LED Color / Pattern Description

Power O No power or input voltage ≥ 36 VDC or ≤ 9 VDC.

Solid green Gateway is connected to nominal power and is operating normally.

Flashing amber / green Gateway has a GPS x.

Solid amber Gateway is entering a low power mode or system low level boot.

Solid red Gateway is not operational (failure or in low power mode).

Network Solid green Network Ready (LTE service available for GX450 modem).

Flashing amber / green Network Ready (no LTE service available for GX450 modem).

Flashing green (3 s on, 1 s o) Network Ready (WAN over WiFi—gateway in WiFi client mode).

Flashing green (1 s on, 0.5 s o) Network Ready - Roaming (LTE service available for GX450 modem).

Flashing amber/green/o Network Ready - Roaming (no LTE service for GX450 modem).

Flashing amber No service.

Solid amber Connecting to the network.

Flashing red Authentication/negotiation failed (EV-DO only).

Solid red Link Down. No cellular network is present, no network coverage at current

location, or the gateway is in radio passthru mode.

Signal Solid green Good signal (RSSI ≥ -85 dBm).

Solid amber Marginal signal (-100 dBm, < RSSI <-85 dBm).

Solid red Poor signal (-110 dBm ≤ RSSI ≤ -100 dBm).

Flashing red No signal, RSSI (< -100 dBm).

Activity (ALEOS

4.4.0 or later)

O Normal operation.

Flashing green Trac is being transmitted or received over the WAN interface.

Flashing red Trac is being transmitted or received over the serial port. This behavior

only appears if the AirLink GX Series gateway is congured to display it.

Refer to the ALEOS Software Conguration Guide for details.

Flashing amber Trac is being transmitted or received over both the WAN interface and

the serial port. This behavior only appears if the AirLink GX Series gateway

is congured to display it. Refer to the ALEOS Software Conguration

Guide for details.

LED BEHAVIOUR

Trimble Inc.

10368 Westmoor Drive

Westminster CO 80021

USA

in other countries. FieldLevel, FM-750, FM-1000, TMX-2050, and XCN-2050 are trademarks of Trimble Inc. Microsoft and Windows are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other trademarks are the property of their respective

owners. Version 1.00, Rev A (November 2016). P/N 110896-00-ENG

TRANSFORMING THE WAY THE WORLD WORKS

*110896-00-ENG*

Product Update to the following software version

FmX / FM-1000 integrated display Version 10.01 or later, released December 2016

CFX-750 / FM-750 display Version 7.71 or later, released October 2016

TMX-2050™ / XCN-2050™ display Version 4.31 or later, released December 2016

AG-372 antenna Version 6.20 or later, released April 2016

FIRMWARE VERSION MATRIX

Andere Handbücher für Airlink GX450

Inhaltsverzeichnis

Andere Sierra Wireless Modem Handbücher

Sierra Wireless

Sierra Wireless DART 200 CDPD Modem Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirCard 597E Bedienungsanleitung

Sierra Wireless

Sierra Wireless AT&T USBConnect Shockwave Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink Raven XT Bedienungsanleitung

Sierra Wireless

Sierra Wireless V4221-AA - Raven X EV-DO Revision A Bedienungsanleitung

Sierra Wireless

Sierra Wireless U598 Bedienungsanleitung

Sierra Wireless

Sierra Wireless Raven X HSDPA Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirCard 595 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink MP595 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirPrime WP7601 Kurzanleitung zur Einrichtung

Sierra Wireless

Sierra Wireless PinPoint X Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirCard 319U Bedienungsanleitung

Sierra Wireless

Sierra Wireless USBConnect Lightning Bedienungsanleitung

Sierra Wireless

Sierra Wireless USB Modem Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink MP890 Bedienungsanleitung

Sierra Wireless

Sierra Wireless Compass 597 Bedienungsanleitung

Sierra Wireless

Sierra Wireless O2 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink GL8200 Bedienungsanleitung

Sierra Wireless

Sierra Wireless Sprint 598U Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirLink MP Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRPRIME WISMO218 Bedienungsanleitung

Sierra Wireless

Sierra Wireless iPASS Bedienungsanleitung

Sierra Wireless

Sierra Wireless AirCard 250U Bedienungsanleitung

Sierra Wireless

Sierra Wireless compass series Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung