SightLine 3000-OEM Benutzerhandbuch

 
© SightLine Applications, Inc. 
EAN-Startup Guide 3000-OEM
2023-05-04 
Exports: Export Summary Sheet 
EULA: End User License Agreement 
Web: sightlineapplications.com 
Sales: sale[email protected] 
Support: [email protected] 
Phone: +1 (541) 716-5137 
 
 
1Overview ................................................................1 
1.1 Additional Support Documentation.......................1 
1.2 SightLine Software Requirements..........................1 
2Safe Device Handling..............................................1 
33000-EVAL Kit with 3000-mIO................................1 
4Hardware Bench Setup ..........................................2 
4.1 Additional SightLine Adapter Boards .....................4 
5Network Configuration ..........................................4 
6Serial Communications ..........................................5 
6.1 Direct Serial Connection (optional)........................5 
7Panel Plus...............................................................6 
7.1 Camera Acquisition................................................7 
7.2 Stream Network Video to This PC..........................8 
8Summary................................................................9 
8.1 Demo Mode .........................................................10 
9Modifying Encoder Parameters ...........................10 
10 Troubleshooting...................................................11 
10.1 Network Connection............................................11 
10.2 3000-OEM HD-SDI Camera Input.........................12 
10.3 Send Diagnostic Files to SightLine Support..........13 
10.4 Questions and Additional Support.......................13 
 
CAUTION: Alerts to a potential hazard that may result in personal injury, or an unsafe practice that causes damage to the equipment 
if not avoided. 
IMPORTANT: Identifies crucial information that is important to setup and configuration procedures. 
Used to emphasize points or reminds the user of something. Supplementary information that aids in the use or understanding of the 
equipment or subject that is not critical to system use. 
 
 
 
 
 
 
 
 

EAN-Startup Guide-3000-OEM

1Overview

The 3000-OEM Startup Guide provides the steps for connecting, configuring, and evaluating the 3000-

OEM video processing board on the SLA-3000-mIO interface board. The mIO is optimized for

connections in an integrated assembly. Compared to the SLA-3000-IO the mIO is smaller,

uncomplicated, has small round wire interfaces and supports a two-board stack height.

Boards with SLE options enabled use the same startup procedure.

1.1 Additional Support Documentation

Additional Engineering Application Notes (EANs) can be found on the Documentation page of the

SightLine Applications website.

The Panel Plus User Guide provides a complete overview of settings and dialog windows. It can be

accessed from the Help menu of the Panel Plus application.

The Interface Command and Control (IDD) describes the native communications protocol used by the

SightLine Applications product line. The IDD is also available as a PDF download on the Documentation

page under Software Support Documentation.

1.2 SightLine Software Requirements

IMPORTANT: Starting with 3.6.x software and above, only the 4000 and 1700 platforms will be

supported. The 1500 and 3000 platforms will continue to be supported in 3.5.x software. Some

3.6.x features may not be available on 1500 and 3000 platforms.

IMPORTANT: The Panel Plus software version should match the firmware version running on the

board. Firmware and Panel Plus software versions are available on the Software Download page.

2Safe Device Handling

CAUTION: To prevent damage to hardware boards, disconnect all input power to OEMs and adapter boards before

connecting or disconnecting cables including all FFC, FPC, KEL, HDMI, and round wire (Molex) cables.

CAUTION: To prevent damage to hardware boards, use a conductive wrist strap attached to a good earth ground.

Before picking up an ESD sensitive electronic component, discharge built up static by touching a grounded bare

metal surface or approved antistatic mat.

33000-EVAL Kit with 3000-mIO

Provides a complete laboratory bench/development interface with standard connectors. For additional

options and interface boards, please contact Sales. To review all the interface board options, see the

products pages on the SightLine Applications website.

Table 1: 3000-EVAL Kit with 3000-mIO

Part Number

Qty

Description

Part Number

Qty

Description

3000-OEM

Video processing board

SL00764

HDMI Type A male connector standard

SLA-3000-mIO*

Main interface board for the 3000-

OEM

SLA-CAB-0303

3-pin PicoBlade to DB9

4000-OEM-MP

4000-OEM mounting base

SLA-CAB-0403

6-inch cable, 4-Pin PicoBlade to modular

jack

EAN-Startup Guide-3000-OEM

(3000-EVAL Kit with 3000-mIO continued)

SLA-DIST

PWR/ENET distribution board

SLA-CAB-P103

RF179 cable assy, BNC bulkhead jack to

MCX

3000-HDSDI-IN

HD-SDI interface board

SLA-CAB-0302

3-pin PicoBlade pigtail

SLA-CAB-0404

4-pin Molex PicoBlade, 3.0 inches,

GEN (WHT)

SLA-CAB-0402

4-pin PicoBlade pigtail

SLA-CAB-0405

4-pin Molex PicoBlade, 3.0 inches,

PWR (BLK/RED)

SLA-CAB-HD10

10cm Length FPC ribbon flat cable for

HDMI

SLA-PAD-010

Thermal pad 1.0-inch x 1.0-inch x

0.010 inch

SLA-CAB-MCX2BNC

Cable, MCX (RA) to BNC(M) for HDSDI-

SLA-PAD-020

Thermal pad 0.75-inch X 0.75-inch x

0.020 inch

SLA-CAB-ETH0

Ethernet cable CAT 5e 3ft

SLA-PAD-125

Thermal pad 0.250-inch x 0.250-inch

x 0.125 inch

SLA-CAM-HDSDI

HD-SDI 1080p camera

SLA-PWR-B12V

12V power supply w/2-pin connector

SLA-PWR-A12V

12V Power supply for camera

SLA-CAB-1504

12V power cable to PicoBlade

SLA-MSD-ADPT

SD adapter

SLA-MSD-32GB

32 GB microSD memory card (class 10

SDHC)

SLA-DOC-LICENSE

Hardware license

SLA-CAB-S001

Serial adapter (stripped)

Mounting hardware

Spacers and mounting screws

*The SLA-3000-IO board is alternate interface board for the 3000-OEM that comes in the standard 3000-EVAL kit.

4Hardware Bench Setup

IMPORTANT: To prevent damage to hardware boards, disconnect the power before connecting or

disconnecting all cable connections.

The 3000-HDSDI-IN is connected to J4 on the 3000-OEM or VIN1 on the SLA-3000-IO. The SLA-DIST

provides power switch and standard bench interface connections for power and ethernet.

Cable connections:

•SLA-CAB-MCX2BNC: Connects to J1 (MCX jack) on the 3000-HDSDI-IN board and to the green BNC

connector of the 1080p camera. The yellow BNC connector is for analog use only.

•SLA-CAB-SMA2BNC: Analog monitor cable (optional). Connects to J8 on the SLA-3000-mIO (VOUT

on the SLA-3000-IO).

•SLA-CAB-ETH0: Connects to the Ethernet port and to the network switch or host PC.

•SLA-CAB-0404: Connects to J3 on the SLA-DIST and J4 on the SLA-3000-mIO. Provides Ethernet to

the 3000-OEM.

•SLA-CAB-0405: Connects to J2 on the SLA-DIST and J9 on the SLA-3000-mIO. Provides power to the

3000-OEM.

•SLA-PWR-A12V (110-250VAC input / 12VDC output): Connects to the red power connector on the

1090p camera.

•SLA-PWR-B12V (110-250VAC input / 12VDC output): Connects to J4 on the SLA-DIST (SLA-3000-

mIO).

•SLA-PWR-C12V (110-250VAC input / 12VDC output): Connects to J5 on the SLA-3000-IO.

EAN-Startup Guide-3000-OEM

Power and network connectivity LEDs:

•A green light on the 3000-IO or 3000-mIO board indicates that all boards are powered on. An

amber light on the 3000-OEM board verifies network connection.

•To prevent voltage spikes to the board, plug in the power adapter to an AC power source first and

then connect to the board.

Figure 1: Typical Bench Hardware Setup - SLA-3000-mIO

Figure 2: Alternate Bench Hardware Setup - SLA-3000-IO

Serial (0)

Network Switch or

PC Direct

SLA-DIST

SLA-PWR-B12V

Optional

Analog

Monitor

SLA-CAB-0405 (J9)

SLA-CAB-0404 (J4)

SLA-CAB-MCX2BNC (VIN1) to camera

3000-OEM +

SLA-3000-mIO on J1 +

SLA-3000-HDSDI-IN on J4

1080p Camera

SLA-PWR-A12V

SLA-CAB-ETHO

HDSDI Input

(Green BNC

Connector)

SLA-CAB-SMA2BNC (not included)

Ethernet Port

IMPORTANT: Disconnect all input power to

OEMs and adapter boards before connecting

or disconnecting cables.

Ethernet Port

Network Switch or PC Direct

VOUT

SLA-PWR-C12V

Serial (alternate)

Optional

Analog

Monitor

SLA-CAB-SMA2BNC (included)

SLA-CAB-ETH0

SLA-CAB-MCX2BNC

(VIN1) to camera

3000-OEM with heatsink +

SLA-3000-IO +

SLA-3000-HDSDI-IN on VIN1

1080p Camera

SLA-PWR-A12V

HDMI Out

MicroSD Card

HDSDI Input

(Green BNC

Connector)

IMPORTANT: Disconnect all input

power to OEMs and adapter

boards before connecting or

disconnecting cables.

EAN-Startup Guide-3000-OEM

4.1 Additional SightLine Adapter Boards

SightLine adapter boards provide different I/O, camera inputs, or digital outputs. The boards can be

attached directly to the 3000-OEM or through a secondary adapter allowing customers to swap out

modules for custom configurations. This setup guide assumes the initial use of the EVAL kit and the

HDSDI input. Customer specific configurations with other camera input boards is fully supported.

On the SLA-3000-IO board, VIN0/(J3) has camera channels 0 and 1 assigned. VIN1/(J4) has camera

channel 2 assigned. Both the SLA-3000-mIO and SLA-3000-IO supports SightLine interface boards on

either of these connectors.

IMPORTANT: 3000-AB board only - If the SLA-3000-AB board is installed on VIN0/J3, both analog

inputs can be used. If it is installed on VIN1/J4, only the J3 (input 0) can be used.

3000-OEM

SLA-3000-IO

Serial Port

Camera Index Panel Plus

0/1

VOUT

VIN0

CAM0/CAM1

VIN1

CAM2

Figure 3: 3000-OEM Serial Port and Connector Reference

5Network Configuration

The 3000-OEM board can be connected directly to the host PC or through a network switch. During

startup, the board sends three DHCP discover requests in three second intervals. It will self-assign the

link-local address of 169.254.1.181 if it does not receive a response.

Refer to EAN-Network-Configuration for more network configuration information.

SightLine recommends assigning a static IP on the PC when a DHCP server is not present on the

network.

If additional assistance is needed to assign a static IP address to the host PC, contact a network

administrator or search online for procedures that corresponds with the current PC operating

system.

Figure 4: Network Configuration Options

J1 - Serial Port 0/1 J2 - Serial Port 4

J4/VIN1 - Serial Port 3

J3/VIN0 - Serial Port 2

Host PC

User assigned static

IP: 169.254.1.10

3000-OEM + SLA-3000-mIO + SLA-3000-HDSDI-IN

Ethernet Cable

Default IP assigned to the 3000-

OEM: 169.254.1.181

Network Switch

or PC Direct

EAN-Startup Guide-3000-OEM

Configuration notes:

•If a wireless adapter is active on the host PC it should be disabled.

•If using the link local address, assign a static IP address to the host PC of 169.254.x.x, where (x) is 1-

254 (do not use 181). Use a subnet mask of 255.255.0.0.

•Problems with outbound streaming are often related to setting/assigning IP addresses and ports.

See the Encoding Configuration settings in EAN-Encoding for advanced settings.

6Serial Communications

For a direct serial connection use the 9-pin serial connection. A serial COM connector is included in the

EVAL kits for both the SLA-3000-mIO and the SLA-3000-IO boards. Connecting to the serial COM port

on both boards from a host PC requires a null modem adapter or null modem serial cable.

For the SLA-3000-IO the serial COM connector must be wired to the board power adapter as shown in

Figure 5. The pinout for this cable can be found in the ICD-Adapter-Boards document.

Use a direct serial connection for troubleshooting or if a network connection cannot be established.

Figure 5: Serial COM and Power Connection-SLA-3000-IO

6.1 Direct Serial Connection (optional)

1. Connect the serial cable to the 3000-OEM board and host PC as described in Serial

Communications.

2. From the Connect tab, click the Refresh List button to get a list of available COM ports.

3. Use the drop-down menu and click on a COM port to select it.

4. Click the Disconnected (click to connect) button.

IMPORTANT: Video cannot be streamed over a serial connection.

Figure 6: Direct Serial Connection

J5 (5-pin)

SLA-PWR-C12V

Null Modem Serial

Cable to PC

Serial 0

SLA-3000-IO

Board

EAN-Startup Guide-3000-OEM

7Panel Plus

This section covers the Panel Plus setup and configuration process. Panel Plus provides a basic

graphical interface to the features and functions of the 3000-OEM and 3000-mIO board.

Before connecting with the Panel Plus software, the 3000-OEM and 3000-mIO boards should be

powered up and connected through:

-a network switch or directly to the host PC (preferred) or,

-Direct serial connection (for troubleshooting or if a network connection cannot be established).

1. Go to the Software Downloads page on the SightLine website and download the Panel Plus

application installer. Older releases are available under the Previous Versions section.

IMPORTANT: The firmware version number and Panel Plus Software version number should match.

If the board firmware version is initially unknown, reference the SightLine invoice that came with

the board when it was purchased.

2. Launch the installer file and follow the prompts. After installation open the Panel Plus application.

3. The first time that Panel Plus is launched, a Windows Security Alert prompt should appear. Select

Allow Access to create a firewall exception (Figure 7).

Approving private network access is sufficient in most cases. Check public networks if directly

connecting to the board.

Figure 7: Windows Security Alert Prompt

IMPORTANT:

•Do not cancel this prompt. Failure to allow access at this point will not allow the Panel Plus

application to connect to the board. See the Troubleshooting section for more information.

•Before using the Panel Plus program, review the Panel Plus User Guide in the Help section of the

Panel Plus application for additional user and setup information.

C:\Program Files (x86)\sightline applications\sla-panel-plus

3.05.03\slapanelplus.exe

EAN-Startup Guide-3000-OEM

4. Network connection to the board:

a. From the Connect tab, click the Refresh List button

to get a list of boards on the network.

b. Use the drop-down menu and click on the

appropriate board to select it.

c. Click the Disconnected (click to connect) button.

Figure 8: Network Connection to the OEM Board

Once the connection is successful, the button changes to Connected.

5. Verify the connection. When Panel Plus has successfully connected to the 3000-OEM board,

operating information is displayed under the Video Output section and the bottom status bar in

Panel Plus. If the connection was not successful, this information will not be present or incomplete.

IMPORTANT: For optimal performance, monitor the board temperature. Board temperatures

should be below 185°F (85°C). To keep boards within the optimal temperature range, use the

included heatsink during bench testing. For more information about thermal management, see the

ICD-3000-OEM.

Figure 9: Firmware Version and Enabled Features

7.1 Camera Acquisition

1. From the main menu go to Configure »Aquisition Settings. This dialog window allows changes to

the camera configuration.

App bit code

with listed

features

Firmware Ver: 3.5.3.30 HW Rev:C, temp: 125°F [37°C]

SVN Revision: 69395, Build Date: 08/09/2022, Build Time: 02:41:01

Operating

information

EAN-Startup Guide-3000-OEM

2. Since the SLA-3000-HDSDI-IN board is on J4 on the 3000-OEM or VIN 1 on the 3000-IO, set the

Camera Index to Cam 2. Set the Camera Type to Generic Digital.

3. In the Auto Fill drop-down menu, select HD-SDI 720p from the Auto Fill menu or enter the Height and Width

settings of the connected camera.

If using a camera that is not configured for 720P, choose the corresponding option under Auto Fill

that matches the camera., e.g., HD-SDI 1080p.

If the camera is listed, the Auto Fill drop-down menu automatically populates the relevant fields

with the correct settings as shown in Figure 10.

Figure 10: Camera Acquisition Auto Fill Settings Example - HD-SDI 720p

4. After changes have been made, the Apply button will turn red indicating that a change has been

detected. Click Apply to apply the changes. Close the Acquisition Settings dialog window.

5. Save and activate the settings:

a. Main menu » Parameters » Save to Board.

b. Main menu » Reset » Board.

c. After the system reboots reconnect to the board. Make sure the board connects.

See the camera configuration tables for all third-party cameras and lens assemblies that are

currently supported by SightLine software. Includes configuration and setting support guidance.

7.2 Stream Network Video to This PC

To stream network video to the

connected PC, click the Connection

tab in Panel Plus and then click

Stream Network Video to this PC.

Figure 11: Stream Network Video to PC

EAN-Startup Guide-3000-OEM

8Summary

This completes the startup guide for the 3000-OEM board. See the Panel Plus User Guide (main menu »

Help » User Guide) for additional user and setup information.

If the board has been connected to a camera and encoding functions are part of the configuration,

video will be displayed in the main window. On the Connect tab of Panel Plus, the purchased functions

are checked and enabled. To add additional features to 3000-OEM board, contact Sales.

To modify the encoder parameters of the OEM, see the Modifying Encoder Parameters section.

Figure 12: Panel Plus Connection to Board

IMPORTANT: Not all 3000-OEM purchased configurations include encoded IP video, e.g., the

Tracker-only configuration. For configurations that include encoding, video will be displayed in the

Panel Plus main window. Tracker-only configurations will display processed video on the analog

output only. An analog monitor is required for viewing this output.

Panel Plus

User Guide

Enabled

Features

Demo Mode

Andere Handbücher für 3000-OEM

Inhaltsverzeichnis

Andere SightLine Computerhardware Handbücher

SightLine

SightLine 1750-OEM Bedienungsanleitung

SightLine

SightLine EAN-4000-OEM Bedienungsanleitung

SightLine

SightLine 1750-OEM Bedienungsanleitung

SightLine

SightLine ICD-1750-OEM Bedienungsanleitung

SightLine

SightLine 1750-OEM Benutzerhandbuch

SightLine

SightLine ICD-4000-OEM Bedienungsanleitung

SightLine

SightLine 1750-OEM Bedienungsanleitung

SightLine

SightLine 3000-OEM Benutzerhandbuch

SightLine

SightLine 1500-OEM Bedienungsanleitung

SightLine

SightLine ICD-1750-OEM Bedienungsanleitung

SightLine

SightLine 1500-EVAL Kit Benutzerhandbuch

SightLine

SightLine 3000-OEM Bedienungsanleitung

SightLine

SightLine 1750-OEM Bedienungsanleitung

SightLine

SightLine ICD-4000-OEM Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung