SIGLENT TECHNOLOGIES SDS2000X-E Series Bedienungsanleitung

User Manual

SDS2000X-E Series Digital

Oscilloscope

UM0102E-E01A

SIGLENT TECHNOLOGIES CO., LTD.

SIGLENT

2 SDS2000X-E User Manual

Trademark Information

SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.

Declaration

SIGLENT products are protected by patent law in and outside of the P.R.C.

SIGLENT reserves the right to modify or change parts of or all the specifications or pricing policies at

company’s sole decision.

Information in this publication replaces all previously corresponding material.

Any way of copying, extracting or translating the contents of this manual is not allowed without the

permission of SIGLENT.

Product Certification

SIGLENT guarantees this product conforms to the national and industrial standards in China and

other international standards. Conformance certification is in progress.

If you have any problem or requirement when using our products, please contact SIGLENT

TECHNOLOGIES CO., LTD

Add：3//F, Bldg No.4, Antongda Industrial Zone, 3rd Liuxian Road, Bao’an District, Shenzhen, 518101,

P.R.China

Tel：400-878-0807

E-mail：sales@siglent.com

http://www.siglent.com

SIGLENT

3 SDS2000X-E User Manual

Safety Information

General Safety Summary

Carefully read the following safety precautions to avoid any personal injury or damage to the

instrument and any products connected to it. To avoid potential hazards, please use the

instrument as specified.

Use Proper Power Line

Only the power cord designed for the instrument and authorized by the local country should be used.

Ground the Instrument

The instrument is grounded through the protective earth conductor of the power line. To avoid electric

shock, please make sure the instrument is grounded correctly before connecting its input or output

terminals.

Connect the Signal Wire Correctly

The potential of the signal wire is equal to the earth, so do not connect the signal wire to a high

voltage.

Look Over All Terminals’ Ratings

To avoid fire or electric shock, please look over all ratings and read the instructions for the instrument.

Before connecting the instrument, please read the manual carefully to gain more information about

important ratings.

Use Proper Overvoltage Protection

Make sure that no overvoltage (such as that caused by a thunderstorm) can reach the product, or

else the operator might expose to danger of electrical shock.

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid damages induced by static

discharge. Always ground both the internal and external conductors of the cable to release static

before connecting.

Keep Well Ventilation

Inadequate ventilation may cause an increasing in operting temperature, which will eventually

damage the instrument. So keep well ventilation and inspect the intake and fan regularly.

Avoid Circuit or Components Exposed

Do not touch exposed contacts or components when the power is on.

Use proper Fuse

Use only the specified fuse.

Do Not Operate Without Covers

Do not operate the instrument with covers or panels removed.

Do Not Operate With Suspected Failures.

If you suspect damage occurs to the instrument, have it inspected by qualified service personnel

SIGLENT

4 SDS2000X-E User Manual

before further operations. Any maintenance, adjustment or replacement especially to circuits or

accessories must be performed by SIGLENT authorized personnel.

Do Not Operate in Wet Conditions.

In order to avoid short circuiting to the interior of the device or electric shock, please do not operate in

a humid environment.

Do Not Operate in an Explosive Atmosphere.

In order to avoid damages to the device or personal injuries, it is important to operate the device away

from an explosive atmosphere.

Keep Product Surfaces Clean and Dry.

To avoid the influence of dust and/or moisture in air, please keep the surface of the device clean and

dry.

Handling Safety

Please handle with care during transportation to avoid damaging buttons, knob interfaces and other

parts on the panels.

Only probe assemblies which meet the manufacturer’s specifications shall be used.

When using SIGLENT probe assemblies, the probe assemblies shall be insulated from the measured

circuits by double or reinforced insulation.

All probe assemblies should meet the requirements of UL 61010-031 and CAN/CSA-C22.2 No.

61010-031-07.

Do not position the equipment so that it is difficult to disconnect an attached device (detachable plug).

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

SIGLENT

5 SDS2000X-E User Manual

Safety Terms and Symbols

Terms in this Manual. These terms may appear in this manual:

WARNING

Warning statements indicate the conditions or practices that could

result in injury or loss of life.

CAUTION

Caution statements indicate the conditions or practices that could

result in damage to this product or other property.

Terms on the product. These terms may appear on the product:

DANGER Indicates direct injuries or hazards that may happen.

WARNING Indicates potential injuries or hazards that may happen.

CAUTION Indicates potential damage to the instrument or other property that may happen.

Symbols on the product. These symbols may appear on the product:

Hazardous protective Earth Warning Test Power Switch

Voltage Terminal Ground

If find such symbols on the product, consult the manual to find out the nature of the potential hazard

and the actions which have to be taken.

SIGLENT

6 SDS2000X-E User Manual

Measurement Category

Measurement Categories

This oscilloscope can make measurements in other circuits that are not directly connected to mains.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Not to use the product for measurements within other measurement

categories, such as CAT II, CAT III, CAT IV.

Do not use the equipment for measurements on mains circuits.

Measurement Category Definitions

Measurement category II is for measurements performed on circuits directly connected to the low

voltage installation. Examples are measurements on household appliances, portable tools and similar

equipment.

Measurement category III is for measurements performed in the building installation. Examples are

measurements on distribution boards, circuit-breakers, wiring, including cables, bus-bars, junction

boxes, switches, socket-outlets in the fixed installation, and equipment for industrial use and some

other equipment, for example. Stationary motors with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the low-voltage installation.

Examples are electricity meters and measurements on primary over current protection devices and

ripple control units.

SIGLENT

7 SDS2000X-E User Manual

Working Environment

Temperature

Operating: 10℃ to +40℃

Non-operation:-20℃ to +70℃

Humidity

Under +35℃:≤90% relative humidity

+35℃ to +40℃: ≤60% relative humidity

WARNING

To avoid short circuiting inside the instrument or electric shock, please do

not operate in humid environment.

Altitude

Operating: less than 3 km

Non-operation: less than 15 km

Degree of protection

IP20

Installation (overvoltage) Category

This product is powered by mains conforming to installation (overvoltage) category II.

WARNING

Make sure that no overvoltage (such as that caused by thunder/lightning) can

reach the product, or else the operator might expose to danger of electric

shock.

Installation (overvoltage) Category Definitions

Installation (overvoltage) category I refers to signal level which is applicable to equipment

measurement terminals connected to the source circuit. In these terminals, precautions are done to

limit the transient voltage to the corresponding low level.

Installation (overvoltage) category II refers to the local power distribution level which is applicable to

equipment connected to the AC line (AC power).

SIGLENT

8 SDS2000X-E User Manual

Ventilation Requirement

This oscilloscope uses a fan to force cooling. Please make sure that the air intake and exhaust areas

are free from obstructions and have free air. When using the oscilloscope in a bench-top or rack

setting, provide at least 10 cm clearance beside, above and behind the instrument for adequate

ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would

damage the instrument. So please keep the instrument well ventilated

during operation and inspect the intake and fan regularly.

SIGLENT

9 SDS2000X-E User Manual

General Care and Cleaning

Care

Do not store or leave the instrument in direct sunshine for long periods of time.

WARNING

To avoid damage to the instrument or probe, please do not leave

them in areas that contain fog, liquid, or solvent.

Cleaning

Please perform the following steps to clean the instrument and probe:.

1. Disconnect the instrument from all power sources, and then clean it with a soft wet cloth.

2. Clean the loose dust on the outside of the instrument and probe with a soft cloth. When cleaning

the LCD, take care to avoid scratching it.

WARNING

To avoid damage to the surface of the instrument and probe, please

do not use any corrosive liquid or chemical cleanser.

WARNING

Make sure that the instrument is completely dry before restarting it to

avoid short circuits or personal injuries.

SIGLENT

10 SDS2000X-E User Manual

L'information de sûreté

Résumé général de sûreté

Lisez soigneusement les mesures de sécurité suivantes pour éviter n'importe quelles blessures ou

les dommages à l'instrument et à tous les produits se sont reliés à eux. Pour éviter des risques,

utilisez svp l'instrument comme indiqué.

Employez la ligne à haute tension appropriée

Seulement le cordon de secteur conçu pour l'instrument et autorisé par le pays local a pu être

employé.

A rectifié l'instrument.

L'instrument est fondu par le conducteur protecteur de terra de la ligne à haute tension. Pour éviter la

décharge électrique, le conducteur moulu doit être relié à la terre. Assurez-vous que l'instrument est

fondu correctement avant de relier ses bornes d'entrée ou de rendement.

Reliez le fil de signal correctement.

Le potentiel de l'au sol de fil de signal est égal à la terre, ainsi ne relie pas le fil de signal à une

tension.

Regardez estimations au-dessus de toutes les bornes des'

Pour éviter le feu ou la décharge électrique, regardez svp au-dessus de toutes les estimations et

instruction de signe de l'instrument. Avant de relier l'instrument, lisez svp le manuel soigneusement

pour obtenir plus d'informations sur les estimations.

Employez la protection appropriée de surtension

Assurez-vous qu'aucune surtension (comme cela provoqué par un orage) ne peut atteindre le produit,

ou bien l'opérateur pourrait exposer au danger du choc électrique.

Empêchement électrostatique

Fonctionnez dans un environnement protecteur de secteur de décharge électrostatique pour éviter

des dommages induits par décharge statique. A toujours rectifié les conducteurs internes et externes

du câble pour libérer la charge statique avant de se relier.

La ventilation insatisfaisante de ventilation

bonne de subsistance peut causer l'augmentation de la température, qui endommagera par la suite

l'instrument. Gardez ainsi la ventilation bonne et inspectez la prise et éventez régulièrement.

Évitez le circuit ou les composants exposés

ne touchent pas les contacts ou les composants exposés quand le courant passe.

Employez l'utilisation appropriée

de fusible seulement le fusible indiqué.

Ne fonctionnez pas sans couvertures

n'actionnent pas l'instrument des couvertures ou des panneaux étant coupés.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIGLENT TECHNOLOGIES Prüfgeräte Handbücher

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS5000X Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS3000X HD Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1104X-E Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SHS800 Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6000A Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS2000 Series Bedienerhandbuch

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6204A Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SHS800 Series QS03008-E01 Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000X-E Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS5000X Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000CFL Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000X Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000 Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS2000X HD Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6000A Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS800X HD Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SAP2500D Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000DL Series Bedienungsanleitung

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1202X-E Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung