Sigma Controls 700 PDL Series Bedienungsanleitung
1
VISIT OUR WEBSITE SIGMACONTROLS.COM
700 SERIES ‘PDL’
PROCESS DATA LOGGER
INSTRUCTION MANUAL
700 SERIES PDL PROCESS DATA LOGGER 062314
2
TABLE OF CONTENTS
INTRODUCTION………………………………………… 3
Ordering Information
S ecifications
Features
WIRING…………………………………………………… 6
Dwg # 700 PDL Process Data Logger
Showing: In uts (8) 4-20 MA
Digital Out ut (4) Form ‘C’ Relays
PROGRAMMING AND INITIAL SETUP……………... 7
In ut Range Selection
Terminal Block Detail
Initial Setu & Programming
Overview/Key Descri tion
PROGRAMMING RECORD SHEET…………………...
11
TROUBLESHOOTING & MAINTENANCE …………..
1
WARRANTY……………………………………………… 13
*U.L. APPLIES TO OPTIONAL ENCLOSURE
3
INTRODUCTION:
The Sigma 700 Series ‘PDL’ Process Data Logger is a state of the art micro rocessor based, user
configurable instruments for the monitoring and alarming of u to (8) 4/20 MA rocess signals.
The 700 Series PDL erforms the following:
Dis lays information in al ha and numeric format
Allows full user selection of all system variables
Allows user engineering selection
Data logs all variables on user selected interval
Provides USB Port for downloading logs
ORDERING INFORMATION:
Wall Mount Nema 4X Enclosure Sigma 700 Series PDL
SPECIFICATIONS:
ANALOG INPUTS, 4/20MA (8 ea.)
DISPLAY:
LCD, 2 line Al hanumeric, Backlit.
LOOP POWER:
24VDC regulated out ut, 100MA max. (with 110VAC o tion).
3 USER KEYS:
U , Down, Enter
ACCURACY:
0.1% of calibrated s an
LOCKOUT:
User assword, user configurable
INPUT IMPEDANCE:
Voltage 100K, current 100 OHMS
POWER:
24VDC, (110VAC o tional)
ENVIRONMENTAL:
O erating, 0-65° C
Storage, -40° -80° C
R.H., 0-90% non condensing
4
ENCLOSURE:
¼ DIN, ABS lastic 96 X 96 X 110MM or Nema 4X wall mount
FRONT PANEL:
Gasketed Nema 4X Hinged Window
TERMINAL STRIP:
(24) Removable for ease of wiring 28 – 16 AWG
CONNECTIONS:
Removable screw terminal blocks 28 – 16 AWG wire. (27 with 110VAC o tion)
CPU Activity Monitor
PROGRAMMING:
Menu based, all arameters and set oints are user configurable via menu rom ts and user keys.
The reconfigured screens and ‘ ull down’ sub menus with English rom ts assures ra id setu
and commissioning.
1 YEAR WARRANTY
4 M/Byte data logging with USB Port
MODBUS® Master/Slave
Network allows multi le units to be connected together for distributed a lications or remote
monitoring SCADA a lications.
FEATURES:
Micro rocessor Based
LCD Dis lay
3 Function Keys
Isolated 24VDC Sensor Power (with 110VAC o tion)
Fully User Programmable in English
1 Ea. RS485 Port MODBUS® Master/Slave, SCADA
CPU Activity Monitor
5
WIRING DETAIL
See Dwg # 13-14
CAUTION
!
All electrical wiring must be in accordance with all local state and national
codes that apply.
Do not exceed
the rated current of the D.C. power supply (100MA) or the form
’C’ relay outputs (5A/ 40VAC resistive).
WARNING
Hazardous voltages are present within the enclosure. Installation or service
should only be carried out by trained personnel.
6
7
Review Screens
The 700 Series PDL utilizes ‘ lain English’ menu driven screens which are sequential and intuitive.
When the unit owers u , the startu screen will a ear as follows:
After the initial screens have a eared, the unit will show the ‘MAIN SCREEN’ which scrolls as
shown below.
NOTE: To pause the screen scroll, press the
buttons.
PROGRAMMING SCREENS
From the Main Menu, Press the button to access the Password Screen:
Software Version #
Identifies the unit
Function and Version #
Shows in uts 1 – 4
with selected
engineering unit and
current value.
Shows in uts 5 - 8
with selected
engineering unit and
current value.
8
se the buttons to enter the re rogrammed assword, then ress to advance to the Menu
Screens.
Use the buttons to advance to the ‘Scaling’ screen.
Press to advance through all in ut screens and when com lete, the controller will save all changed
values and return to the Main Screen.
Use the buttons to enter the dis layed value for channel 1 low. NOTE: Numbers will change faster
with the key held down.
Move to Screen 2
Press to advance to channel 2 settings.
Continue with setting channels 2 – 8 in the same way as described.
And return to the Main Screen.
ADVANCE TO THE ‘SETUP’ MENU’
Setu screen rovides ‘global’ arameters, which affect overall erformance and o eration.
PASSWORD SCREEN
Dis lay shows
that a value of
4MA will
dis lay .00
Shows that a value
of 5.00 will be
dis layed with an
in ut of 20MA.
Show Channel 1
In ut Low Value
Scaling screen allows
user rogramming of all
channels in engineering
units.
9
Setting a assword ‘Locks’ out unauthorized access to rogram items. NOTE: Please make a note of
the password value if changed. Access to the Menus will be unavailable without the correct
password.
Press to advance to the clock/calendar settings.
Use the buttons to change the month. Press to advance.
Use the buttons to change the year. Press to advance.
Use the buttons to change the other settings as reviously described.
Press to advance to the log interval time settings.
NOTE: This screen allows for setting the log interval. As shown the unit will take a reading every 5
seconds.
10
Logging may also be started and sto ed by connecting a dry contact between DI1 and digital
common. It is necessary to remove the screen anel to access this terminal block. Logging
occurs whenever these oints are closed.
Press to advance to the NODE screen. This allows selection of the unit NODE number when used in
MODBUS Network.
Press to advance to the in ut filter screen.
THE DIAGNOSTIC SCREEN
The final menu item is ‘DIAGNOSTICS’. This screen rovides real time information about the current
status of both in uts and out uts.
NOTE: Only digital in ut (1) is used in the 700MM.
This is the Relay
Out ut status.
Shown is Relay
1 and Relay 2
Active. The 8
in uts are shown
the same way.
NOTE:
Use the
in ut filter to
“dam en” noisy or
bouncing values.
NOTE:
No relays in
Data logger.
Inhaltsverzeichnis
