SignalGuys SSPT724A Bedienungsanleitung

SSPT724A Timer Quick Start Guide

Open timer enclosure and remove mounting parts and instructions.

When ready to program the timer, plug in timer to 120 Volt Ac power receptacle

Press the SET button to reach the “Press Enter to Set Time”then press Enter

Pressing Enter begins the curser scrolling the positions available for entry.

Set the Date and the current time—NOTE: All times need to be expressed in

Military 24 hour time (i.e. 3PM is 15:00)

Press the Set button to reach the “Press Enter to Set BK (Block)”then press Enter

Pressing Enter begins the curser scrolling the positions available for entry.

Set the Block for the days of the week you need the timer to sound the horn (i.e.

Monday and Friday for Monday through Friday—make sure your first day begins

your week and follows to the end of your week—do not set the Block for Saturday

and Sunday for instance because that is ONLY Saturday and Sunday. A full 7 days

should be Monday and (through) Sunday. Time=DS simply allows for Daylights

saving time adjustment and can be left at DS if desired.

Press the Set button to reach the “Press Enter to Set Evnt (Event)”then press Enter

Pressing Enter begins the curser scrolling the positions available for entry.

Event numbers begin at 01 and move up during subsequent event programming.

The entry position to the right of the ^ MUST be set for PL (pulse) for all events

you set.

The position further to the right is the duration the horn will sound—you can set

this from 1 to 15 seconds.

The next position is the Day of the week—this MUST be SET for BK to refer the

timer back to the Block of days you set above.

And finally the time for the event, Must be set in Military time as necessary. (i.e.

Lunch at 1:30 PM should be set in Military time as 13:30)

Continue this process to set all of your time events.

When finished press SET or leave the timer alone and it will return to the main screen.

The screen reports the current status of the RELAY and generally it will always say Relay

OFF until the vent time is reached and the Relay changes for that short period of time (1

to 15 seconds depending on your event setting).

Once programming is complete, your Electrical Professional can connect the horns, etc.

using acceptable practices as per the NEC.

Overview:

The SignalGuys.com Start/Stop Work Timer SSPT724A is an extremely versatile 24 Hour 365 Day Event Timers designed to

support a wide range of applications. Such applications include: Start/Stop Work Time, Home and Building Automation,

Security, Lighting Control, Etc. The PT724A timer board is equipped with an independently controlled form “C” relay contact

that provides many latching and/or momentary operations during a program schedule of your choice. The EE prom memory

allows for programming of unit prior to/or during field installation. Events may be set for single or multiple operations

on a daily and/or weekly schedule. The block programming feature enables repeating an event on any combination of

consecutive days. PT724A will compensate for daylight savings time if desired. Individually select-

ed holiday exceptions can be programmed to over-ride regularly scheduled events.

Specifications:

• 120volts AC operation as wired from Factory.

• Standby current: 10mA (relay off) 50mA (relay on).

• Form “C” relay contacts are rated 10amp @120VAC/28VDC-factory wired for 120 Vac output on contact closure.

• EE Prom memory protects against loss of programming due to power failure.

• Accurate crystal controlled clock.

• Momentary and/or Latching Events.

• 50 individually programmed daily/weekly events.

• Block programming capacity can accommodate a total of 350 events per week.

• 10 programmable Holiday dates.

• “First man in” option.

• Alphanumeric LCD display simplifies programming.

•Standard or Daylight Savings Time settings.

• Automatic compensation for leap year.

• Lithium battery backup optional --maintains clock.

Enclosure Dimensions (approximate): 7.5”H x 7.5”W x 5”D

Installation Instructions:

1. Mount Unit in desired location.

Carefully Review:

Basic Operation (pg. 2-3)

Terminal Identification Table (pg. 3)

Push Button Layout and Description(pg. 3)

Programming Instructions (pgs. 4-6)

2. Connect 120 volts AC using AC power cord, or hardwire as desired..

3. Do Not Connect 12VDC battery (optional, for unique applications) to terminals marked [+ BAT -- 12VDC].

4. Lithium battery is optional--purchase battery 2032 locally--only maintains clock time during a 120 vac power loss.

5. Connect horn to be controlled to the 120 Volt AC outputs labeled "120 Vac Out"-- white and black wire with butt splices.

Note:The device is wired for 120 Volt AC output to Horns, etc, When DC powered electromechanical devices such as

Mag Locks, Electric Strikes, Relays, etc. are to be installed, install a catch diode across the pos (+) and neg (-) terminals

of the device. Connect diode as close to the device as possible with the banded side facing the pos (+) terminal.

This will reduce interference. Remove the factory installed 120 VAC connections to the N.O. and Common terminals.

6. Program clock and desired event schedule (see programming instructions pg. 4-6).

Basic Operation:

PT724A controls an independently operated dry form “C” relay output. Relay can be programmed

to: turn on (latch), turn off (release latch) or pulse (momentary toggle), the PULSE is used for start stop work timer applications

at a specified time and day (this is referred to as an event). Events are programmed via the push buttons and LCD display.

Events may be programmed to occur on any day of the week at any time. In addition, events may be repeated at a specific

time on two (2) or more consecutive days (i.e. M-F, Sun-Th, etc) Multiple combinations of individual and block events

may be programmed. Holiday exceptions are individually selected by date and will over-ride all regularly scheduled events.

- 2 -

Push Button Description Table:

Push Button Function/Description

SET Scrolling keys for programming. Escaping out of existing programming.

ENTER Accepts selections made to programming.

UP Scrolls through selections.

DWN Scrolls through selections.

UP and DOWN keys can be used to select data entries. After scrolling to the correct entry, depress ENTER to accept.

The four (4) output relay modes consist of:

Relay OFF - De-energizes the relay until a relay ON event is detected

Relay ON - Energizes the relay until a relay OFF event is detected.

Disable - Used to cancel an existing programmed event.

**Start/Stop Work Applications*** PULSE - Momentarily energizes the relay for a selectable time period of 1 sec. to 15 secs.

Time is displayed in 24 hr. military format.

Terminal Identification Table:

Terminal Legend Function/Description

NO, C, NC Dry Contact output used to switch controlled devices. When these relays are energized (ON)

the NC and C terminals are open and the NO and C terminals are closed. When this relay is

de-energized (Off) the NC and C terminals are closed and the NO and C terminals are open.

+ DC -- AC or DC Input 12 to 24 volt. When using DC carefully observe polarity. This is already wired.

~ AC ~ to the transformer by the factory--no changes are required-standard use

+ BAT -- 12VDC standby battery input (battery leads provided). Rare applications for this option

12VDC

FM When this terminal is connected to DC neg. (-) the “First Man in” feature is enabled.

The relay will remain in its present position until this connection is terminated.

At that time the relay will resume normal operation and latest scheduled events will occur.

- 3 -

SET ENTER UP DWN

BAT ---

12VDC

DC ---

NO NCC

RELAY ON

SU 01:01

}

Lithium Battery Socket

(2032) optional

Fig. 1

DC Power Supply

Factroy Installed

Push Button Layout

Programming Instructions:

A. Setting Clock/Calendar:

Upon initial power up RLY OFF

SU 01:01

Depress SET ENTER to

SET TIME

Depress ENTER 01/01/01

SU/01:01

Enter the current date, day of week and time (military) by depressing UP and DWN to make the selection then

depress ENTER to accept.

Next select either DS (daylight savings mode) or ST (standard time mode) by depressing set until

ENTER to

SET BK

Depress ENTER to scroll until flashing cursor appears under DS (daylight savings mode) in display. To change

mode depress UP or DWN once ST (standard time mode) will appear in display. Depress ENTER to accept

correct selection.

Note: The flashing cursor denotes location of data entry selection to be made. If an entry was made in error or

requires changing, depress SET to backspace, make the correct selection and depress ENTER to accept

data and advance the cursor.

To change or program clock/calendar simply repeat the steps above.

B. Setting Events:

Depress SET until ENTER to

SET EVENT

Depress ENTER #01 OFF

SU 00:00

Depress ENTER until the flashing cursor appears under OFF in display. Now select type of event required, by

scrolling using the UP and DWN push buttons until either:

ON - Relay ON (latching mode).

OFF - Relay OFF (latching mode).

PL - Relay Pulse ( momentary).

appears in display and depressing ENTER will make selection.

When selecting the pulse mode PL01 will appear in the display. It is now necessary to assign the length of time

(duration of relay activation). The pulse can range in length from 1 second minimum to 15 seconds maximum

and is selected by using UP or DWN push buttons, then depressing ENTER to accept.

Note: If pulse duration is not selected relay output defaults to 1 second.

Next select the day of the week and time (military) by scrolling using UP and DWN push buttons and depress

ENTER to accept. If you set a BLOCK of days (i.e. Monday thru Friday)--select BK at this point--NOT a day.

You may continue to program events by repeating the previous steps or exit programming by depressing SET.

Note: When programming additional events it is necessary to select the next consecutive event number following

the last event program to continue.

Note: When it is required to have the same event repeated on two (2) or more consecutive days of the week

(Block Programming), enter the first day followed by the last day by depressing SUN through SAT.

Example:

1) Monday through Thursday depress MON followed by THURS.

2) Wednesday through Sunday depress WED followed SUN.

- 4 -

will appear in display.

appears in display.

will appear in display.

- 5 -

C. Setting Block Events (weekly repeat):

Depress SET until ENTER to

SET BK

Depress ENTER BK=SA/SU

TIME=DS

Flashing cursor will appear at the location of the first day of the week desired. Depress UP and DWN to

select day. Depress ENTER to confirm selection, then cursor will appear at the location of the last day of the

week desired. Depress UP and DWN to select day. Depress ENTER to confirm selection. Depress ENTER

again to escape. As an example: Monday and then Friday-- for a work week setting.

D. Setting Holiday Events:

Depress SETuntil ENTER to

SET EVENT

Depress ENTER #01 ON

HL 00:00

Next select HL to indicate as holiday event and time by scrolling using UP and DWN push buttons and

depress ENTER to accept.

You may continue to program more holiday events by repeating the previous steps or exit programming by

depressing SET.

E. Setting Holiday Dates:

It is now necessary to assign these holiday events specific calendar dates which they are to occur.

To select Holiday events depress SET until

ENTER to

SET HOL

Depress ENTER #01 HOL

SU 00:00

Note: Holiday events will override all regularly programmed events.

F. Delete/Disable Events or Edit Events:

Previously programmed regularly scheduled and/or holiday events may be deleted/disabled without having

to erase all events.

Depress SET until ENTER to

SET EVENT

Depress ENTER #01 ON

TU 00:00

Now scroll using UP and DWN push buttons to the event you wish to delete, depress ENTER to move

flashing cursor under relay option then depress UP and DWN push buttons until DIS is displayed, depress

ENTER to confirm appears in display .

appears in display.

will appear in display.

appears in display.

- 6 -

G. Delete All Events:

All previously programmed events can be deleted by depressing

SET until ENTER to

CLR MEM

Depress ENTER CLEAR

MEMOR

Depress ENTER PRESS UP

& ACCEPT

Depressing UP push button will now clear all events previously programmed.

If you wish to escape from this selection depress any of the other push buttons: SET,ENTER and DWN.

PT724AE

Enclosure Dimensions:

8.5”Hx 7.5”W x 3.5”D

3.63"

1.25"

7.25"

2.25" 0

3.5"

1.13"

.625" 6.75"

3.5"

3.63"

2.25"

3.5" 0

LEFT RIGHT

BACK

TOP ONLY

appears in display.

will appear in display.

Inhaltsverzeichnis

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung