SignWarehouse.com Vinyl Express Cougar 24" Bedienungsanleitung

ValueCut 24”

Vinyl Express Cougar 24”

Owner’s Manual

Table of contents

1. Safety precautions…………………………………………………………….……….….1

2. Standard accessories…………………………………………………………………..….3

3. Install machine…...5

3.1 Installation and connection………………………………………………….…. .…....5

3.2 Install cutting tool…………………………………………………………….…...….6

4. Interface features……………………………………………………………….…. .…….7

5. Cutter operating instructions……………………………………………………………. .9

5.1 Name and functions of parts…..………………………………………………………9

5.2 Basic operation…...11

5.3 Operating instructions……………………………………………………….…..……14

5.4 Technical features…………………………………………………………….….……21

6. Troubleshooting……………………………………………………………… . . .…….…22

metric -> imperial

1 millimeter [mm] 0.03937 in

1 centimeter [cm] 10 mm 0.3937 in

1 meter [m] 100 cm 1.0936 yd

imperial -> metric

1 inch [in] 2.54 cm

1 foot [ft] 12 in 0.3048 m / or 30.48 cm

1 yard [yd] 3 ft 0.9144 m / or 91.44 cm

1．Safety precautions

USER MANUAL Safety precautions

Definition of symbols:

WARNING! Improper operation may result in personal

injury or damage of equipment.

May cause electric shock if improperly handled.

Do not attempt to repair machine as damage may occur.

Personal injury or electric shock may result.

Do not use a power source that does not meet required

voltage. Fire or electric shock may result.

Do not leave machine on if it emits smoke, an unpleasant

odor, or unusual noise. Turn off immediately.

Do not unplug the machine when the power is on to avoid

damage.

Make sure the machine is grounded to prevent electric

shock or damage.

Safetyprecautions USER MANUAL

Do not drip liquid or drop metal parts into the

machine. May result in fire or electric shock.

Do not touch the blade tip with your finger to

prevent injury or damage to blade head.

Do not excessively bend, pull or weigh down

power cord. May result in fire or electric shock.

Do not leave power cord plugged into socket

when machine is not being used for a long

period of time to prevent damage.

Do not place hands into machine during

operation to avoid injury.

Place the machine on a stable surface to prevent

damage from sliding or falling.

Unplug the machine by pulling the power cable

plug, not cord, to prevent cable damage.

Never operate the machine during a lightning

storm as a power surge could damage it.

USER MANUAL Standard accessories

2．Standard accessories

Please check the following accessories after unpacking, contact customer service if you find

anything missing.

Serial

No Item Quantity Icon

1 Power cable 1

2 Serial cable 1

3 Blade holder 1

4 High-speed tungsten

steel blades 3

5 Media cradle

(for desktop machine) 1

Standardaccessories USER MANUAL

Vertical stand and installation diagram

(Available to the type with minimum width of 1000mm only)

Unpack the parts of the stand. Locate and open the parts bag. Assemble the stand according to the

diagram. After assembly, place the cutter on stand. Align screw holes and fasten to stand with screws.

USER MANUAL Basic operation

3．Basic operation

3.1 Installation and connections

WARNING! Improper operation may result in personal injury or

damage of equipment.

Make sure the machine is grounded to prevent electric shock or

damage.

Do not use a power source that does not meet required voltage. Fire

or electric shock may result.

Do not unplug the machine when the power is

on to avoid damage.

Place the machine on a stable surface to

prevent damage from sliding or falling.

3.1.1 Place the cutter on a flat, stable surface.

3.1.2 Connect the serial cable to the COM1 or COM2 port on the cutter and the computer.

3.1.3 Place the media cradle (for desktop cutters) behind and parallel to the cutter.

3.1.4 Check the voltage of the power source and make sure it is grounded. Do not connect the

machine until this step has been completed.

3.2 Installation of blade

WARNING! Improper operation may result in personal injury or

damage of equipment.

Do not touch the blade tip with your

finger to prevent injury or damage to

blade head.

3.2.1 Fit cutter into the rotary tool, as shown in the following illustrations:

(outside view) (enlarged view)

3.2.2 Adjust the length of the blade as required for specific media.

Blade length screw Blade handle Blade Blade holder

Basicoperation USER MANUAL

Vinyl

surface

Base paper

Correctbladelength Blade depth too long Blade depth too short

3.2.3 (1) Loosen the screw on the blade handle.

(2) Assemble the tool with blade into the tool

carrier.

(3) When the tool is in the appropriate position gently

tighten the blade holder screw.

4．Interface features

USER MANUAL Interface features

The cutter comes with a serial RS-232 input interface, which is connectable to a wide range of

computers.

A properly connected interface cable will enable the cutter to accurately respond to plotting

and engraving commands from the computer. Improper connection of the cable may cause machine

difficulty and lock up.

RS-232 Serial Interface:

RS-232 Serial Interface meets features of ELA (Electric Industries Association).

General features:

Standard:CCITTV14，EIA RS-232C，JIS×5101

Baud rate: 300, 600, 1200, 4800, 9600baud

Stop bit: odd/even/none

Word length: 8bit

1 2 3 4 5 6 7 8

Start bit data bit check bit stop bit

RS232C foot definition：

Sign

SYS RS232C CCITT

Signal

Dissection

1 FG AA 101

2 SD BA (TDATA) 103 ← P

3 RD BB (RDATA) 104 → P

4 RS CA (RTS) 105 ← P

5 CS (CTS) 106 → P

6 DR (DSR) 107

7 SG AB (SGND) 102

8-19

20 ER CT ( ) 108 ← P

21-25

Interfacefeatures USER MANUAL

Electric parameters：

RC，SD RS，CS，DS，ER

Negative Positive logic

Input

voltage

level

+5v to +12v

-5v to -12v

Logical “0”

Logical “1”

“ON”

“OFF”

Input

voltage

level

+5v to +12v

-5v to -12v

Logical “0”

Logical “1”

“ON”

“OFF”

Connector:

Cuttingplotterport:DB-25S

Signalcomputerport:DB-25P

Map of serial interface cable connecting between IBM-PC computer and cutting plotter。

Cuttingplotterport Signalcomputerport

Signal Foot Foot Signal

Chassis GND

Signal GND

RX Data

TX Data

RTS

DTR

Chassis GND

RX Data

TX Data

GND

RTS

DTR

（DB25B）

（DB25P）

N/C

（DB9P）

N/C

Shield

Signa GND

TX Data

RX Data

CTS

DCD

DSR

Shield

TX Data

RX Dats

GND

RTS

CTS

DTR

DSR

Inhaltsverzeichnis

Andere SignWarehouse.com Cutter Handbücher

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com enduraCUT 2 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung

Guarda

Guarda EDGE Bedienungsanleitung