SIIG 4000-MT Bedienungsanleitung

FiberOptic Switches

Quick Installation Guide

This quick installation guide provides instructions for installing a

FiberOptic Switch.

1-1 Introducing the FiberOptic Switches

SIIG's line of fiber optic switches are standard switches that meet all

IEEE 802.3u/802.3X standards. A Fast Ethernet Switch is a cost-

effective solution for easing your network congestion problems on

existing shared-hub network by breaking up the collision domain

and by multiplying the network performance. The overall network

transmissionspeedisincreasedandthenetworkefficiencyisimproved

to accommodate high-bandwidth applications, such as imaging

multimedia, and CAD/CAM, etc.

The following models are available :

• FiberOptic Switch 4000-ST (4 ST fiber ports )

• FiberOptic Switch 4000-SC (4 SC fiber ports)

• FiberOptic Switch 4000-MT (4 MT-RJ fiber ports)

• FiberOptic Switch 8020-ST (8 TP & 2 ST fiber ports)

• FiberOptic Switch 8020-SC (8 TP & 2 SC fiber ports)

Features/Specifications

•Standards: IEEE 802.3u and 802.3x 100Base-FX

•Transmission Mode: Full or Half-duplex

•Transmission Speed: 10/100Mbps for TP ports

100Mbps for fiber ports

•Packet Forwarding/Filtering Rate: 148,000 packets/sec full

wire rate on 100Mbps forwarding and filtering. 14,880 packets/

sec full wire rate on 10Mbps forwarding & filtering

•MAC Address and Self-learning: up to 12K

•Buffer Memory: 1024KB

•Flow Control: IEEE 802.3x compliant for full-duplex;

Back pressure flow control for half-duplex

04-0184A

• Network Interface:

Models:

4000-ST : Four 100Base-FX, ST (multi-mode)

4000-SC: Four 100Base-FX, SC (multi-mode)

4000-MT: Four 100Base-FX, MT-RJ (multi-mode)

8020-ST: Eight 10/100Base-TX; RJ-45

Two 100Base-FX, ST (multi-mode)

8020-SC: Eight 10/100Base-TX; RJ-45

Two 100Base-FX, SC (multi-mode)

•Fiber Optic Connector:

ST/SC/MT-RJ connector (multi-mode), Tx/Rx

•Fiber Optic Cable and Maximum Length:

50/125, 62.5/125 or 100/140 µm (multi-mode); up to 2000 m

•TP Connector: (For models 8020-ST and 8020-SC only)

•Selectable Duplex Mode Switch: Per fiber port FDX/HDX

DIP switch

•LED Indicators:

LED Color Function

Link/Act Green Lit when remote device connection is good

Blinks when any traffic is present

100Mbps Green Lit when 100Mbps speed is active

FDX/Col Amber Lit when full-duplex mode is active

Blinks when collision signal is present

POWER Green Lit when AC power is ON and good

•Power Requirement:

AC Voltage: 100~240V

Frequency: 50~60Hz

Consumptions: Models 4000-ST/SC/MT: 25W Max.

Models 8020-ST/SC: 43W Max.

•Operating Temperature: 32° to 122° (0° to 50°C)

•Storage Temperature: -40° to 158°F (-40° to 70°C)

•Relative Humidity: 5% to 90%, non-condensing

•Dimensions:

Models 4000-ST/SC/MT: 45mm (H) x 330 (W) x 200mm (D)

Models 8020-ST/SC: 46mm (H) x 440 (W) x 220mm (D)

Maximum Fiber Optic Cable Lengths

Tohelpensureasuccessfulinstallation,youmustobservethefollowing

cabling parameter. Violating these rules can render the LAN to work

poorly.

Full-duplex Switch via Fiber:

Multi-mode Node to Node: 2000 m

Node to Hub 2000 m

Hub to Hub: 2000 m

Half-duplex Switch via Fiber:

Multi-mode Node to Node: 412 m

Node to Hub 412 m

Hub to Hub: 412 m

Half-duplex Class II Hub via Fiber:

Multi-mode Node to Node: 205 m

Node to Hub 100 m

Hub to Hub: 5 m

Maximum TP Cable Lengths

Tohelpensureasuccessfulinstallation,youmustobservethefollowing

cabling parameter.

Category 5 UTP Cable:

Multi-mode Node to Node: 100 m

Hub to Hub: 100 m

* For connection to Router, Bridge, or regular 100Base-X Hub,

please refer to the device's Technical Manual for respective

bit-time delay.

Unpacking

Before installing your FiberOptic Switch, verify that the following

items are included in the packaging carton:

• FiberOptic Switch

• Mounting accessory (for 19" rack shelf)

• AC power cord

• This Quick Installation Guide

Please notify your dealer if any item is damaged or missing.

2-1 Hardware Installation

Thefollowingfiguresidentifythefrontpanelport,DIPswitchandLED

locations for the FiberOptic Switch models. Please refer to the appro-

priate diagram for your model.

4-Port FiberOptic Switch 4000-ST/SC

4-Port FiberOptic Switch 4000-MT

8-Port FiberOptic Switch 8020-ST/SC

1/MPR 2345678

1/DT E

FDX

HD X

A B

Link /

100M

PO W

Link /

100M

FD C

10 / 1 00 S wi tc hi ng

Hu b

DIP

Switches

LEDs

ST/SC Fiber Ports

100Base-FX

1/MPR Port

TP RJ-45 Ports

10/100Base-TX

LEDs DIP

Switches

"! "!

6 :   4: 6 :   4: 6 :   4: 6 :   4:

., :

0,:

Link/A ct

100M bps

FD X/Col

PO W ER

1 2 34

Fa st Eth er net S wit chi ng Hu b

ST/SC Fiber Ports

100Base-FX

"!

., :

0,:

 !"

Link/Act

100M bps

FD X/Col

PO W ER

1 2 34

Fa st Eth ern et Swi t chi ng Hub

DIP

Switches

LEDs MT-RJ Fiber Ports

100Base-FX

2-1.1 Fiber Port Full-/Half-duplex Mode Configuration

Eachfiberportcanbeindependentlyconfiguredforeitherfull-duplex

(FDX) or half-duplex (HDX) mode through DIP switches located on

the front panel. The default setting is Full-duplex.

• Verify that the duplex mode setting for each fiber port on

the Switch hub matches the connected remote device's mode

setting (full-duplex to full-duplex, half-duplex to half-duplex).

• The number on the DIP switch corresponds to the fiber port

number it sets.

To change a fiber port's mode setting , power down the Switch unit

and set the appropriate DIP switch. Then, power ON to set the new

configuration and status.

Default DIP Switch Settings

2-1.2 Network Device Connections

Proceed with the following steps to make the network connections:

1. Turn OFF the power to the server/host, workstation or any other

device to be connected.

2. Using Fiber Cable for 100Base-FX devices and Cat 5 TP Cable for

10/100Base-TX devices, connect each device to the appro-

priate fiber/RJ-45 ports on the Switch hub .

NOTE FOR FIBER CONNECTIONS: When connecting fiber

cable, you must make a paired connection to each fiber port.

Connect a cable between the selected Switch port's Tx (transmit)

port and the remote device's Rx (receive) port. Connect another

fiber cable between the Switch port's Rx (receive) port and the

device's Tx (transmit) port.

Tx/Rx Fiber Optic Cable Connections

FDX

HDX

FDX

HDX

Models 4000-ST/SC/MT Models 8020-ST/SC

Remote

Device

Tx Rx

Switch Hub

Tx Rx Tx Rx Tx Rx

A B

NOTEFORMODELS8020-ST/SC:Thefiberportcanbeup-linked

to an upper level hub's port. You may use the "1/MPR" port to

up-link the hub to an upper level hub's TP port. Only one up-link

is allowed between any two hubs.

3. Plug the female end of the AC power cord into the receptacle

on the back of the Switch unit. Plug the other end into an AC

power source.

NOTE: 4000-ST/SC models will automatically power ON when

plugged in. The 8020-ST/SC models provide a ON/OFF switch

control on the back of the unit.

2-1.3 Switch Hub Cascading & Long Haul Connections

Theoretically, the switch hub breaks up the collision domain in hub

cascading so you may unlimitedly up-link the hubs. However,

in practice, the network extension (cascading levels & overall

diameter)islimitedbythetimingrequirement(time-outspecification)

of your application software and network operating system.

The sum of all elements' bit-time delay and the overall bit-time delay

of wires/devices must be within 512 bit in a 100Base-X network

segment (collision domain). The TP, fiber cables and devices' bit-time

delay (round trip) is as follows:

100Base-TX 100Base-FX

DTE↔DTE: 100 DTE ↔DTE: 100

Cat. 5 TP Wire: 1.112/m Fiber Cable: 1.0/m

DTE FX to DTE TX: 100

100Base-TX to 100Base-FX Converter: 56

Multiple Hubs Cascading and Long-Haul Connection

3-1 Troubleshooting

Network troubleshooting requires patience and logic. Generally

speaking,thecablingandworkstationconfigurationsarethelikelyfirst

suspects; network hardware is usually last on the list. It is more likely

for an entire hub to fail instead of just a single port.

3-1.1 Cabling Problems

Networktroubleshootingrequirespatienceandlogic.ImproperCabling

is the primary cause of most non-workstation problems on Ethernet

network, particularly for 100 Base-TX and -FX networks. It must be

emphasized that genuine twisted-pair cable and fiber optic cable be

used to avoid many types of cabling problems.

• Wiring is definitely the problem if the Link LED does not light.

• Multi-mode fiber cable should match the switch’s fiber

transceiver. Flat telephone extension cables or Cat. 3 wires sold

at electronics stores are not the same as Cat. 5 twisted-pair

cable and will not work in 100Mbps network.

Level 2 Fiber

1/MPR 2

34567

1/DTE

FDX

HDX

A B

Link/

100M

POW

Link/

100M

10/100 Swit ching

1 2 3 4 5 6 7 8

Long Haul I ntra-hub connection

Level 2 4 Port Fiber ST/SC Switch

"!  "!

6 : 4 : 6 : 4 : 6 : 4 : 6 : 4 :

.,:

0, :

Li nk

FDX

WE R

1 2

Fa s t E t he r n et S w it ch in g H ub

File Server

"!  "!

6 : 4 : 6 : 4 : 6 : 4 : 6 : 4 :

.,:

0, :

Li nk

FDX

WE R

1 2

Fa s t E t he r n et S w it ch in g H ub

Level 1 4 Port Fiber ST/SC Switch

Level 2 Fiber Switch

3-1.2 Workstation Problems

Mostnon-cabling problems result from improperconfiguration of the

networkinterfacecard(NIC)anditscorrespondingdriver.Thefollowing

points will be helpful:

• Like other add-on cards in the workstation or server, NIC must

have unique memory address, I/O address, and interrupt. The

settings on a particular card must not conflict with the settings

on any other card in the same station. Please refer the User’s

manual of the NIC, computers, and Networking operating

systems to determine the proper configuration.

• The selection of half or full duplex, the speed of 10 or 100Mbps

for the NIC setting must match the mode and speed setting of

the corresponding port of the Hub. For NWay Auto-

Negotiation setting, both link partners will auto-adjust to the

highest allowable speed and mode operation.

• If a workstation (workstation A) does not work and other

100Base-X ports on the hub are functioning, remove a fiber/

RJ-45 plug from a functioning port with a functioning

workstation (workstation B) and insert it into the suspect port.

If workstation B still works, the problem is in workstation A or

in the wiring. However, if workstation B does not work, then

the hub may have a defective port. Even if you suspect a

defective port on the hub, continue testing. Improperly wired

workstations may appear to be functional, especially if they are

located near the hub. Sometimes, a port connected to an

improperly wired workstation can function marginally while

another port may not work at all.

• Once you have established that the hub is working properly,

check all wiring between the hub and the malfunctioning

workstation. Ensure that the transmit and receive wires have

not been crossed; the two transmit wires should be paired

together as should the two receive wires.

• Use a continuity checker to ensure that wires do not have

breaks. By shorting together the two wires of a pair at one end,

you can use the continuity checker at the other end. Also, check

that there are no shorts between wires.

3-1.3 Other Problems

OtherspecificproblemsmaybediagnosedbyusingtheLEDs,asbelow.

Power LED is off when the AC Power switch is ON:

• Defective power supply unit or fuse

• Incorrect AC voltage

• Defective Hub

Link/Act LED is off at any Fiber/TP port:

• Faulty node or wiring connection.

For fiber: the “TX”, “RX” cables should be paired at both ends

For TP: a clicking sound should be heard when the RJ-45

plug is inserted in the STP RJ-45 jack

• No Link signal is received from the remote node/site

100Base-X Port at irregular traffic:

• Abnormal or invalid transmission status (mode / speed)

between local and remote link partners, i.e., full-duplex port is

connecting to a half-duplex port, or 10Mbps port is connecting

to a 100Mbps device.

Hub does not work:

If the hub does not work or is experiencing interference (e.g., your site

maybelocatednearradiostationortransmitter,etc.),tryusingshielded

twisted-pair (STP) cable instead of UTP cable.

Hub Diagnostic Test

• The switch hub performs a self-diagnostic test at major hub

modules upon power on, LED indicators will go to normal

status if no problem occurred.

• To reset or restart the hub, power off the hub and wait for 10

seconds, then power on it again.

4-1 Technical Support & RMA

Questions? SIIG’s On-line Support has the answers! Simply visit

ourwebsiteat

www.siig.com

andclickontheON-LINE SUPPORT

icon for instant technical support. You may also e-mail us on-line

at: http:\www.siig.com/technical_support_form.html

If you need additional help, Tech Support Specialists are available

from 8:00 a.m. to 5:00 p.m. Mon. – Fri., PST at (510) 353-7542.

In order for SIIG’s Technical Support to give you prompt service,

you will need the following information.

Part Number: ______________________________________

Computer Configuration: ___________________________

Return Merchandise Authorization (RMA)

SIIGwarrantstotheoriginalbuyeroftheproductthatthehardware

is free of defects in materials and workmanship for a period of five

years from the date of purchase. If your product fails to be in good

workingorderduringthewarrantyperiod,youmayreturnittoSIIG

for repair or replacement at SIIG's option. To return a product:

Step 1: Call SIIG's RMA Department

CalltheRMADepartmentat(510)413-5333foraReturnMerchandise

Authorization (RMA) number. To get a RMA number, you must

haveyourproduct serialnumber. Theserial numberis locatedon

the side of the box it came in and on the back of the product.

Step 2: Complete the RMA form

• Fill out the RMA form and include it with the product.

• Properly pack the product for shipping. All software, cable(s) and

accessories that came with the original package must be included.

• ClearlywriteyourRMAnumberonthetopofthereturnedpackage

andontheaccompanyingRMAform.SIIGwillrefuseanyshipping

package, and not be responsible for a product returned without

a RMA number posted on the outside of the shipping carton.

Step 3: Ship the product

You are responsible for the shipping cost to SIIG at the following

address: SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIG will ship the repaired or replaced product via UPS Ground or US

Mail at no cost to you.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIIG Schalten Handbücher

SIIG

SIIG JU-SW2212-S1 Bedienungsanleitung

SIIG

SIIG SuperSpeed USB 4-Port Hub Bedienungsanleitung

SIIG

SIIG CE-KV0011-S1 Bedienungsanleitung

SIIG

SIIG AV-GM09V3-S1E Bedienungsanleitung

SIIG

SIIG MultiView CE-H26311-S1 Bedienungsanleitung

SIIG

SIIG JU-H42B22-S2 Bedienungsanleitung

SIIG

SIIG CE-H21112-S1 Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 4-Port Bay Hub Bedienungsanleitung

SIIG

SIIG CE-KV0G11-S1 Bedienungsanleitung

SIIG

SIIG CE-CM0011-S1 Bedienungsanleitung

SIIG

SIIG USB 3.0 Bedienungsanleitung

SIIG

SIIG CE-000012-S1 Bedienungsanleitung

SIIG

SIIG JU-SC0211-S1 Bedienungsanleitung

SIIG

SIIG JU-SW2212-S1 Bedienungsanleitung

SIIG

SIIG FireWire Bedienungsanleitung

SIIG

SIIG SlimHub 4000P Bedienungsanleitung

SIIG

SIIG AV-GM04P3-S1 Bedienungsanleitung

SIIG

SIIG DisplayPort 2-Port KVM Switch Bedienungsanleitung

SIIG

SIIG 2x1 USB DisplayPort KVM Switch with Remote... Bedienungsanleitung

SIIG

SIIG CE-KV0612-S1 Produktinformationsblatt

SIIG

SIIG AV-GM09M3-S1 Bedienungsanleitung

SIIG

SIIG PC Switch 6000 Bedienungsanleitung

SIIG

SIIG US22 Series Bedienungsanleitung

SIIG

SIIG ID-SC0511-S1 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung