Silent Call Communications CO5-SS Bedienungsanleitung
CARBON MONOXIDE DETECTOR
WITH BUILT IN WIRELESS TRANSMITTER
Installation and Operation Manual
Model # CO5-SS
418 MHZTRANSMITTER
Document #
1081823126052
GENERAL INFORMATION:
Before installing detectors, please thoroughly read these installation
instructions. For detailed information on detector spacing, placement,
zoning, wiring, and special applications refer to current edition of the
NFPA 72 National Fire Alarm and Signaling Code.
NOTICE: These instructions should be left with the owner/user of this
equipment.
IMPORTANT: This detector must be tested and maintained regularly
following NFPA 72 requirements. Test detector operation weekly. The
detector should be cleaned at least once a year.
NOTE: CO Detectors have a limited life. CO detectors should be replaced
immediately if not operating properly. You should always replace a CO
detector after 6 years from date of purchase.
NOTE: Remove battery tab before installation.
NOTE: Radio Frequency device operates at 418MHz
WARNING: This product is intended for use in ordinary indoor
locations of family living units. It is not designed to measure
compliance with Occupational Safety and Health Administration (OSHA)
commercial or industrial standards. Individuals with medical problems
may consider using warning devices which provide audible and visual
signals for carbon monoxide concentrations under 30ppm.
FCC ID: PPJCO5SS418
WHAT TO DO IF THE CARBON MONOXIDE DETECTOR GOES INTO
ALARM:
WARNING:
Activation of your CO alarm indicates the presence of Car-
bon Monoxide (CO) which can KILL YOU. If Alarm sounds:
1. Operate reset/silence button;
2. Call your emergency services (_____________________)
(re department or 911);
3. Immediately move to fresh air-outdoors or by an open
door/window. Do a head count to check that all persons
are accounted for. Do not re-enter the premises nor
move away from the open door/window until emergen-
cy services responders have arrived, the premises has
been aired out, and your alarm remains in its normal
condition.
4. After following steps 1-3, if your alarm reactivates with-
in 24 hour period, repeat steps 1-3 and call a qualied
appliance technician(________________) to investigate for
sources of CO from fuel burning equipment and appli-
ances, and inspect for proper operation of this equip-
ment. If problems are identied during this inspection
have the equipment serviced immediately. Note any
combustion equipment not inspected by the technician
and consult the manufacturers’ instructions, or contact
the manufacturers directly, for more information about
CO safety and this equipment. Make sure that motor
vehicles are not, and have not been, operating in an at-
tached garage or adjacent to the residence.
IMPORTANT INFORMATION FOR THE USER:
CAUTION: This alarm will indicate the presence of carbon mon
oxide gas at the sensor. Carbon Monoxide gas may be present
in other areas.
WARNING: Carbon Monoxide Detector will not operate without
a serviceable battery. Inspect and replace your batteries at least
once a year to ensure proper working condition.
IMPORTANT: Constant exposures to high or low humidity may
reduce battery life. A good safety measures is to replace the
battery at least once a year, or at the same time you change
your clocks for daylight savings time.
WARNING: The installation of this device should not be used
as a substitute for proper installation, use and maintenance of
fuel burning appliances, including appropriate ventilation and
exhaust systems.
Carbon Monoxide Gas and its Detection
This carbon monoxide detector is designed for indoor use only. Do not
expose to rain or moisture. Do not knock or drop the detector. Do not
open or tamper with the detector as this could cause malfunction. The
detector will not protect against the risk of carbon monoxide poisoning
if not properly installed. The detector will only indicate the presence of
carbon monoxide gas at the sensor.
Carbon monoxide gas may be present in other areas. This carbon mon-
oxide detector is NOT:
• Designed to detect smoke, fire or any gas other than carbon monox-
ide
• To be seen as a substitute for the proper servicing of fuel-burning
appliances or the sweeping of chimneys.
• To be used on an intermittent basis, or as a portable alarm for the
spillage of combustion products from fuel-burning appliances or
chimneys
Carbon monoxide gas is a highly poisonous gas which is released when
fuels are burned. It is invisible, has no smell and is therefore impos-
sible to detect with the human senses. Under normal conditions in a
room where fuel burning appliances are well maintained and correctly
ventilated, the amount of carbon monoxide released into the room by
appliances should not be dangerous.
SYMPTOMS OF CO POISIONING:
Carbon Monoxide (CO) is an insidious poison. Carbon monoxide bonds
to the hemoglobin in the blood and reduces the amount of oxygen
being circulated in the body. It is a cumulative poison. Even low levels
of CO have been shown to cause brain and other vital organ damage in
unborn infants with no effect on the mother.
The following symptoms are related to CARBON MONOXIDE POISON-
ING and should be discussed with ALL members of the household:
Mild exposure:
Medium exposure:
Extreme exposure:
Many causes of reported CARBON MONOXIDE POISONING indicate
that while victims are aware that they are not well, they become so
disoriented that they are unable to save themselves by either exiting the
building or calling for assistance.
Also young children and pets may be the first to be affected. You should
take extra precautions to protect high risk persons from CO exposure
because they may experience ill effects from CO at levels that would not
ordinarily affect a heathy adult.
Slight-Headache, nausea, vomiting, fatigue (often
described as “flu-like symptoms).
Severe throbbing headache, drowsiness, confusion,
fast heart rate.
Unconsciousness, convulsions, cardio-respiratory
failure, death.
SOURCES OF CARBON MONOXIDE:
Home appliances used for cooking and heating are the most common
household Carbon Monoxide sources. Vehicles running in an attached
garage can also produce dangerous levels of CO. Burning any fossil fuel
including gasoline, propane, natural gas, oil, and wood can produce
Carbon Monoxide. It can be produced when any heating or cooking
appliance is not installed properly, vented correctly, or malfunctioning.
CO producing appliances include furnace, hot water heaters, gas range/
stove, gas dryer, fuel burning space heaters, generators, vehicles, fire-
places, blocked chimney/vents and grills.
CONDITIONS WHICH CAN RESULT IN TEMPORARY CO SITUATIONS:
1. Excessive spillage or reverse venting of fuel burning appliances
caused by:
i. Outdoor ambient conditions such as wind direction
and/or velocity, including high gusts of wind; heavy air
in the vent pipes(cold humid air with extended periods
between cycles).
ii. Negative pressure differential resulting from the use of
exhaust fans.
iii. Simultaneous operation of several fuel burning applica
tions competing for limited internal air.
iv. Vent pipe connection vibrating loose from clothes dry
ers, furnaces, or water heaters.
v. Obstructions in or unconventional vent pipe designs
which amplify the above situations.
2. Extended operation of unvented fuel burning devices (range,
oven, fireplace, etc.).
3. Temperature inversions which can trap exhaust gases near the
ground.
4. Car idling in an open or closed attached garage, or near a home.
GENERAL DESCRIPTION:
The CO5-SS is a 3V battery powered Carbon Monoxide (CO) detector
with a built in wireless transmitter intended for use with Silent Call
418MHz Signature Series SK2-SS and WC08-SS Receivers.
The detector consists of an electrochemical carbon monoxide sensor
assembly coupled to a wireless transmitter. The transmitter can send
alarm messages to the Silent Call receivers. Refer to the Receiver sys-
tem instructions for the CO alert details. The CO5-SS CO detector will
alert the Silent Call Receiver only during a CO Alarm. Please refer to
Maintenance Section for Low battery and End of Life conditions.
The transmitter signal incorporates a digital addressable coding system
that is preset at the manufacturer.
IMPORTANT: The range and proper operation of any wireless device
will vary depending on its surroundings. It is very important that each
CO5-SS detector is tested with each receiver intended for alarm.
Detector Description
• LIsted to UL Standard 2034
• CO sensitivity is evaluated to UL 2034
• Local sounder
• Dual LED’s
• Test/Hush button
• Functional Gas Test
• Surface mount to wall or ceiling
• Optional drywall anchors included
The CO5-SS contains a piezoelectric horn which generates the ANSI
S3.41 temporal 4 pattern in an alarm condition (see note below Table
1 for temporal 4 pattern). In alarm, a message is also sent to a pro-
grammed Silent Call Receiver. The alarm message is transmitted every
4 seconds until the carbon monoxide condition has cleared and the de-
tector has reset. During an alarm condition, pressing the detector’s test
button will silence the piezoelectric horn for five minutes. The mounting
base installation is simplified by the incorporation of features compat-
ible with drywall fasteners or other methods that provide a method for
securing the detector in place.
Two LEDs and a sounder on the detector provide local visual and audi-
ble indication of the detector’s status as listed in Table 1.
During initial power-up, the red and green LEDs will blink together once
every 10 seconds four times. It takes about 30 seconds for the detector’s
CO sensor to stabilize (see Table 1).
After power-up has completed and the detector is functioning normally,
the green LED blinks once every 10 seconds. The LED indication must
not be used in place of the tests specified under
TESTING THE DETECTOR.
Table 1: Detector LED Modes
Chirp every 45 sec
beginning
7 days aer LED blinks,
connues 30 days
Sounder
Off
Temporal 4 Paern†
One Chirp every 45
seconds
Off
Off
Temporal 4 Paern†
Red LED
Off
Blinks every 1 second
Blinks every 45 seconds
for 37 days
Blinks every 5 seconds
Blinks every 10 seconds
Blinks every 10 secs ††
(w/green LED)
One Chirp every 45
seconds
Off
Blinks every 1 second
Green LED
Blinks every 10 seconds
Off
Off
Off
Off
Off
Blinks every 10 secs ††
(w/red LED)
Blinks every 1 second
Normal
(Standby)
Alarm/Test
Low Baery
Dectector Trouble
Dectector End-of-Life
Power Up
Funconal Gas Test
(Aer Co is Sprayed)
† Temp 4 pattern is repeated pattern of four short beeps followed by a five second pause.
If ambient conditions return to normal, the detector will self-restore out of alarm and into
the previous mode.
†† Red and green LEDs blink a total of four times, once every 10 seconds
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
