Silhouette SILHOUETTE DPAC120061 Bedienungsanleitung

OWNER’S MANUAL

MANUEL

D’UTILISATION

Model • Modèle >

DPAC120061

CAUTION:

Read and follow all safety

rules and operating

instructions before first use

of this product.

MISE EN GARDE :

Veuillez lire attentivement

les consignes de sécurité et

les directives d'utilisation

avant l'utilisation initiale de

ce produit.

ADVERTENCIA:

Es importante que lea y

observe todas las reglas de

seguridad e instrucciones de

operación antes de usar

esteproducto por primera

vez.

PORTABLE 3 SEASON HOME COMFORT

Table of contents . . . . . . . . . . . . . . . . . . . . . . 1

APPAREIL DE CONFORT AU FOYER

PORTABLE 3 SAISONS

Table des matières . . . . . . . . . . . . . . . . . . . . 21

Danby Products Ltd, PO Box 1778, Guelph, Ontario Canada N1H 6Z9

Danby Products Inc, PO Box 669, Findlay, Ohio USA 45839-0669

Version 1.12.07

Table Of Contents

Page

Introduction and Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Electrical and Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Energy-Saving Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Window Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Unit Parts Identification

Horizontal Louver

Blades

Removable

Air Filter Panel

(back)

Oscillating

Air Vents Carrying Handle

(both sides)

Easy-roll Castors

Remote Control

Receiver Window

Introduction

Thank you for choosing an Danby appliance to provide you and your family with all of the “Home Comfort”

requirements for your home, cottage or office. This Owner’s Manual will provide you with valuable

information necessary for the proper care and maintenance of your new appliance. If properly maintained,

your Danby appliance will give you many years of trouble free operation. Please take a few moments and

read the instructions thoroughly and familiarize yourself with all of the operational aspects of this appliance.

Your Danby Portable Air-Conditioner is a multi-functional room air-exchanging, air-processing appliance,

designed to offer you the functions of; Air Conditioning, Dehumidifying and Independent Fan. Each

individual mode, is featured with “oscillating” air swing capabilities. This unit can be conveniently moved from

room to room within your home and set-up in just minutes. Imagine the convenience of 3 Season Home

Comfort at your fingertips, anytime, anywhere. Just sit back and wait to feel what “Mother Nature” has

forecast and respond with the push of a button.

For easy reference, may we suggest you attach a copy of your sales slip/receipt to this page, along with the

following information which is located on the manufacturers nameplate located on the rear panel of the unit.

Model Number: DPAC120061

Serial Number: ___________________________________________________

Date of Purchase: _________________________________________________

Dealer’s Name and Address: ________________________________________

This information will be required if your unit requires servicing and/or for general inquiries. To contact a

Customer Service Representative, call Danby TOLL FREE.

1-800-26-DANBY

Unit Specifications: DPAC120061

Cooling Capacity 1200 Btu/h

Dehumidifying Capacity 70 Pints / 33.12L (24 Hrs)

Noise Level 52 dB (A)

Airflow CFM High / Medium / Low 450 / 380 / 300

Power Source 115 V / 60 Hz

Refrigerant R22

Internal Reservoir Capacity 1.9 L (4.0 Pints)

Unit Weight 48 kg (105.6 lb.)

Unit Dimensions (inches) W x D x H 17-1/2" x 20" x 33-11/16”

Unit Dimensions (cm) W x D x H 44.5 x 51.0 x 85.5

Fan Speeds 3

Control Panel (Illuminated) Soft Touch Controls

Remote Control Yes

Time of Day Clock Yes

Auto - Timer Yes

Power Consumption:

Cooling 1280 Watts (11.0 Amps)

Dehumidifying 1280 Watts (11.0 Amps)

Fan 90 W (0.8 Amps)

NOTE: Continuing research results in steady improvement. Therefore, this information and these

specifications are subject to change without notice.

Electrical Specifications

1. All wiring must comply with local and national

electrical codes and be installed by a qualified

electrician. If you have any questions regarding

the following instructions, contact a qualified

electrician.

2. Check available power supply and resolve any

wiring problems BEFORE installation and

operation of this unit.

3. This appliance draws 11 nameplate amps under

Cooling Mode and may be used in any properly

wired, general purpose 15 amp household

grounded receptacle.

4. For your safety and protection, this unit is

grounded through the power cord plug when

plugged into a matching wall outlet. If you are

not sure whether the wall outlets in your home

are properly grounded, please consult a qualified

electrician. DO NOT USE PLUG ADAPTERS

OR EXTENSION CORDS WITH THIS UNIT.

If it is necessary to use an extension cord with

this unit, use an approved “air conditioner”

extension cord only. (available at most local

hardware stores)

5. The manufacturers nameplate is located on the

rear panel of the unit and contains electrical and

other technical data specific to this unit.

6. To avoid the possibility of personal injury, always

disconnect the power supply to the unit, before

installing and/or servicing.

Power Supply Cord

The power cord supplied with this air conditioner

contains a device that senses damage to the power

cord. To test if your power cord is working properly,

you must do the following;

1 Connect the power supply cord to an electrical

outlet.

2. The power supply cord has two buttons located

on the head of the plug. One button is marked

‘TEST’, the other button is marked ‘RESET’.

Press the ‘TEST’ button, you will then hear a

click as the ‘RESET’ button pops out.

3. Press the ‘RESET’ button, you will hear a click

as the button engages.

4. The power supply cord is now energized and

supplying electricity to the air conditioner. (On

some products this is also indicated by a light on

the plug head).

Table 1

Suggested Individual Branch Circuit

Nameplate Amps AWG Wire Size*

11 14

AWG- American Wire Gage

* Based on copper wire at 60°C temperature rating.

Table 2

Receptacle and Fuse Types

Rated Volts 125

Amps 15

Wall Outlet

Fuse Size 15

Time Delay Fuse Plug Type

(or circuit breaker)

CAUTION

Do not leave this unit unattended in a space

where people or animals who cannot react to a

failed unit are located. A failed unit can cause

extreme overheating or death in such an

enclosed, unattended space.

The power cord supplied with this air conditioner

contains a current leakage detection device

designed to reduce the risk of fire. Please refer to

the section ‘Power Supply Cord’ for details. In the

event the power supply cord is damaged, it cannot

be repaired and must be replaced with a new cord

from the product manufacturer.

•Under no circumstances should this device be

be used to turn the unit on or off.

•The ‘RESET’ button must always be pushed in

(engaged) for correct operation.

•The power supply cord must be replaced if it fails

to reset when the ‘TEST’ button is pushed in.

Important Safety Instructions

Installation

Installation Accessories Fig. 1

LOCATION: Use this portable air conditioner on a

level surface only as inclinations greater than 3° can

cause water overflow.

Description Quantity

Flexible exhaust hose with collars & adapters...........2/set

stretches from 17-1/2" (44.5 cm) up to 55-1/2" (141 cm)

Adjustable window/patio door slider kit .....................4/set

from 28" (71.1 cm) up to 80" (203 cm)

Rain Hood (For slider kit) ..............................................1 kit

see pg #7 for assembly instructions

1.8m (70 14/16”) Drain Hose (Not Shown)......................1 pc

Air Intake Filter Basket (Not Shown).............................1 pc

SPECIAL NOTE: The exhaust/window kit must be

installed at all times when the unit is operating

under AIR CONDITIONING mode.

There should be at least 11.8" (30 cm) clearance

between the unit and any other objects or building

structure and should be installed on a level surface.

The unit does not have to be vented outside during

Dehumidifying/Fan mode operation, but it is

recommended that the hoses remain installed (on unit)

during Dehumidification.

CAUTION

To avoid installation/operation difficulties,

read these instructions thoroughly.

WARNING

When the patio door kit is installed, it will not be

possible to lock the patio door.

THIS COULD POSE A SECURITY RISK!

Installation of a “FOOTBOLT” or “DROP BAR”

behind the door is suggested. (Available through

most local hardware stores)

Electric Shock Hazard

To avoid the possibility of personal injury,

disconnect power to the unit before installing or

servicing.

Energy-Saving Tips

Your Danby appliance is designed to be highly

efficient in energy savings. Follow these

recommendations for greater efficiency.

1) Select a thermostat setting that suits your

comfort needs and leave at that chosen setting.

2) The air filter is very efficient in removing airborne

particles. Keep the air filter clean at all times.

3) Use drapes, curtains or shades to keep direct

sunlight from penetrating and heating room, but

do not allow drapes or curtains to obstruct the air

flow around the unit.

4) Start your air conditioner before the outdoor air

becomes hot and uncomfortable. This avoids an

initial period of discomfort while the unit is

cooling off the room. Use of the automatic

start/stop programmable TIMER feature can be

a major asset in this regard if utilized to the

fullest extent.

5) When outdoor temperatures are cool enough,

turn the air conditioner off and use the FAN

MODE on HIGH, MED or LOW. This circulates

indoor air, providing some cooling comfort and

utilizes less electricity.

Window Exhaust

Adapter (2)

Adjustable Window/Patio Door Slider Kit

28" - 80"

Flexible Exhaust Hose (2)

17-1/2" - 55-1/2"

Fig. 1 Installation Accessories

Rain Hood (1)

Rain Hood Inserts (2)

Hose Collar

Internal Safety Feature

This unit is equipped with a fail-safe switch

mechanism that prevents the unit from condensing

water in the event the internal reservoir becomes full.

If this situation occurs, the unit will signal (BEEP) for

20 seconds, and the (RED) WATER FULL indicator

light will flash.

NOTE:

During high humidity conditions, if the rate of water

being condensed exceeds the rate of water being

evaporated, the water level inside the internal

reservoir will activate a float switch mechanism

(safety shut-off), causing the unit to stop/cease

operation automatically. In this event,

•the red “water full” indicator light on the control

panel will begin to flash

•and a warning beep will sound.

To return to normal operation:

1. Switch the unit off;

2. Place a pan with a 1.9L (4 pts) capacity

beneath the lowest drain ports located on the

bottom rear of the unit (see Fig. D1).;

3. Open the drains by unscrewing their drain caps;

4. Wait until all the water inside the internal reservoir

is emptied, then reattach the drain caps;

5. Properly dispose of the water in the pan;

6. Switch the unit on.

It may take 3-5 minutes for the compressor to

re-start. This is normal.

Direct Drain Instructions

Direct drain operation is intended for floor drain

application only. Direct drain cannot be used in stem

pipe and / or sink applications:

While the unit is off:

1. Locate the unit as close as you can to the floor

drain you will be using for water drainage;

2. Remove the drain cap located in the middle

(approximately) of the back of the unit (see Fig.

D2);

3. Attach the hose’s coupler directly onto the direct

drain’s thread and hand-tighten to seal the

connection;

4. Place the open end of the drain hose directly over

the floor drain.

You may now start the unit and begin dehumidifying.

NOTE: Remember to remove the hose and re-install

the drain cap when the direct drain feature is not in

use.

Fig. D1

Fig. D2

Remove

Window / Patio Door Kit Installation

(Air Conditioning Mode ONLY)

Your window kit has been designed to fit most

standard “vertical” / “horizontal” windows and patio

doors up to a maximum height of 80”. For vertical

window and/or patio door applications, lock

positions are provided in each slider sction. Wing

nuts are also provided to secure the sections

togethor (see Fig. 5a).

Rain Hood Assembly

1) Fold both sides of

the Rain Hood 90

as so

the flanges are facing

outward. Fig 1

2) Slide the Rain Hood

flanges onto the edges of

the slider kit until it is

lined up with the intake

vent (shown in Fig 2). Once the mounting holes on

the slider, as well as the Rain Hood are aligned,

secure the Rain Hood to the slider with the four

mounting screws provided.

IMPORTANT:

• For horizontal window kit applications refer to

figure 3a for correct Rain Hood insert positioning.

• For vertical window kit applications (including

patio) refer to figure 4a for correct Rain Hood insert

positioning.

1) Select a suitable location,making sure you have

access to an electrical outlet.

2) Install both flexible hoses to the rear side of the

unit. Both hoses are identical and can be installed

into either opening. Insert the hose collar with the 2

lock tabs into the 2 slots on the top of each

opening and twist to lock into position.

3) Install the adjustable Window/Patio Door Slider

Kit as required. Fig’s. 3, 4, 5.

4) Install the window exhaust adapters into the

openings in the slider section, making sure the

window slider sections are secure.

Important:: Ensure the exhaust adapter labeled “air

intake” is installed on the hose that is connected to

the air intake opening on the back of the unit.

Horizontal Window

Window Slider Kit

Minimum: 28" (71.1 cm)

Maximum: 48 3/8" (123 cm)

Vertical

Window

Fig. 3

Fig.4

Patio

Door

Patio Door Kit

Minimum: 28" (71.1 cm)

Maximum: 80" (203 cm)

Fig. 5

Fig.

Please Note: In a vertical application, the

exhaust hose MUST be positioned above the

intake hose in the window slider. See Fig 5.

This will avoid having the exhaust heat go

through the intake and back into the unit.

Window Slider Kit

Minimum: 28" (71.1 cm)

Maximum: 48 3/8" (123 cm)

Fig. 3a

Fig. 2

Fig. 1

Rain hood inserts are

installed in “A” and “B”

postions with vent open-

ing facing down (C)

Fig.4a

Intake hose

adapter

Rain

Hood

Slider kit

Rain hood inserts are

installed in “A” and “C”

positions with vent open-

ing facing down (B)

Rain Hood is to be installed only over air intake vent

Air exhaust

Air intake

Plug the unit into a 115 V / 60 Hz grounded

electrical outlet.

I/O Power Switch: Turns unit On / Off.

MODE : Allows you to scroll through and select

desired operating mode.

FAN : Select from three different fan speeds;

Low, Medium and High, during Cool and Fan

mode. Please note: During ‘Dry’ mode there is

only one fan speed utilized (low) .

SWING : Allows the vertical louver grills to

oscillate from side to side automatically.

TEMPERATURE /TIMER Adjust :

+:Used to adjust Clock and Timer On/Off settings

forward (1 min./1hr. increments).

Used to adjust Temperature settings forward

(1°C / °F increments).

- : Used to adjust Clock and Timer On/Off settings

backward (1 min./1hr. increments).

Used to adjust Temperature settings backward

(1°C / °F increments).

TIMER ON : Used to initiate the AUTO ON

start time.

TIMER OFF: Used to initiate the AUTO OFF

stop time.

CLOCK : Allows you to initiate and/or change

the “TIME OF DAY” setting. To activate clock

mode both the TIMER ON and TIMER OFF

buttons must be pressed simultaneously.

Note: This appliance allows you select the

temperature scale displayed in either “Celsius” or

“Fahrenheit” according to your preference.

To change temperature scale displayed on the control

panel display, press both of the “Temp/Timer” adjust

arrows simultaneously to alternate between “Celsius”

& “Fahrenheit”.

Key Pad Functions Indicator Lights & Display Icons

RUN: Adjacent blue indicator light

illuminates to indicate selected mode is

operational.

WATER FULL :

A warning signal

(beep) will sound and the

adjacent red

indicator light will flash continously

indicating the internal reservoir is full.

See “Internal Safety Feature” on pg.5 for

additional details.

ICONS

MODE FAN /SPEED

Cool

Dry (Dehumid.)

Fan Only

TIME / TIMER

Clock: Illuminates when the time (hour) is

being modified.

Timer On: Illuminates when the auto-on

time (hour) is being defined.

Timer Off: Illuminates when the auto-off

time (hour) is being defined.

High

Medium

Low

Swing

Setting TIME OF DAY (Clock):

NOTE: This is a 24:00 hour clock system

Push and hold the CLOCK (TIMER ON / TIMER OFF) key

pads simultaneously Fig A. The clock symbol appears in the

display and the minute “00” digits start flashing Fig C. Press

the TEMP/TIMER buttons Fig B until the correct time (in

minutes) is displayed. Press either of the clock (TIMER ON /

TIMER OFF) buttons. The hour “0” digit starts flashing. Press

the TEMP/TIMER buttons until the correct time (hour) is

displayed. When the correct time appears in the display, press

the CLOCK (TIMER ON / TIMER OFF) key pads

simultaneously. The colons (:) between the hour and

minutes start flashing, indicating the time of day is now set.

Important Note: Any interruption to the electrical

power supply will automatically cancel the TIME

OF DAY clock program. In the event this should

happen, you will be required to re-set the

clock program.

Operating Instructions (Air Conditioning):

NOTE: Both exhaust hoses must be installed and

properly vented (outdoors) during air conditioning

mode.

1) Press the I/O (on/off) key pad to switch on the

unit. Fig D.

2) Press the MODE key until the COOL symbol

appears in the display window Fig E. Each

.....depression of the MODE key will advance to a

.....different mode setting (Auto-Cool-Dry-Fan).

3) Press the appropriate (TEMP / TIMER/ADJ) keys

to select a suitable operating temperature setting

Fig B. Temperature settings are adjustable

between 16°C (61°F) to 31°C (88°F ). The set

temperature will flash in the display window for

approximately 5 seconds then automatically

revert back to display actual room ambient

temperature conditions. NOTE: The set operating

temperature must be programmed within the 5

second (temperature flashing) condition. To view

the “set” temperature any time, press either of

the TEMP/TIMER ADJ buttons. The blue

indicator light will activate indicating the air

conditioning mode is operational (there may be a

slight delay of 10-30 seconds before the cycle

begins, this is normal).

Fig E

Fig B

Fig A

Fig C

Fig D

Air Conditioner Operating Instructions

(cont’d)

4) Press the FAN key Fig F (1) to select the desired

fan speed setting (Auto-Low-Med-High). Your

selection will appear in the display window

(each depression of the fan key will advance

to a different setting).

5) Press the SWING key Fig F (2) to activate the

automatic air swing (oscillating) feature and the

swing symbol will appear in the display window

(Fig G). To deactivate the air swing feature, press

the SWING key again.

6) The horizontal louvers open and close

automatically when the unit is switched on

and off. To adjust “air flow” direction, (up / down

only) adjust the center louver only up or down

Fig 16.

The blue indicator light will come on indicating the

air-conditioning mode is operational (there may be a

slight delay of 10-30 seconds before the cycle

begins, this is normal).

Cooling stops automatically when the set temperature

is achieved. Cooling resumes when the room

temperature rises above the set temperature level.

The temperature has no effect on the fan operation.

Therefore, the fan will operate continuously (after the

compressor has cycled off) to maintain optimal

temperature control.

Fig. 16

During air

During air conditioning and dehumidifying

modes, if the compressor cycle is interupted

(unplugged, power failure,etc.) and reinstated

immediately thereafter, (within 3-5 minutes) a

“compressor protection circuit” is automatically

activated. The compressor cannot operate

during a “compressor protecton” condition (this

is normal), and it may take 3-5 minutes before

the “protection circuit” deactivates.

DO NOT ATTEMPT TO START THE UNIT

(COMPRESSOR) DURING THIS PERIOD.

Upon reinstating power to the unit all previous

settings (i.e. time, mode, fan speed, auto

timed programs) are lost and will have to be

re-entered.

Fig F

C A U T I O N

Inhaltsverzeichnis

Sprachen:

Andere Silhouette Klimaanlage Handbücher

Silhouette

Silhouette DCAP 12030 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung