Silicon Laboratories Si5348-E Bedienungsanleitung

UG362: Si5348-E Evaluation Board User's

Guide

The Si5348-E-EVB is used for evaluating the Si5348 Network Synchronizer Clock for

SyncE/1588 and Stratum 3/3E applications. The device revision is distinguished by a

white 1 inch x 0.187 inch label with the text “SI5348-E-EB” in the lower left-hand corner

of the board. (For ordering purposes only, the terms “EB” and “EVB” refer to the board

and the kit respectively. In this document, the terms are synonymous in context.) The

Si5348 contains three independent DSPLLs in a single IC with programmable jitter at-

tenuation bandwidth on a per DSPLL basis. The Si5348-E-EVB supports three inde-

pendent differential input clocks, two independent CMOS input clocks, and seven inde-

pendent output clocks via onboard SMA connectors. The Si5348-E-EVB can be con-

trolled and configured via a USB connection to a host PC running Silicon Labs’ next

generation Clock Builder Pro™ (CBPro™) software tool. Test points are provided on-

board for external monitoring of supply voltages.

The device revision is distinguished by a white 1 inch x 0.187 inch label with the text

“SI5348-E-EB” installed in the lower left hand corner of the board. (For ordering purpo-

ses only, the terms “EB” and “EVB” refer to the board and the kit respectively. For the

purpose of this document, the terms are synonymous in context.

This kit comes with an OCXO board SiOCXO1-EB as well as a TCXO board SiTCXO1-

EB. The OCXO or the TCXO are used on the reference input (REF) of the Si5348 to

evaluate the holdover stability of the network synchronizer clock. Both boards are not

needed at the same time, but they are both included in the kit to provide a comparison

of the resulting performance.

EVB FEATURES

• Powered from USB port or external +5 V

power supply via screw terminals

• Included SiOCXO1-EB reference OCXO

board allows for evaluation in standalone

and holdover mode.

• Included SiTCXO1-EB reference TCXO

board allows for evaluation in standalone

and holdover mode.

•CBPro™ GUI programmable VDD supply

allows device supply voltages from 3.3,

2.5, or 1.8 V

• CBPro™ GUI programmable VDDO

supplies allow each of the seven outputs

to have its own supply voltage selectable

from 3.3, 2.5, or 1.8 V

• CBPro™ GUI allows control and

measurement of voltage, current, and

power of VDD and all 8 VDDO supplies

• Status LEDs for power supplies and

control/status signals of Si5348

• SMA connectors for input clocks, output

clocks and optional external timing

reference clock

silabs.com | Building a more connected world. Rev. 0.1

Figure .1. Si5348-E-EVB

Figure .2. SiOCXO1-EB (left) SiTCXO1-EB (right)

silabs.com | Building a more connected world. Rev. 0.1

1. Si5348-E-EVB Functional Block Diagram, Support Documentation, and ClockBuilderPro™ Software

Below is a functional block diagram of the Si5348-E-EVB. This EVB can be connected to a PC via the main USB connector for pro-

gramming, control, and monitoring. See 2. Quick Start and Jumper Defaults for more information.

Si5348

CLKOUT_0

CLKOUT_0B

Output

Termination

CLKOUT_1

CLKOUT_1B

Output

Termination

CLKOUT_2

CLKOUT_2B

Output

Termination

CLKOUT_3

CLKOUT_3B

Output

Termination

CLKOUT_4

CLKOUT_4B

Output

Termination

CLKOUT_5

CLKOUT_5B

Output

Termination

Input

Termination

Input

Termination

Input

Termination

REF_IN

REF_INB

CLKIN_0

CLKIN_0B

CLKIN_1

CLKIN_1B

Power Supply

C8051F380

MCU

Peripherals

I2C/SPI Bus

VDDO_0

VDD_Core

VDD_3.3

VDDO_1

VDDO_2

VDDO_3

VDDO_4

VDDO_5

VDDO_0

VDD_Core

VDD_3.3

VDDO_1

VDDO_2

VDDO_3

VDDO_4

VDDO_5

USB +5V

Connector

USB Aux +5V

Connector

Ext +5V

Connector

I2C

+5V

+5V_Aux

VDDMCU

5–250 MHz TCXO/OCXO

or REFCLK {

Input Clock 0 {

Input Clock 1 {

}Output Clock 0

}Output Clock 1

}Output Clock 2

}Output Clock 3

}Output Clock 4

}Output Clock 5

Power only

Control/

Status

INTR

Alarm_Status

Input

Termination

CLKIN_2

CLKIN_2B

{

VDDO_6 VDDO_6

CLKOUT_6

CLKOUT_6B

Output

Termination }Output Clock 6

Ext Aux +5V

Connector

SPI

Conn

Optional External

XAXB Ref Input {XAXB

Crystal/Term

Input Clock 3

Input Clock 4

CLKIN_3

CLKIN_4

Input Clock 2

Figure 1.1. Si5348-E-EVB Functional Block Diagram

All Si5348 schematics, BOMs, User’s Guides, and software can be found online at the following link: http:www.silabs.com/products/

clocksoscillators/pages/si538x-4x-evb.aspx

The SiOCXO1-EB User's Guide is located at: https://www.silabs.com/documents/public/user-guides/UG123.pdf

The SiTCXO1-EB User's Guide is located at: https://www.silabs.com/documents/public/user-guides/ug364-sitcxo1-evb-ug.pdf

UG362: Si5348-E Evaluation Board User's Guide

Si5348-E-EVB Functional Block Diagram, Support Documentation, and ClockBuilderPro™ Software

silabs.com | Building a more connected world. Rev. 0.1 | 3

2. Quick Start and Jumper Defaults

1. Install ClockBuilderPro desktop software from EVB support web page given in Section 2.

2. Connect USB cable from Si5348-E-EVB to PC with ClockBuilderPro software installed.

3. Connect the SIOCXO1-EB or SiTCXO1-EB to the reference input (REF) on the Si5348 using the included SMA connector.

4. Leave the jumpers as installed from the factory, and launch the ClockBuilderPro software.

5. You can use ClockBuilderPro to create, download, and run a frequency plan on the Si5348-E-EVB.

6. For the Si5348 data sheet, go to https://www.silabs.com/documents/public/data-sheets/si5348-e-datasheet.pdf.

7. For the Si5348 reference manual, go to http://www.silabs.com/documents/public/reference-manuals/si5348-e-family.pdf.

Table 2.1. Si5348-E EVB Jumper Defaults*

Location Type I = Installed O =

Open

Location Type I = Installed O =

Open

JP1 2 pin I JP23 2 pin O

JP2 2 pin I JP24 2 pin O

JP3 2 pin I JP25 2 pin O

JP4 2 pin I JP26 2 pin O

JP5 2 pin O JP27 2 pin O

JP6 2 pin O JP28 2 pin O

JP7 2 pin I JP29 2 pin O

JP8 2 pin O JP30 2 pin O

JP9 2 pin O JP31 2 pin O

JP10 2 pin I JP32 2 pin O

JP13 2 pin O JP33 2 pin O

JP14 2 pin I JP34 2 pin O

JP15 3 pin 1 to 2 JP35 2 pin O

JP16 3 pin 1 to 2 JP36 2 pin O

JP17 2 pin O JP38 3 pin All open

JP18 2 pin O JP39 2 pin O

JP19 2 pin O JP40 2 pin O

JP20 2 pin O JP41 2 pin O

JP21 2 pin O

JP22 2 pin O J36 5x2 Hdr All 5 installed

Note: Refer to the Si5348-E-EVB schematics for the functionality associated with each jumper.

UG362: Si5348-E Evaluation Board User's Guide

Quick Start and Jumper Defaults

silabs.com | Building a more connected world. Rev. 0.1 | 4

3. Status LEDs

Table 3.1. Si5348-E EVB Status LEDs

Location Silkscreen Color Status Function Indication

D27 5VUSBMAIN Blue Main USB +5 V present

D22 3P3V Blue DUT +3.3 V is present

D26 VDD DUT Blue DUT VDD Core voltage present

D25 INTR Red MCU INTR (Interrupt) active

D21 READY Green MCU Ready

D24 BUSY Green MCU Busy

D5 LOL_T0B Blue Loss of Lock - DSPLL C

D6 LOL_T4B Blue Loss of Lock - DSPLL D

D8 LOS2B Blue Loss of Signal at IN2

D11 INTRB Blue Si5348 Interrupt Active

D12 LOS1B Blue Loss of Signal at IN1

D13 LOL_AB Blue Loss of Lock DSPLL A

D14 LOS0B Blue Loss of Signal at IN0

D27, D22, and D26 are illuminated when USB +5 V, Si5348-E-EVB +3.3 V, and Si5348 VDD or supply voltages, respectively, are

present. D25, D21, and D24 are status LEDs showing on-board MCU activity. LEDs D14, D12, and D8 indicate loss of signal at clock

inputs IN0, IN1, and IN2, respectively. LEDs D13, D5, and D6 indicate loss of lock for one of three internal DSPLLs (A, C, and D) re-

spectively. D11 indicates Si5348 interrupt output is active (as configured by Si5348 register programming). LED locations are highligh-

ted below with LED function name indicated on board silkscreen.

Figure 3.1. Si5348-E-EVB LED Locations

UG362: Si5348-E Evaluation Board User's Guide

Status LEDs

silabs.com | Building a more connected world. Rev. 0.1 | 5

4. External Reference Input (XA/XB)

An external timing reference (48 MHz XTAL) is used in combination with the internal oscillator to produce an ultra-low jitter reference

clock for the DSPLL and for providing a stable reference for the free-run and holdover modes. The Si5348-E-EVB can also accommo-

date an external reference clock instead of a crystal. To evaluate the device with an external REFCLK, C111 and C113 must be popula-

ted and XTAL Y1 removed (see figure below). The REFCLK can then be applied to SMA connectors J39 and J40.

Figure 4.1. External Reference Input Circuit

UG362: Si5348-E Evaluation Board User's Guide

External Reference Input (XA/XB)

silabs.com | Building a more connected world. Rev. 0.1 | 6

5. Clock Input and Output Circuits

5.1 Clock Input Circuits (REF/REFB, IN0/IN0B-IN2/IN2B, IN3, IN4)

The Si5348-E-EVB has eight SMA connectors (REF/REFB, IN0/IN0B–IN2/IN2B) for receiving external differential clock signals. The

REF/REFB differential input clock is intended to support a TCXO or OCXO, such as the included SiOCXO1-EB or the included SiTC-

XO1-EB, which determines the Si5348’s wander performance. (Please note that this input clock is different from the optional reference

clock that may be applied at XA/XB.) All differential input clocks are terminated as shown in the figure below. The only exception is that

the terminating 49.9 Ω resistor for REF is not installed. This is R84 corresponding to IN0's R76 in the figure below. The reason for this

exception is that single-ended TCXOs and OCXOs typically cannot drive a 50 Ω load. Note that input clocks are ac-coupled and 50 Ω

terminated. This represents four differential input clock pairs. Single-ended clocks can be used by appropriately driving one side of the

differential pair with a single-ended clock. For details on how to configure inputs as single-ended, please refer to the Si5348 data sheet

or reference manual.

Figure 5.1. Differential Input Clock Termination Circuit

In addition, the Si5348-E-EVB supports two SMA connectors (IN3, IN4) for receiving external single-ended LVCMOS clocks. Each of

these clocks connects to its respective Si5348 pins via a single installed 0 Ω resistor. There are no other termination components on

the EVB.

UG362: Si5348-E Evaluation Board User's Guide

Clock Input and Output Circuits

silabs.com | Building a more connected world. Rev. 0.1 | 7

5.2 Clock Output Circuits (OUTx/OUTxB)

Each of the 14 output drivers (seven differential pairs, OUT0/OUT0B—OUT6/OUT6B) is ac-coupled to its respective SMA connector.

The output clock termination circuit is shown in the figure below. The output signal will have no dc bias. If dc coupling is required, the ac

coupling capacitors can be replaced with a resistor of appropriate value. In particular, if differential pair OUT6/OUT6B is configured for 1

Hz output, then the AC coupling output capacitors, C166 and C168, each need to be replaced by a 0 Ω resistor. (These capacitors are

the respective counterparts of the OUT0/OUT0B output capacitors, C25 and C27, in the figure below.) The Si5348-E-EVB provides

pads for optional output termination resistors and/or low-frequency capacitors. Note that components with schematic “NI” designation

are not normally populated on the Si5348-E-EVB and provide locations on the PCB for optional dc/ac terminations by the end user.

Figure 5.2. Output Clock Termination Circuit

UG362: Si5348-E Evaluation Board User's Guide

Clock Input and Output Circuits

silabs.com | Building a more connected world. Rev. 0.1 | 8

6. Using the Si5348-E-EVB and Installing ClockBuilderPro (CBPro) Desktop Software

6.1 Installing ClockBuilderPro (CBPro) Desktop Software

To install the CBPro software on any Windows 7 (or above) PC:

Go to http://www.silabs.com/CBPro and download ClockBuilderPro software.

Installation instructions and User’s Guide for ClockBuilder can be found at the download link shown above. Please follow the instruc-

tions as indicated.

6.2 Connecting the EVB to Your Host PC

Once ClockBuilderPro software is installed, connect to the EVB with a USB cable as shown below.

Figure 6.1. EVB Connection Diagram

6.3 Additional Power Supplies

The Si5348-EB comes pre-configured with jumpers installed at JP15 and JP16 (pins 1–2 in both cases) in order to select “USB”. These

jumpers, together with the components installed, configure the evaluation board to obtain all +5 V power solely through the main USB

connector at J37. This setup is the default configuration and should normally be sufficient.

The general guidelines for single USB power supply operation are listed below:

• Use either a USB 3.0 or USB 2.0 port. These ports are specified to supply 900 mA and 500 mA respectively at +5 V.

• If you are working with a USB 2.0 port and you are current limited, turn off enough DUT output voltage regulators to drop the total

DUT current ≤ 470 mA. (Note: USB 2.0 ports may supply > 500 mA. Provided the nominal +5 V drops gracefully by less than 10%,

the EVB will still work.)

• If you are working with a USB 2.0 and you are current limited and need all output clock drivers enabled, re-configure the EVB to

drive the DUT output voltage regulators from an external +5 V power supply as follows:

• Connect external +5 V power supply to terminal block J33 on the back side of the PCB.

• Move the jumper at JP15 from pins 1–2 USB to pins 2–3 EXT.

UG362: Si5348-E Evaluation Board User's Guide

Using the Si5348-E-EVB and Installing ClockBuilderPro (CBPro) Desktop Software

silabs.com | Building a more connected world. Rev. 0.1 | 9

6.4 Overview of ClockBuilderPro Applications

Note: The following instructions and screen captures may vary slightly depending on your version of ClockBuilder Pro.

The ClockBuilderPro installer will install two main applications:

Figure 6.2. Application #1: ClockbuilderPro Wizard

Use the CBPro Wizard to:

• Create a new design

• Review or edit an existing design

• Export: create in-system programming files

Figure 6.3. Application #2: EVB GUI

UG362: Si5348-E Evaluation Board User's Guide

Using the Si5348-E-EVB and Installing ClockBuilderPro (CBPro) Desktop Software

silabs.com | Building a more connected world. Rev. 0.1 | 10

Inhaltsverzeichnis

Andere Silicon Laboratories Hauptplatine Handbücher

Silicon Laboratories

Silicon Laboratories EFR32MG13 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F850 BLDC Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5397 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFR32MG12 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5365-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFR32MG13 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si3454-KIT Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories TS3310DB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories CP2104 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Biometric-EXP EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories BRD4175A Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFR32ZG14 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si890x-PWR-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si3474-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5381/82 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5328-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si82 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5-EVB Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si80xx-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5041-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Si5350/51-B20QFN-EVB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories M88 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F04 DK Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories SI2493/57/34/15/04 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung