Silver Cross Sleepover Bedienungsanleitung
SLEEPOVER
IMPORTANT: KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
2
These instructions are important.
Please read these instructions carefully
before you use this pushchair and keep
them for future reference. Also ensure
that anyone else unfamiliar with this
pushchair reads the instructions carefully
so they understand how the product
works. This Sleepover 3-in-1 pushchair is
a high quality Silver Cross product that
meets current safety standards; regular
care and light maintenance will ensure its
long service. This pushchair is intended to
accommodate children from birth to 15kg
in weight. Remember, the safety of your
child is your responsibility.
WARNING: NEVER LEAVE YOUR
CHILD UNATTENDED.
Contents
Your Sleepover 3-in-1 includes the following
components, please check that you have
all the items before proceeding:
1.1 Carrycot body
1.2 Seat Unit (including harness)
1.3 Hood
1.4 Apron
1.5 Carrycot Liner
1.6 Carrycot Mattress
1.7 Footmu
1.8 Bumper Bar
1.9 Rosette
1.10 Bag
1.11 Raincover
1.1
1.2
1.3
1.4
1.5
1.6 1.7
1.9
1.10 1.11
1.8
3
Using your Sleepover from Birth
with the Carrycot.
2.1 First erect the carrycot body.
Lay the carrycot outer down with
frame upper most. Using the 2
webbing loops that are attached to
the metal bars, pull the top metal
bars into the locators on the internal
base of the carrycot.
A small groove in the locator holds
the frame in place.
2.2 Attach the carrycot liner to the
carrycot outer using the elasticated
top edge. Ensure the holes on the top
are located over the hood attachment
points.
Place the mattress into the base of
the carrycot.
2.3 Attach your hood to the carrycot by
inserting the clips into the slots on
the top edge of the carrycot. Fasten
the press studs on the hood to the
press studs on the carrycot - two at
the back and one at each side.
2.4 Fit the carrycot apron by tting it
around the carrycot and slide the
apron clips over the attachment
points, located on the inside of the
hood frame.
2.1
2.3
2.2
2.4
4
Attaching the Carrycot to your
chassis.
3.1 Before attaching the carrycot to the
chassis, lower the hood to the lowest
position.
3.2 There are two zip pockets on either
sides of the carrycot body. Remove
the handles from the pockets.
3.3 Lift the carrycot using the two handles
in one hand and position the carrycot
so the four locking catches on the
base are directly over the top of the
support bars on your chassis.
Using the other hand, press
downwards on each side of the
carrycot, listening for the two clicks.
Pull upwards with the handles to
ensure the carrycot is locked in place.
3.4 When the carrycot is attached, zip the
handles back into the side pockets.
The hood can now be raised.
WARNING: WHEN
ATTACHING, DETACHING
AND HAND CARRYING THE
SLEEPOVER CARRYCOT,
THE HOOD MUST BE IN THE
LOWEST POSITION.
WARNING: DO NOT LEAVE
FLEXIBLE CARRYING
HANDLES INSIDE THE
CARRYCOT.
3.1
3.2
3.3
3.4
‘CLICK’
‘CLICK’
5
Detaching the Carrycot from
your chassis.
4.1 Before detaching the carrycot from
the chassis, lower the hood to the
lowest position.
4.2 Remove the handles from the side
pockets of the carrycot.
When standing behind the chassis
handle, slide the RIGHT HAND SIDE
release lever away from you until it
clicks into place.
4.1
4.2
WARNING: THIS BUTTON
IS NOW UNLOCKED.
IT WILL RELOCK
AUTOMATICALLY ONLY
WHEN THE CARRYCOT IS
REMOVED AND
REATTACHED TO THE
CHASSIS.
Then while holding both handles
securely in one hand, slide the
LEFT HAND SIDE release
lever away from you and hold
whilst lifting.
6
4.3
WARNING: THE HANDLES
MUST BE STORED IN THE
ZIP POCKETS EXCEPT WHEN
ATTACHING OR DETACHING
THE CARRYCOT
WARNING: WHEN USING
THE CARRYCOT WITHOUT
THE CHASSIS. ONLYUSE ON
AFIRM, HORIZONTAL LEVEL
AND DRYSURFACE.
WARNING: BOTH
HANDLES MUST BE HELD
SECURELYTOGETHER
WHEN ATTACHING AND
DETACHING THE SLEEPOVER
CARRYCOT FROM THE
CHASSIS. YOU MUST NOT
LET GO OF THE HANDLES
UNTIL THE CARRYCOT IS
EITHER SECURELY FASTENED
TO THE CHASSIS OR SAT
ON AFIRM, LEVEL AND DRY
SURFACE.
4.3 Lift the carrycot upwards from the
chassis using the handles. The
LEFT HAND SIDE release lever
can be released when the carrycot
is clear of the chassis.
7
Operating the Hood on the
Carrycot.
5.1 The Sleepover hood is multi
positional. Simply hold the front bar
and gently lift and lower.
5.2 To remove the hood, rstly, undo the
4 press studs from the Sleepover hood
- two at the back and one at each
side. Locate the hood release buttons
at the each side of the carrycot, just
underneath each hood attachment
point. Press the button to release the
clip and lift the hood upwards. Failure
to press the release button may result
in damage to your product.
5.3 Your Sleepover hood has a ventilation
panel underneath the rear panel and
a pop-out sun visor.
To use the ventilation panel, simply
lift up the panel at the back of the
hood to expose the ventilation mesh.
The pop-out sun visor can be pulled
out from underneath the hood and
pushed back when not needed.
5.1
5.2
5.3
8
Carrycot Ventilation
6.1 Your Sleepover carrycot body has
ventilation holes in the base.
There is a lever on the underside of
the carrycot at the hood end.
The ventilation can be opened and
closed by moving the lever left or
right.
Carrycot rocking feature
7.1 The Sleepover carrycot base has a
gentle rocking feature.
7.2 The rocking feature is prevented or
allowed by lowering or raising the
four feet on the carrycot base.
6.1
7.1
7.2
9
8.1 Using your Sleepover from 6
Months as a Pushchair.
Attaching the seat unit to the
chassis.
8.1 The Sleepover seat unit can be used in
forward facing and rearward facing
mode.
8.2 Position the seat unit so the four
locking catches on the base are
directly over the top of the support
bars on your chassis. Push the seat
unit downwards so that all four locks
‘click’ and engage. Give the seat unit
a gentle lift to check that all four
points are securely fastened.
WARNING: ALWAYS PICK
YOUR SLEEPOVER SEAT
UNIT UP BY THE HANDLES
SITUATED BELOW THE SIDE
ARMS, NEVER BY THE HOOD
OR BUMPER BAR.
10
Detaching the seat unit from the
chassis.
9.1 Place your hands in the elasticated
side pockets of the Sleepover seat
unit.
9.2 Gently grip the inner release catch,
and slide the release handle towards
the foot end of the Sleepover seat
unit. Squeeze to release the locking
catches. The seat unit will now lift
clear of the chassis.
9.2
Andere Handbücher für Sleepover
1
Inhaltsverzeichnis
Andere Silver Cross Kinderwagen Handbücher
Silver Cross
Silver Cross POP Bedienungsanleitung
Silver Cross
Silver Cross Sleepover Deluxe - Words Bedienungsanleitung
Silver Cross
Silver Cross POP Bedienungsanleitung
Silver Cross
Silver Cross Wave Bedienungsanleitung
Silver Cross
Silver Cross Avia Bedienungsanleitung
Silver Cross
Silver Cross ZEST Bedienungsanleitung
Silver Cross
Silver Cross Comet Bedienungsanleitung
Silver Cross
Silver Cross Freeway Bedienungsanleitung
Silver Cross
Silver Cross Coast Bedienungsanleitung
Silver Cross
Silver Cross Wayfarer Bedienungsanleitung
Silver Cross
Silver Cross Fizz Bedienungsanleitung
Silver Cross
Silver Cross Sleepover Elegance Bedienungsanleitung
Silver Cross
Silver Cross Coast Bedienungsanleitung
Silver Cross
Silver Cross SURF Bedienungsanleitung
Silver Cross
Silver Cross Pacific Bedienungsanleitung
Silver Cross
Silver Cross 3D Pram System Bedienungsanleitung
Silver Cross
Silver Cross Wayfarer Bedienungsanleitung
Silver Cross
Silver Cross Wave Bedienungsanleitung
Silver Cross
Silver Cross Doll’s Pram Bedienungsanleitung
Silver Cross
Silver Cross Tide Bedienungsanleitung
