SilverSaver 1000 Bedienungsanleitung
Smart Flatware Detector
SilverSaver®1000
User Manual
You have purchased the most effective restaurant utensil recovery system in
the industry. Please read this operation manual before you start to use your
SilverSaver®1000. It will help you understand its operation, maintenance, and
cleaning procedures to ensure maximum savings and years of reliable use.
Contents
3SilverSaver®1000 Parts
4Control Box
5Assembly
7Powering Up the SilverSaver®1000
8Operation
9False Alarms
10 Tips for Best Results
11 Ramekins
12 Cleaning
14 Batteries and Charging
16 Troubleshooting
18 TechnicalSpecications
19 Reference Card
SilverSaver®1000 User Manual3
SilverSaver®1000 Parts
Snap Clip Cradle
Magnetic
Connector and
Connector Pads
Trash Can
(not included)
Body
Handle
Axle Slots
Tray
Tray
Axle
Control
Box
1
2
3
5
7
8
10
11
64
9
SilverSaver®1000 User Manual4
Control Box
1 Battery Charging Port
2 Battery Charge Status Light (blue)
Flashing Charging
Solid on Charging complete
3 Power On/Off Button
4 Power On/Low Battery Light (green)
Flashing Low Battery
Solid on Power On
5 Reset Button
6 Detection Mode Light (blue)
Off Full Detection Mode
Solid on Reduced Detection
Mode (RDM)
7 Volume Up Button
8 Volume Down Button
9 Volume Level Lights (green)
All off Levels 0 and 1
1 Solid on Levels 2, 3 and 4
2 Solid on Levels 5, 6 and 7
10 Error Light (yellow)
Flashing Tray is open
Solid on Magnetic Connector
disconnected
11 Detection Light (red)
Flashing Metal object detected
SilverSaver®1000 User Manual5
1. Place the SilverSaver®1000 Body on top of a
32 or 44-gallon round trash can.
CAUTION: Use of other trash cans may result in
instability and injury!
2. Insert the Control Box into the Cradle on the
Body by first sliding the right end under the
right-side clip.
Then lower the left side of the Control Box until
the Snap Clip on the left clicks into place.
CAUTION: Do not bend the Snap Clip back
further than necessary as this could break it.
Assembly
SilverSaver®1000 User Manual6
3. Place the Tray in the Body, setting the two Tray
Axles into the Axle Slots of the Body.
4. Rotate the Tray downward, black side down
until a click is heard as the Handle locks
into place.
CLICK
5. Connect the Tray to the Control Box by
snapping the Magnetic Connector onto the
Connector Pads on the Tray Axle.
Test for a solid connection by pressing lightly
down on the cable near the Magnetic
Connector to ensure that the Magnetic
Connector remains connected.
Assembly (continued)
SilverSaver®1000 User Manual7
1. Position the trash can so that it is not touching or underneath any metal counters or walls.
2. Ensure Tray is latched, with no metal objects on the Tray.
3. Press and the Volume Level Lights (green) will begin to flash. The Power On Light (green) will
illuminate solid within 2 seconds.
4. Set the volume of the speaker by placing a metal object, such as a fork, on the Tray to activate
the alarm. Adjust the volume by pressing or buttons until the volume is at the desired level.
Remove the metal object.
Powering Up the SilverSaver®1000
SilverSaver®1000 User Manual8
1. Be sure the SilverSaver®Tray is in the horizontal and latched position. Empty entire contents of
plate onto the Tray.
2. If metal is detected (Detection Light (red) flashes and alarm sounds), remove all metal items
from the Tray until the alarm stops.
3. Lift the Handle to tilt the Tray so that the waste falls into the trash can.
4. Return the Tray to the horizontal and latched position.
NOTE: Aluminum foil trash items may activate the alarm. In this case, be sure there are not
also any valuable items on the Tray causing the alarm before dropping the waste into the
trash can. If foil waste continues to be an issue, please see ‘False Alarms’ on page 9.
Lights
Light Cause Action
Metal Detected Check the Tray for any metal items and remove.
Tray Open Return the Tray to the horizontal position with Handle latched.
Magnetic
Connector is
Disconnected
Ensure that the Magnetic Connector of the Control Box is securely
connected to the Magnetic Pads of the Tray and press the
Reset button .
If this does not solve the problem, read ‘Error Light (yellow) is
solid On’ on page 16 in the Troubleshooting section for further
possible causes and their solutions.
Low Battery
(page 14)
Charge the battery as soon as convenient — see ‘Batteries and
Charging’ on page 14.
Operation
SilverSaver®1000 User Manual9
When the Detection Alarm is activated but there are no valuable items on the Tray, the cause is
usually aluminum foil wrappers, creamer tops, bottle tops, etc.
The SilverSaver®1000 is initially set to Full Detection Mode, so will detect all metal items that are on
the Tray including foil. If detection of scrap foil is a problem, we recommend that supplies with foil
be re-sourced to exclude the foil. For example, creamers and butter pats can be purchased with
wax paper instead of foil.
If foil detection is still an issue, the situation may be improved by changing the Detection Mode.
Changing the Detection Mode
The SilverSaver 1000®has two Detection Modes — Full Detection Mode and Reduced Detection
Mode (RDM).
Full Detection Mode:
If foil products are not commonly found in the waste stream, use Full Detection Mode.
With the unit ON, hold down the Reset button and then press the Volume Up Button . A rising
tone and Detection Mode Light (blue) OFF indicates the unit is now in Full Detection Mode.
Reduced Detection Mode (RDM):
If waste foil is causing frequent false alarms, use Reduced Detection Mode.
With the unit ON, hold down the Reset button and then press the Volume Down Button .
A falling tone and Detection Mode Light (blue) ON indicates the unit is now in Reduced
Detection Mode.
NOTE: Due to technology constraints, some types of foil will still be detected even in
Reduced Detection Mode.
False Alarms
SilverSaver®1000 User Manual10
• Tilt the Tray after each load to make it easier to find valuable items.
• If the SilverSaver®1000 is moved to a different location, press the Reset button to quickly
re-calibrate for optimum performance in the new location.
• The best way to maximize the cost-saving benefits of the SilverSaver®is to ensure it is used
consistently — for this reason, do not leave a spare bagged trash can within easy reach of
the cleaning station. This is to discourage use of a trash can that does not have a SilverSaver®
attached. Never allow any waste to enter the trash can without passing through the
SilverSaver®.
Tips for Best Results
Andere Handbücher für 1000
2
Inhaltsverzeichnis
Andere SilverSaver Sicherheitssensor Handbücher
