Tools Required
• Safety Glasses
• Gloves
• Standard Ratchet Set
• Standard Wrench Set
• 10mm Socket
• 10mm Wrench
• Torque Wrench
• Drill
• 1/4” Drill Bit
• 2 Automotive Jack Stands
• Lift Jack (2 ton or more)
• Wheel Chocks
7www.silverwolfmotors.comSilverWolf™Vehicles Inc.
Installation or Servicing of the SilverWolf
™
TEEKON Systems Must be done by a Trained Golf Car
Technician.
Before installing or servicing READ THE FOLLOWING:
• Make Sure that the Vehicle’s Electrical System is working properly and all components such as
the Run/Tow Switch, FWD/REV Switch, Brakes, Throttle and all Wiring are in good condition and
operating to Manufacturers Standards. If not they Must be repaired or replaced before installing
the SilverWolf
™
TEEKON Kit.
• The Vehicle Solenoid Must have a Pre-Charge Resistor on it.
• The Batteries Must be in Good Condition and each Battery Must hold a Full Charge!
• Make sure the Run/Tow Switch is in the Tow position
• The Key is turned OFF and removed from the Ignition
• The Parking Brake is Engaged
• Disconnect the Main (+) Positive and (-) Negative Cable on the Vehicle’s Battery System.
• Before testing the Vehicle make sure the Rear Wheels are off the ground and supported
with Automotive Jack Stands. The Front Wheels must be Chocked.
• The area around the vehicle must be clear. Keep all People, Children and Pets away from the
vehicle when installing, servicing or testing the vehicle.
• Read the
SilverWolf™TEEKON
Installation /Service Manual and All Warning Labels before servicing
or troubleshooting this Vehicle.
• The Motor, Controller and Module are sealed and can not be opened for service. To replace these
parts call your local dealer. Opening these parts will Void the Warranty.
• Wear Safety Glasses and Gloves when installing this Controller.
• Wear a Safety Shield when working in or near the Vehicle Battery Compartment.
• Use Insulated Tools to protect from electric shock.
• Never lay or drop tools on the Batteries or in the Vehicle Battery Compartment.
FAILURE TO FOLLOW THE
WARNINGS BELOW CAN DAMAGE
THE VEHICLE AND/OR CAUSE
SERIOUS INJURY OR DEATH!
WARNING!
DO NOT SWITCH THESE CABLES!
Cable is on the Positive Controller Post
Cable is on the Negative Controller Post
CHECK
Tighten the
5 Controller
Bolts with a
Torque Wrench to
53in-lbs/6 Nm
DO NOT
OVER TIGHTEN!
Wire Terminal
Must Always be
on the Bottom!
LOCK WASHER
1
2
FLAT WASHER
CONTROLLER HARDWARE MUST BE INSTALLED IN THE ORDER SHOWN!
FAILURE TO FOLLOW THE WARNINGS BELOW CAN DAMAGE
THE VEHICLE AND/OR CAUSE SERIOUS INJURY OR DEATH!
WARNING!
Golf Carts & Utility Vehicles must use a
Pre-charge Resistor on the Solenoid!
DO NOT SWITCH THESE CABLES!
Cable is on the
Positive Controller Post
Cable is on the
Negative Controller Post
CHECK
Tighten the 5 Controller Bolts
with a Torque Wrench to
70in-lbs/8 Nm
DO NOT OVER TIGHTEN!
Wire
Terminal
Must Always
be on the
Bottom!
LOCK
WASHER
FLAT
WASHER
1
2
CONTROLLER HARDWARE MUST BE INSTALLED IN THE ORDER SHOWN!
CLUB CAR®PRECEDENT®/ONWARD®
INSTALLATION INSTRUCTIONS
SILVERWOLF MOTORS INC.
PATENTS PENDING
AC-PM MOTOR
TECHNOLOGY BY
ACCELERATED SYSTEMS INC
PART #
10-000784
SERIAL #
SW12001
VOLTAGE
48-72V
HP
12
RATING
5500RPM
MADE IN CANADA
™
