Simer Battery Backup System A5000-04 Bedienungsanleitung

OWNER’S MANUAL

Battery Backup System

NOTICE D’UTILISATION

Système de secours à batterie

MANUAL DEL USUARIO

Sistema de batería de respaldo

5760 0108

A5000-04

Installation/Operation/Parts

For further operating, installation,

or maintenance assistance:

Call 1-800-468-7867 /

1-800-546-7867

English . . . . . . . . . . . . . . Pages 2-11

Installation/Fonctionnement/Pièces

Pour plus de renseignements

concernant l’utilisation,

l’installation ou l’entretien,

Composer le

1 (800) 468-7867 /

1 (800) 546-7867

Français . . . . . . . . . . . Pages 12-21

Instalación/Operación/Piezas

Para mayor información sobre el

funcionamiento, instalación o

mantenimiento de la bomba:

Llame al 1-800-468-7867 /

1-800-546-7867

Español . . . . . . . . . . .Paginas 22-31

293 Wright St., Delavan, WI 53115

Phone:

1-800-468-7867

1-800-546-7867

Fax:

1-800-390-5351

Safety 2

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

READ AND FOLLOW

SAFETY INSTRUCTIONS!

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for

one of the following signal words and be alert to the

potential for personal injury!

warns about hazards that will cause

serious personal injury, death or major property damage

if ignored.

warns about hazards that can cause serious

personal injury, death or major property damage if

ignored.

warns about hazards that will or can cause

minor personal injury or property damage if ignored.

The word NOTICE indicates special instructions which

are important but not related to hazards.

1. To avoid risk of serious bodily injury due to electrical

shock or burns and property damage due to flooding,

read the safety instructions carefully before installing

pump.

Battery acid is corrosive. Do not spill on

skin, clothing, or battery charger. Wear eye and head

protection when working with battery. Connect and

disconnect DC output terminals only after removing the

charger from the AC outlet. Never allow the DC termi-

nals to touch each other.

Hazardous Voltage. Can cause severe or

fatal electrical shock. Do not plug in or unplug battery

charger while standing on a wet floor or in water. Be

sure one hand is free when plugging in or unplugging

charger. If basement floor is wet, disconnect power to

basement before walking on floor.

Risk of flooding. Do not run pump dry. To

do so will damage seals and can cause leaking and prop-

erty damage.

2. Follow local and/or national plumbing and electrical

codes when installing the system. A ground fault

circuit interrupter (GFCI) is recommended for use on

any electrical appliance submerged in water.

3. Use this system only for backup sump pump duty in

a residential application. It is not designed as a

primary sump pump.

4. Do not lift pump by electrical cord.

Risk of electrical shock. Do not lift the

pump by the electrical cord; lift pump only by the

discharge pipe, lifting ring or handle on the pump. Lifting

by the cord can damage the cord.

5. Pump clear water only with this pump.

6. Pump is permanently lubricated at the factory. Do

not try to lubricate it!

7. Keep battery charger and battery box off of the floor

and in a dry, cool, well ventilated area.

NOTICE: If a Carbon Monoxide (CO) sensor is

installed, it must be at least 15 feet away from

battery charger in order to avoid nuisance CO

alarms. Please refer to your CO detector’s installation

guidelines for more information.

8. To avoid danger of fire or explosion, keep sparks and

flame (pilot light) away from battery.

9. Maximum vertical pumping distance is 16 feet

(4.9M) for Model A5000-04.

10. Make sure sump is clear of debris. Debris can

damage the pump which can result in flooding.

GENERAL INFORMATION

The battery back-up sump system is not a substitute for

your primary sump pump. It is designed to temporarily

back up your primary sump pump during a power

outage or other problem which prevents normal opera-

tion of the primary pump. Do not use this system to

pump flammable liquids or chemicals. Pump clear water

only with this pump.

Keep the battery charger dry and protected from damage.

This system is designed to work with a deep cycle

marine battery, either a flooded lead-acid battery or a

sealed maintenance free lead-acid AGM battery. In an

emergency (such as an extended power outage) which

depletes the system deep cycle battery, your automobile

battery may be temporarily substituted. Be sure to

replace the system deep cycle battery as soon as

possible. Use of an automobile battery instead of a deep

cycle battery in this system will significantly reduce the

system’s total performance. Automobile batteries are not

designed for this type of application and will be quickly

ruined by the repeated charge/discharge cycling.

NOTICE: This system is not designed for applications

involving salt water or brine! Use with salt water or brine

will void warranty.

Installation 3

BATTERY BACKUP SYSTEM (BBU)

INSTALLATION AND OPERATION

NOTICE:

• Install this system during a time when the primary

pump will not be needed. Gather all supplies before

starting. Read all warnings and installation steps

before you start.

• Be prepared for water to leak from the coupling or

piping when disassembling or cutting the discharge

pipe. Protect system components, tools and supplies

from getting wet. Dry any work areas that get wet.

BASIC TOOLS AND

MATERIALS NEEDED

Channel locks or large pliers

Tape measure

Socket wrench or 5/16” Nut driver

Side cutters

Hacksaw (to cut PVC pipe)

Medium size pliers

Pencil

Teflon tape

PVC glue (solvent weld)

PVC pipe cleaner

Cloth towel

100-120 Ampere-Hour Marine Deep Cycle Battery

(sold separately)

Required Battery Capacity:

Single Battery: 120 ampere-hour maximum.

Double Batteries: 100 ampere-hours per battery

(200 ampere-hours total)

Personal injury and flood hazard. Do not

turn the pump on until all the fittings are glued and the

glue has dried. Loose fittings can explode off of pipes

and cause personal injury and flooding.

RETAIN ORIGINAL RECEIPT FOR YOUR RECORDS.

LIMITED WARRANTY

SIMER warrants to the original consumer purchaser (“Purchaser” or “You”) of its products that they are free from defects in material and workman-

ship for a period of twelve (12) months from the date of the original consumer purchase.

If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at

SIMER’s option, subject to the terms and conditions set forth below. The original purchase receipt and product warranty information label are

required to determine warranty eligibility. Eligibility is based on purchase date of original product – not the date of replacement under warranty. The

warranty is limited to repair or replacement of product only – Purchaser pays all removal, installation, labor, shipping, and incidental charges.

For parts or troubleshooting assistance, DO NOT return product to your retail store. Contact SIMER Customer Service at 1-800-468-7867 /

1-800-546-7867.

Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet where it was

purchased immediately after the discovery of any alleged defect. SIMER will subsequently take corrective action as promptly as reasonably

possible. No requests for service will be accepted if received more than 30 days after the warranty expires.

SEWAGE PUMPS

DO NOT return a sewage pump (that has been installed) to your retail store. Contact SIMER Customer Service. Sewage pumps that have seen

service and been removed carry a contamination hazard with them.

If your sewage pump has failed:

• Wear rubber gloves when handling the pump;

• For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;

• Dispose of the pump according to local disposal ordinances.

Exceptions to the Twelve (12) Month Limited Warranty

Product Warranty Period

BW85P, CM10, CMK, M40, M40P 90 days

2300, 2310, 2330, 2520ULST, 2955, 2956, 2957, 2960, A5500 2 Years

4” Submersible Well Pumps, 2958, 2975PC, 2985, 3075SS, 3983, 3984 3 Years

Pre-Charge Water System Tank, 3985, 3986 5 Years

3963, 3988, 3995, 3997 Lifetime

General Terms and Conditions

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not apply to the following:

(1) acts of God; (2) products which, in SIMER’s sole judgement, have been subject to negligence, abuse, accident, misapplication, tampering, or

alteration; (3) failures due to improper installation, operation, maintenance or storage; (4) atypical or unapproved application, use or service;

(5) failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of recommended maximums.

This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING BUT

NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING

WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so

the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may also have other rights which vary

from state to state.

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867 / 1-800-546-7867 • Fax: 1-800-390-5351

E-Mail: inf[email protected] • Web Site: http://www.simerpumps.com

Installation 4

BBU INSTALLATION INSTRUCTIONS

Risk of electrical shock. At the circuit breaker

or fuse box, turn off the electrical power to the sump

pump before beginning this installation.

Setup

1. Locate the high water level in your sump pit (that is,

the water level at which the existing (primary) sump

pump starts - see Figure 1). Mark this point on the

discharge pipe with a pencil or marker.

2. Drain the sump pit as far as possible without running

the pump dry. Do this by:

A) PIGGYBACK SWITCH: Unplug the pump and switch

from the outlet, then unplug the pump from the

piggyback switch. Reset the circuit breaker or

reinstall the fuse and plug the pump directly into

the outlet. The pump will start. Drain the pit and

unplug the pump. OR

B) NO PIGGYBACK SWITCH: Reset the circuit breaker or

reinstall the fuse and use a non-conducting

broom handle or stick to raise the float switch;

the pump should start. Drain the pit and then

release the switch.

C) ALL INSTALLATIONS: When the pit has drained, turn

off (open) the circuit breaker or remove the fuse

again to avoid electrical shock while working on

the installation.

3. Support the discharge pipe so that it can’t collapse

when you take it apart or cut it.

4. If your discharge pipe has a hose coupling, discon-

nect the coupling. If not, cut the vertical discharge

pipe at any convenient spot above the floor level.

5. Lift the pump and attached pipe out of the sump pit.

Installation

1. Study Figure 2 for suggested layouts.

The Easy-Install layout works better for deeper

sumps and allows a smaller diameter sump (diameter

13-1/2” or larger, depth more than 22”).

The Alternate layout works better for wider, shal-

lower sump pits (diameter 18” or larger, depth 18-

22”). The Alternate layout will require that you

purchase (2) 1-1/4” x 90° elbows and (2) 1-1/4” x

close pipe nipples.

Other layouts may require more pipe fittings.

2. Find the high water level mark you made on the

discharge pipe in “Setup, Step 1”. Cut the pipe at this

point and set the cut-off piece aside for use later.

Clean up and debur the cut ends.

3. Wrap the threads of the Battery Back Up pump (BBU

pump) and the 1-1/4” x close nipple with 1-1/2 – 2

turns of teflon tape (see Figure 2). Leave the first

thread free of tape and wrap clockwise ( ).

4. Thread the tee, the close nipple, the 1-1/4” x 1-1/4”

check valve, and the BBU pump together. To get

them tight, hold the pump and insert a large screw-

driver down through the tee and tighten the whole

assembly with the screwdriver. DO NOT OVERTIGHTEN!

When the assembly is tight, the pump and tee should

align vertically (no twist – see Figure 2).

5. Glue the cut-off piece of pipe (which you set aside

in Step 2) into the top of the tee.

NOTE: If your discharge pipe is 1-1/4” inch, glue one

of the reducer bushings supplied with the system into

the tee, then glue the pipe into the bushing.

6. Look at your primary pump to determine if you have

a check valve in or near the pump discharge. If not,

install the auxiliary check valve in the bottom arm of

the tee and install the slip coupling on the check

valve (see Figure 2). For 1-1/4” discharge pipe, glue

the remaining reducer bushing into the slip coupling.

NOTE: If the primary pump assembly already

includes a functioning check valve, do not use the

auxiliary check valve included in the BBU system.

You need one check valve between the primary

pump and the tee (to prevent backflow from either

pump into the sump pit), but two check valves will

restrict the pipe too much.

7. Trial Fit (NO GLUE YET): Place the primary pump

assembly back in the sump pit and add (dry) the

tee/check valve/BBU pump assembly to it. If neces-

sary, also include the 1-1/2 x 1-1/4 reducer bushing

and the slip coupling and auxiliary check valve (see

“NOTE”, above).

8. Measure the assembly against the hanging upper

discharge pipe (where you cut it in Step 1 under

“Setup”). Mark the discharge pipe coming up from

the tee 1/4” below the point of overlap (that is, you

should have an air gap of 1/4” after you cut the

pipe). Don’t cut anything yet.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

‘Start’ water level

of Primary Pump

Sump Pit

Check

Valve

Support the

Pipe before

cutting.

Mark pipe with

pencil here.

Figure 1: Mark pipe at ‘start’ water level

Installation 5

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Primary Pump Discharge

Pipe (cut to fit)

Primary Sump Pump

Discharge Port

Primary Sump Pump

Check Valve

Flow Arrow; Must point

AWAY from Pump being

Protected

1-1/2"x1-1/4" Slip Reducer

Bushing*

1-1/2"x1-1/2" Slip Coupling*

Not to scale;

wiring omitted

for clarity.

1-1/2"x 1-1/2" slip x

1-1/4" FNPT Tee* 1-1/4”x1-1/4”

Check Valve

Assembly*

Teflon tape all

threaded joints

Battery Back Up

Sump Pump*

Auxiliary Check Valve*

(

See Important Check Valve

Warranty Note, Below

)

Alternate Installation

for a Shallow Sump

“Easy Install” Layout

5763 0108

†

1-1/4”x1-1/4”

Close Nipple*

Switch with Clamp*

Notes:

†

* Supplied with the Battery Backup System.

Use if necessary to adapt a 1-1/4” discharge pipe to the 1-1/2” fittings supplied.

Use to adapt the auxiliary check valve to the discharge pipe.

Water level when the switch shuts off must be above the BBU pump intake.

Discharge pipe

cutoff piece

Upper Discharge pipe

Hose Coupling with Clamps*

1-1/2"x1-1/4" Slip

Reducer bushing*

†

Check Valve Flapper(s) must swing in direction shown.

Flow arrow(s) must point AWAY from pump being protected.

The 1-1/4” X 1-1/4” Check Valve Assembly must be installed

as shown or the warranty is void. Do not use a wrench (see

Installation Step 4, Page 4)! If the Primary Sump Pump

does not have a check valve installed as shown below the

Tee, the Auxiliary Check Valve must be installed as shown

or the warranty is void.

IMPORTANT CHECK VALVE/WARRANTY NOTE:

Figure 2: Typical Installation Layouts

Installation 6

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

9. Study the assembly in the pit for a moment and then

adjust it so that nothing interferes with the primary

pump or its switch. Mark the joints with a permanent

marker so that you can realign everything after you

pull it out of the pit for gluing (see Figure 3).

NOTE: Take your time with this - it takes care but

isn’t very difficult. Be sure you leave enough room

for the BBU pump’s vertical switch. Mark everything

that might move!

10. After you have marked everything, remove the

assembly from the pit.

11. Cut off the vertical discharge pipe at the cut point

you marked in Step 8. BE SURE YOU ARE CUTTING ON

THE RIGHT MARK!

12. Recheck the alignment and glue up all the joints on

the primary pump assembly.

NOTE: You may need to support the assembly,

which won’t balance very well, in order to preserve

the alignment while gluing it. Check this before you

start gluing. Another pair of hands may help here!

13. After the glue has set, slide the hose coupling and its

clamps down over the assembled discharge pipe. If

the pipe is 1-1/4”, be sure to use the two reducing

inserts included with the coupling.

14. Hook the switch clamp over the switch bracket and

slide the assembly down over the hose coupling and

discharge pipe. Clamp the switch so that the water

level when the switch shuts off is above the BBU

pump’s intake.

15. Replace the assembly in the pit, slide the hose

coupling up over the air gap so that it joins the pipes,

and tighten the clamps enough to keep it there.

16. Check fit, alignment, etc. If everything looks good,

make sure that the BBU vertical switch is at the right

height and free of obstructions, then tighten the hose

clamps on the coupling.

17. Adjust the rod stop location on the BBU float rod to

give the desired switch travel. If necessary, nip off

the bottom of the float rod to provide clearance.

BBU WIRING AND SETUP

See Figures 4, 5, and 6 for battery installation and

connection information.

Figure 3: Mark joints for gluing

57680108

Battery

Inputs

Figure 4: The battery input is inside the battery case.

Support the case when opening it. The support must be

at least 4” thick.

Figure 5: Install the battery in the case. Have someone

support the case while you do this. Once the battery is in

the case, connect the leads from the charger/controller:

+(Red) to +(Red), and –(Black) to –(Black).

Installation 7

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

1. The pump leads are polarity sensitive; connect the

positive pump lead to the terminal labeled ‘Pump +’

and the negative pump lead to the terminal labeled

‘Pump –’.

NOTE: If the leads are reversed, the pump will run

backward and not pump water.

2. The vertical float switch leads are not polarity sensi-

tive; connect the float switch leads to the ‘Float

Switch’ tabs on the Charger/Controller. If you are

using two batteries, use the second set of terminals

and connect the second battery in the same manner.

Connect the

positive

(+) battery lead (red) to the

positive Charger/Controller terminal (red). Connect

the

negative

(–) battery lead (black) to the negative

terminal (black) on the Charger/Controller.

3. Test the float switch and the pump by lifting and

holding the float rod. The ‘Pump Status’ LED will

light continuously and the buzzer will beep steadily.

The pump should start after 3 seconds. If the pump

does not run, check all the connections and remake

them as necessary.

4. With the pump operating, press the ‘Silence Alarm’

button; hold for one second; release. The ‘Silenced

Alarm’ LED should illuminate and the buzzer should

stop sounding. To reset the buzzer (make it sound)

and extinguish the ‘Silenced Alarm’ LED, press the

‘Silence Alarm’ button again for one second.

5A. To stop the pump, lower the float switch; after 3

seconds the pump should stop, the ‘Pump Status’

LED should flash, and the buzzer should beep.

5B. Depress the ‘System Test’ button; hold it for one second;

release. The ‘Pump Status’ LED should stop flashing.

NOTE: During normal operation, the flashing ‘Pump

Status’ LED indicates that the pump has run in your

absence. See Table II, “Operating Code Displays”,

Page 9.

6. Press and hold ‘System Test’ button. All LEDs will

light up, pump will run and buzzer will sound.

Release the button and LEDs should go off, pump

should stop, buzzer should stop.

7. The ‘Battery Status’ LED indicates the battery

capacity when the A.C. power is off.

A. Continuously ‘ON” - the battery voltage is above

10.9 Volts Direct Current (10.9VDC) and

capacity is above 20%.

B. Slow Beep/Slow LED Flash - the battery’s

capacity is between 0 and 20%.

C. Fast Beep/Fast LED Flash - the battery is severely

discharged. The battery will continue to charge

(as long as the 115V AC power to the charger is

on) at the rate of .5 AH until the battery’s charge

is above 20%.

When the first warning occurs (slow beep/slow

flash), you will have approximately 2 hours (or less)

of pump operation left. The actual time of operation

will depend on the condition of the battery and may

be as little as 15 minutes.

8. Connect the Power Supply cable (supplied) to the

Charger/Controller’s Power Input jack.

LED Display and Control Buttons

(Tables II, III, IV, and V)

NOTE: When the unit is first plugged in, or when it first

receives power from the battery, the Battery Status LED

will flash for 3 seconds.

NOTE: To activate any Control Button, depress and hold

it for 1 second.

Possible Remedies

1. Wrong Battery Voltage

Reconnect charger to a 12 volt battery.

2. Reversed Battery Connections

Check all connections. The negative (black) on the

battery must connect to the negative (black) on the

charger, and the positive on the battery must connect

to the positive on the charger. Reversing the battery

connections will cause the ‘System Alert’ and

‘Silenced Audible Alarm’ LEDs to flash.

3. Thermal Runaway Condition

“Thermal Runaway” is the technical term for the

condition of the battery when some (or all) of the

cells have deteriorated to the point that they won’t

take a charge. In this case, replace the battery.

4. Charge Time Monitor – 1 and 2

Battery took too long to complete its charge. The

‘Charge Time Monitor’ will shut down the charger

after 84 hours of continuous charging.

Possible causes are:

A) Pump ran for a long period of time during

charging, or

B) Battery is too large for the charger (including

several batteries connected in a parallel circuit).

Apply the formula in Table I to determine whether

or not your battery is too large for the charger. If the

calculated charging time is more than 84 hours, use

a smaller battery (or group of batteries).

Figure 6: Close and latch the case while holding it in

position.

Installation 8

Excessive Battery Drain

Pump may have run for a very long time, discharging the

battery. In this case:

A) If 115VAC power is OFF, the charger shuts down

until the power comes back on, but the pump

will run as long as the battery charge lasts. You

may need to replace the battery afterwards.

B) If 115VAC power is ON, the charger/controller

continues to try to charge the battery at a

charging rate of .5 AH until the battery charge is

more than 20%, at which point the charger will

resume charging at a rate of 2 AH.

C) If the pump is running and the AC power is on,

you may need to stop the pump to allow the

battery to charge.

Pre-Qualification Test – 1 and 2

Charger is charging at a very low level to try to bring a

dead battery back to life. If the battery is taking too long,

try resetting the charger once or twice (push the ‘System

Test’ and ‘Silence Alarm’ buttons to reset the charger).

Special Features:

• The charger is equipped with reverse battery, short

circuit, and “run-away charge” protection.

BATTERY REQUIREMENTS

Hazardous electrical current. Can cause

severe burns and start a fire if the battery terminals are short

circuited. Install the battery in the battery case (See Key No.

12, Page 11). To prevent accidental shorting across battery

terminals, close and latch the battery case securely. Do not

leave the battery uncovered. Do not allow children to play

around the battery backup system installation.

Your backup sump pump depends on the battery used

with it for power. The better the battery, the better the

performance of the pump. We recommend the use of a

size 27M Marine Deep Cycle Battery. It will perform as

indicated in Table VI, on Page 10, and will stand up well

to long periods of little or no use.

This system is designed to work with a deep cycle

marine battery, either a flooded lead-acid battery or a

sealed maintenance free lead-acid AGM battery. Use of a

standard automobile battery with this charger is not

recommended. An automobile battery may require

charging after only 1–2 hours of continuous use, and the

repeated charging cycles may cause early plate failure in

the battery.

Use only the recommended battery or one of the same

type and size so it will fit in the battery box (maximum

size 13" long, 7" wide and 10" high [330.2mm x

177.8mm x 254mm] including terminals) and supply

enough voltage for full performance.

BATTERY MAINTENANCE

Severe burn hazard. An acid-filled standard

lead-acid battery contains sulfuric acid. Avoid contact with

skin, eyes or clothing.

NOTICE: To protect the battery case from chipping and

gouging, do not let the battery sit on a concrete floor.

Install the battery on a shelf or protective pad (plywood,

2x4s, etc.). Always install the battery in a dry location

that is protected from flooding.

Follow the battery manufacturer’s recommendations for

maintenance and safe use of the battery.

TROUBLESHOOTING

Pump won’t run.

1. Check all the wiring connections.

2. Check for a low or defective battery.

3. Check that the automatic switch is free to move up

and down.

4. Press the circuit breaker reset button on the control

panel.

Motor hums but pump won’t run:

1. Check for low or defective battery.

Pump runs but pumps very little or no water:

1. Make sure a check valve is installed and functioning

between the primary pump discharge and the Battery

Backup tee.

2. Check for an obstruction in the discharge pipe.

3. The discharge pipe length and/or height exceeds the

capacity of the pump. See Table VI, Page 10, for

pump capacity.

4. Check for a low or defective battery.

5. The Positive (+) and negative (–) pump wires are

reversed. Disconnect them and reconnect correctly.

Pump cycles too frequently:

The check valve located between the discharge of

the primary pump and the Battery Backup tee is not

installed or is not working properly. Install the auxil-

iary check valve (see Pages 4 and 5) or replace the

existing check valve as required.

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

2 Amperes

130 Ampere Hours

130H 65H

80H

81.25 Hrs

Less than 84 hours to charge; OK to use.

2 Amperes

160 Ampere Hours

160H 100Hrs

Capacity too large – use a battery of 130A-H or less.

NOTE: A 100AH battery in good condition should charge

in approximately 62 hours.

Example 1:

Example 2:

5764 0108

TABLE I – Battery Capacity Calculation

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Installation 9

LED Operating Code Display System Operating Condition

Charging

Battery status

Pump status

C power

Silenced audible alarm

System Alert

Indicates 115VAC Power is connected

NOTE: All of the situations listed above indicate normal system operation; no action is required.

However, if the BBU pump is running or has run, check the primary pump and actively monitor the

charger status for battery life. Always reset the charger after the pump runs.

During normal system operation, the ‘System Alert’ LED does not light up. The “AC Power” LED

is lighted as long as the system is plugged in to an operating AC power circuit.

Indicates Pump is running (continuous LED)

Indicates Audible alarm is switched off

Indicates Battery is charging normally

Indicates Continuous LED: battery charge is above 20%,

system is maintaining charge

Indicates Slowflashing LED: battery charge is below20%

LED is Flashing (Slow)

=LED is OFF

LED is ONContinuously

= =

LED is Flashing (Fast)

Indicates Fast flashing LED: Pump has run

Indicates Fast flashing LED: Battery pre-qualification test is running

TABLE II – Operating Code Displays (LEDs Lighted Continuously or Flashing)

Control LED: Continuous Illumination Indicates Normal Operation:

AC Power AC power is present.

Pump Status

The float switch has been activated. The LED remains on (flashing) after the pump

has stopped. Depress the‘System Test’ button to reset it.

Silenced Audible Alarm Audible Alarm has been silenced. Press and release the ‘Silence Alarm’ button to

reset (activate) the audible alarm and turn OFF the LED.

Charging

Indicates that the battery is charging – see Table II, above.

Battery Status A. Continuous ‘ON” - the battery voltage is above 10.9 Volts DC and capacity is

above 20%.

B. Slow Beep/Slow LED Flash - the battery’s capacity is below 20%, and voltage

is between 8.2VDC and 10.9VDC.

C. Fast Beep/Fast LED Flash - the battery has been discharged to less than

8.2VDC.

System Alert Flashing (in unison with the buzzer) indicates that the charger has entered ‘Failure

Mode’. Press the ‘System Test’ and ‘Silence Alarm’ buttons to reset it.

NOTE: If the source of the failure is not corrected, the charger will reenter ‘Failure

Mode’. See Table IV for error code information.

TABLE III – LED Function Displays (LEDs Lighted Continuously)

Installation 10

For parts or assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Charging

Battery status

Pump status

AC power

Silenced audible alarm

System Alert

= Excessive battery drain; Stop pump, allowbattery to charge (AC must be on)

= Battery will not take a charge***; Replace battery with a new12Vlead-acid battery

= Charge time monitor – 1; Check battery for damage to cells; replace battery

= Reversed battery connections; Connect + to + and – to –.*

= Wrong battery voltage; Replace battery with a new12Vlead-acid battery

= Charge time monitor – 2; Check battery for damage to cells; replace battery

= Failed pre-qualification test – 2**; Replace battery with a new12Vlead-acid battery

= Failed pre-qualification test – 1**; Replace battery with a new12Vlead-acid battery

LED Error Code Display

Condition Action

Error Condition and Corrective Action

NOTE: When the ‘System Alert’ LED is flashing,

look for one of the following error conditions.

* NOTE: If your AC power is off and the unit is dead (no LEDs lighted, no audible alarm, pump isn’t running),

check for reversed battery connections to the charger/controller.

** Charger was charging at a very lowlevel to try to bring a dead battery back to life, but the battery took too long

to charge. Try resetting the charger once or twice (push the ‘System Test’ and ‘Silence Alarm’ buttons at the same

time to reset the charger).

*** Thermal Runaway condition

LED is Flashing (Slow)

=LED is OFF

LED is ONContinuously

= =

5766 0108

=Battery Charge is Below20%; Pump will shut down, battery is not charging. Replace

battery.

LED is Flashing (Fast)

TABLE IV – Error Code Displays (LEDs Flashing)

VERTICAL PUMPING DISTANCE - MODEL A5000-04

8 FEET (2.4 M) 10 FEET (3.0 M) 12 FEET (3.7 M) 16 FEET (4.9 M)

Gallons Per Hour 1,440 1,200 840 No Flow at this Height

Aproximate Hrs Available 10 11.5 13 –

Total Gallons Pumped 8,500 7,000 5,000 –

TABLE VI – Capacity Ratings with a 100 A-H Deep Cycle Marine Battery

* These flow rates were obtained with a constant 12.7 VDC battery source. The actual GPH will vary due to a reduction in

output voltage from the battery as it discharges.

Control Button: Result of Pushing Button:

System Test Pump starts and all LEDs light up.

Will reset the ‘Pump Status’ LED.

When pushed with the ‘Silence Alarm’ button, the Charger/Controller

microprocessor resets and error code resets.

Silence Alarm Toggle; Prevents the audible alarm sounding. Press and release to reset.

Flood Light Toggles the flood light on the Charger/Controller on and off.

TABLE V – Control Button Functions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Simer Kamerazubehör Handbücher

Simer

Simer A5200 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung