Simplex SIMPLEX 500 Bedienungsanleitung

QUARTZ TIME RECORDER

OPERATION MANUAL

Simplex 500

All manuals and user guides at all-guides.com

all-guides.com

The details of this Operation Manual are subject to change w ithout previous

notification.

This Operation Manual has been prepared with the utmost care to cover all aspects of

the time recorder's use.

If you feel, however, that some explanations are inadequate, unclear, or difficult to

understand, please do not hesitate to contact the dealer or the shop from which you

have purchased your Time Recorder.

Be sure to use your Time Recorder after you have fully understood the hardware and

software specifications and limits.

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted, in any form or by any means, mechanical, photocopying, recording or

otherwise.

Replace battery with TOSHIBA, part no. CR 2450 THC only.

Use of another battery may present a risk of fire on explosion.

Place the time recorder close to the wall outlet so that it is easily accessible to

disconnect.

Bescheinigung des Herstellers/Importeurs

Dies Gerät entspricht den Bedingungen der Niederspannungs-Vorschrift

73/23/EEC und dem EMVG nach 89/336/EEC.

This unit complies with the Low Voltage Directive 73/23/EEC and the

EMC Directive 89/336/EEC.

Maschinenl ärminformationsverordnung 3. GSGV, 18.01.1991:

Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A) oder

weniger gemäß ISO 7779.

Die zugeho¨rige Steckdose muß nahe beim Gerät angebracht und leicht

zugänglich sein.

All manuals and user guides at all-guides.com

TABLE OF CONTENTS

PRECAUTIONS

FEATURES

BEFORE USING THE TIME RECORDER

Accessories

Features

Installing the Ribbon Cassette

Wall Mounting

Environmental Conditions

DAILY OPERATIONS

SETTING

Preparation for setting

Setting the Pay Period

Setting the Date and the Time, 1/60 or 1/100 printing,

and the 12/24 HOUR format

Setting the Day Advance Time

Setting the Daylight Saving Time (D.S.T.)

Setting the Time Table Program

Setting Number of Seconds for External Time Signal

Resetting

CONNECTING TO AN EXTERNAL TIME SIGNAL

INSERTING THE Ni-Cd BATTERY

TROUBLESHOOTING

SPECIFICATIONS

TIME CARD SPECIFICATIONS

10.

All manuals and user guides at all-guides.com

1. PRECAUTIONS

Signs

Various warnings and cautions are provided throughout this manual along with signs.

Remember each sign and its explanation listed below for your safety and proper

operation of the unit.

Caution

Warning

Improper handling may cause electric

shock DANGER.

DO NOT disassemble the unit.

"Don't" sign.

"Must-Do" sign.

Be sure to remove the line cord plug

from the outlet.

Do not disassemble the unit. There is a high voltage present inside, possibly leading to an

electric shock.

Do not use any voltage of the power source other than designated.

Do not share a single outlet with another plug. These may lead to fire or shock hazards.

Do not damage, break, or modify the power cord. Do not put a heavy object on, pull, or

forcefully bend the cord, either. These may damage the cord, possibly resulting in a fire or

electric shock.

If any anomaly occurs, for example, heat or smoke is generated or an odor is emitted, unplug

the unit immediately and contact your dealer for servicing. There is a danger that further use

may cause a fire or electric shock.

Do not modify the unit. Modifications may cause a fire and/or electric shock.

Warning

Improper handling may cause bodily accidents including

death and serious injury.

Improper handling may harm the human body or material.

This operation manual is prepared for safe and proper use of the unit.

Please follow all the instructions to avoid possible danger to yourself

or others and damage to the unit.

All manuals and user guides at all-guides.com

2. FEATURES

The time table program provides the following functions:

•Automatic switching between black and red printing

The two-color printing system makes it possible to easily see an

employee's in and out time.

•Automatic activation of an external time signal

The unit can be programmed to externally output a signal when

it's time to start or quit, or for breaks.

•Automatic switching among six print columns (Columns 1-6)

The auto-switching function of a column to print records in

prevents punching failure or error.

It has three selectable pay periods : weekly, bi-weekly or monthly.

The monthly card automatically senses the front or back of the card,

therefore assuring no erroneous date printing.

If the closing date for payroll processing does not fall on the end

of a month, the unit can be set to any desired closing date.

The day advance time function makes it possible to print out on

the same line of a time card for the previous working day even

when leaving the office after midnight.

An easy-to-see analog clock is provided on its front for users'

convenience.

User-friendly operation and easy setting enhance users' comfort.

•

All manuals and user guides at all-guides.com

Features

Daylight saving time indication

Current date

SU MO TU WE TH FR SA

Day of the week indication

Current time AM or PM

BEFORE USING THE TIME RECORDER

Accessories

Operation Manual Wall mount fittings

Ribbon cassette

Keys

Card slot

Display

Control button

Panel cover

Analog clock

Panel open button

(at both sides

of the unit)

Key hole

Wall-mounting

hole

12Hr.

12 HOUR indication

All manuals and user guides at all-guides.com

all-guides.com

Panel cover

Installing the Ribbon Cassette

1Unlock the unit. While holding

down the panel, open buttons at both

sides of the unit, and lift the panel

cover away from you.

2Turn the knob on the cassette in the

arrow-indicated direction to make the

ribbon taut.

To insert the ribbon cassette inside

the unit, lift the panel house away from

you first. Then thread the ribbon

between the ribbon mask and the print

head. Slide the latch on the lower side

of the cassette into projections on the

unit. Then let the cassette snap into

place.

When having difficulty inserting the

ribbon, insert it while turning the knob.

Make sure that the ribbon is placed

between the print head and the ribbon

mask as illustrated in the figure at left.

Put the panel cover on the hook at

the back of the unit. Lower it toward

this side to close and lock the unit.

Panel cover

Panel open button

(at both sides of the unit)

Key hole

Panel house

Ribbon cassette

Print head

Ribbon

Ribbon mask

All manuals and user guides at all-guides.com

Wall Mounting

The unit can be mounted on a wall using the supplied mounting fittings. To mount the

unit on a wall, take the following steps:

The supplied screws are intended

for use on a thick wooden wall or

wooden column. Do not use

them on any other materials.

There is a danger that the unit

may come off.

1Install the two larger screws into a wall

3.94 inches (10 cm) apart. Be sure to keep

about 0.12 inch (3 mm) of the screw head

out of the wall.

2Mount the wall mount fittings

as shown on the right.

Environmental Conditions

Avoid placing the unit in environments that are:

•humid or dusty

•exposed to direct sunshine

•subject to frequent or continuous vibrations

•outside the temperature range between -5° and 45°C

•affected by chemicals or ozone

3.94" (10cm)

0.12"

(3mm)

All manuals and user guides at all-guides.com

Once the AC line cord is plugged into the outlet, the unit can be used immediately as

basic operation has been pre-set at the factory, including the time and the closing date.

See "3 BEFORE USING THE TIME RECORDER".

Do not let any metallic object get into the slot, including paper clips. Do not

forcefully push in a card, either. These may cause the unit to malfunction.

4. DAILY OPERATIONS

It is easy to operate the unit. Just insert a time card. The card is then automatically

pulled in, printed and then ejected.

The unit is designed to print in black on the first column when no time table program

is set. Usually it is necessary to set the time table program in order to automatically

print colors and to change columns to print records in. For a temporary change of a

column, however, manual operation is also available: just push the button for any

desired column before inserting a time card.

The button for the column selected lights up.

If any setting needs to be changed, such as for a closing date or other items, See "5.

SETTING".

All manuals and user guides at all-guides.com

To prepare for setting:

5. SETTING

Preparation for setting

1Unlock the unit. While holding down

the panel, open buttons at both sides of the

unit and lift the panel cover away from

you.

2Remove the panel cover.

3Make settings using the display and

control buttons at the panel house.

Panel house Control buttonDisplay

Be sure to make settings with

the power on.

Make sure to press SET at the completion of each setting. Contents are NOT stored in

memory if SET is not pressed.

Upon opening the panel cover, the PAY ENDING button lights up and the unit is in

the pay ending setting mode.

Panel cover

Key hole

Panel open button

(at both sides of the unit)

All manuals and user guides at all-guides.com

Andere Handbücher für SIMPLEX 500

Inhaltsverzeichnis

Andere Simplex Uhr Handbücher

Simplex

Simplex Acroprint 175 Installationshandbuch

Simplex

Simplex EP40 Bedienungsanleitung

Simplex

Simplex EP800 Bedienungsanleitung

Simplex

Simplex 6311-1234 Bedienungsanleitung

Simplex

Simplex Simplex Centennial Recorder Installationshandbuch

Simplex

Simplex 300 Bedienungsanleitung

Simplex

Simplex Ethernet Clock Bedienungsanleitung

Simplex

Simplex Simplex Heritage Installationshandbuch

Simplex

Simplex Simplex Consecutive Bedienungsanleitung

Simplex

Simplex 6311-1234 Bedienungsanleitung

Simplex

Simplex EP10 Bedienungsanleitung

Simplex

Simplex 6310-9221A Bedienungsanleitung

Simplex

Simplex SIMPLEX 500 Bedienungsanleitung

Simplex

Simplex 6500 Bedienungsanleitung

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256-AL Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

La Crosse Technology

La Crosse Technology WT-3141b Handbuch

La Crosse Technology

La Crosse Technology W86531 Bedienungsanleitung

Sharp

Sharp SPC900 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-50447 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung

LG LEC-005 Bedienungsanleitung