Simrad RF25 Bedienungsanleitung

Instructions

RF25 Rudder Feedback (P/N 22014302)

GENERAL

The RF25 is designed for connection to the

SimNet network. It is equipped with

transmission link and 5 m (16 feet) of SimNet

cable with connector. It transforms the

angular travel of the rudder to a digital signal

read by the autopilot steering computer. The

RF25 transmits the rudder angle even if the

autopilot is switched off.

INSTALLATION

The RF25 Rudder feedback unit mounts close

to the rudder, and is mechanically linked to

the rudder tiller arm or rudder quadrant. Refer

to the figure below for recommended

mounting arrangement.

Do not remove the transmitter lever from the

feedback unit. The unit is factory adjusted and

need no further adjustment at installation than

described below.

Turn the helm to set the rudder tiller arm to

approximate centre position.

Set the mounting location to be in accordance

with the figure. The centre of the feedback

unit should be in line with the centre of the

rudder post. Mount the feedback unit to a

suitable platform using the screws provided. If

necessary, add blocking material under the

feedback unit to adjust the height of the

transmitter lever to be level with the rudder

tiller arm.

Due to space limitations, it may be necessary

to cut the length of the transmitter rod to

move the feedback unit closer to the rudder

post.

Rotate the feedback transmitter lever to

centre position. (Use the alignment mark to

line up the transmitter lever to be opposite the

cable entry into the feedback.)

Carefully observe the alignment marks. A

rudder feedback alarm may be the result if the

alignment instructions are neglected.

Note that the transmitter lever has two slots

for the transmitter link. The slots enable

maximum flexibility to provide the 1:1

mechanical linkage relationship. As a starting

point, set the transmitter rod to the inner limit

of the outer slot if possible. Drill and tap the

rudder tiller arm so that the Y1 dimension is

equal to the Y2 dimension (Use 4.2 mm drill

and 5 mm tap). Attach the ball joint to the

tiller arm, and connect the transmitter rod to

the ball joint at the rudder tiller arm.

Tighten the mounting screws for both the

feedback unit and the transmitter rod ball

joint.

Observe the feedback unit while someone

turns the helm wheel through the complete

rudder travel H.O. to H.O. and verify that the

mechanical linkage moves freely.

Page 2 of 2

ELECTRICAL CONNECTION

RF25 Rudder Feedback Unit

8-16V SimNet supply SimNet

T-joiner

SimNet backbone

SimNet drop cable

RF25 connection to SimNet

TECHNICAL SPECIFICATIONS

Dimensions:...................See figure

Weight:.........................0,5 kg (1,1 lbs)

Material: .......................Arnite T06 200 PBT

Environmental Protection: IP56

Safe distance to compass: 1,0 m (3,1 ft.)

Temperature range:

Operation:..............–25 to +55 °C

(–13 to +130 °F)

Storage:.................–30 to +70 °C

(–22 to + 158 °F)

Mounting: .....................Horizontal, vertical,

or upside down

Supply and interface: ......8-16V via SimNet

Power consumption:........0,4W

SimNet Network load factor (NL): 1

SimNet ports (input/output): 1

Cable supplied:...............5 m (16’) SimNet

cable with connector

Rudder angle: ................±120 degrees

Output signal: ................SimNet/NMEA2000

PGN127245

Accuracy: ......................±0.25° within ±5°,

otherwise ±0.5°

Repeatability:.................±0.1°

NMEA compliant

Transmitter link:.............Stainless 345 mm

(13.6") with 2 ball

joints.

Ball joint stud for rudder arm requires 4.2 mm

diameter hole and 5 mm tap.

SPARE PARTS

22014286 RF25 Rudder Feedback

w/accessories

20193454 Transmitter link

44133122 Transmitter rod

M5x325mm

20193624 Ball joint Ass'y (2)

RF25 Dimensions

Transmitter Link – dimensions

20222552 / A

Dieses Handbuch passt für folgende Modelle

Andere Simrad Schiffsausrüstung Handbücher

Simrad

Simrad ES70 - REV A Bedienungsanleitung

Simrad

Simrad ME70 - REV C Bedienungsanleitung

Simrad

Simrad ITI Bedienungsanleitung

Simrad

Simrad IS40 Bedienungsanleitung

Simrad

Simrad FS70 - REV 3 Bedienungsanleitung

Simrad

Simrad IS42J Bedienungsanleitung

Simrad

Simrad ES60 - DATASHEET REV A Bedienungsanleitung

Simrad

Simrad NSO evo3S MPU Bedienungsanleitung

Simrad

Simrad AP70 Bedienungsanleitung

Simrad

Simrad EK80 Bedienungsanleitung

Simrad

Simrad SimNet Kurzanleitung

Simrad

Simrad Maris ECDIS900 Bedienungsanleitung

Simrad

Simrad SX90 - DATASHEET FOR NAVAL AND COAST GUARD REV... Bedienungsanleitung

Simrad

Simrad EK15 Bedienungsanleitung

Simrad

Simrad BSM-3 Bedienungsanleitung

Simrad

Simrad EK80 Bedienungsanleitung

Simrad

Simrad IS80 Heading Repeater HR80 Bedienungsanleitung

Simrad

Simrad EK80 Bedienungsanleitung

Simrad

Simrad AP20 Bedienungsanleitung

Simrad

Simrad IS40 Bedienungsanleitung

Simrad

Simrad GO XSE Series Bedienungsanleitung

Simrad

Simrad GO XSE Series Bedienungsanleitung

Simrad

Simrad IS20 Combi Bedienungsanleitung

Simrad

Simrad NSS9 evo3S Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Clarion

Clarion GR10BT Reparaturanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch