Simu DMI5 Hz Bedienungsanleitung

DMI5Hz - DMI6Hz

Tubular operators with integrated radio and manual

override for blinds, awnings & roller shutters.

USA

S.A.S. au capital de 5 000 000 !- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090

5047058D

IMPORTANT - Review instruction

throughly before installing Hz motors

1/8

A4 x ØB / 90°

ØB

AØ min.

T min.

Ø 3/16

STEEL SAE5 or higher

Ø 1/4

For Compos

te Dr

For the Aluminum

Drive use the 5mm X

6mm screws supplied

with the drive

4 X

ASSEMBLY

- This device complies with part 15 of the FCC Rules. Operating is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

- Caution: Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

1.1 - TUBE PREPARATION

Warning: do not cut or drill the tube with the motor installed.

- Cut the tube to the required length.

- Remove all burrs from the tube.

- If using a round tube, cut a notch (D wide by C long) into one end of the tube.

- On round tubes measure length (A) and drill 4 holes around the tube. For octagonal

tubes 1 hole is sufcient (see dimension chart next page).

12 max. d2 > 8 inches min.

1 ft. < d1 < 65 ft.

d1 d2

WARNING

1 2

4 3

Nm ≥ 60 & ALUMINIUM DRIVE

DMI5 : 9910004

DMI6 : 9910062

For the aluminum drive Ais 20mm less than shown

26 4.2

BC D

75625-18 30-12 35-18 50-12

83660-14 80-14 100-14

71615-18

DMI5 Hz

120V / 60Hz

Ø / T min. = 47

DMI6 Hz

120V / 60Hz

Ø / T min. = 60

1.2 - INSTALLING THE TUBULAR MOTOR

1- Fit the adaptor over the crown. Align the slot in the adaptor with the raised key and rmly t the

adaptor over the crown. A crown adaptor is not necessary with 47mm (2") tubes.

2- Snap the drive wheel onto the drive shaft. Screw on the drive stop if needed (60 Nm+ operators).

3- Slide the tubular motor into the tube. Do not force or hammer on the head of the motor. If the

motor does not insert smoothly, remove the motor and le smooth the edge of the tube. On round

tubes conrm the raised key on the crown ts snugly into the cut slot on the end of the tube.

4- Secure the drive wheel to the tube. For the composite drive, use four 3/16" dia. steel pop rivets

or four 1/4" dia. screws with steel grade SAE 5 or higher. For the aluminum drive, use the three

5mm X 6mm cheese head screws provided.

1.3 - MOUNTING THE TUBULAR MOTOR

The DMI5Hz / DMI6Hz motor use standard T5 / T6 accessories.

- Mount the motor as shown using only SIMU accessories.

- Mount the motor heads at least 8" apart from each other to prevent RF interference.

- Always install the power cable with a drip loop to prevent water penetration.

- SIMU motors conform to IP44 requirements and as such must be protected against

direct weather elements such as rain, sleet, ...etc. Failure to do so could result in voiding

the warranty.

2/8

85 Nm max.

MOTOR

CABLE

POWER

120VAC

BLACK

WHITE

GREEN

HOT

NEUTRAL

GROUND

OPERATOR

WIRING CHART

3/8

10 Nm max.

(DMI 6 120 : 20Nm max.)

WIRING

2.1 - DMI Hz PERMANENT WIRING (shutter, shade or awning)

Warning: All wiring must conform to the National Electric Code and local codes.

- (1) The motor must be installed with a drip loop to prevent water intrusion.

- (2) Connect the motor to power using a listed junction box with appropriate cable strain reliefs.

- It is recomended a method of power disconnect for each motor be placed within sight of the motor to

cut power during servicing and facilitate reprogramming.

- Do not use the motor cable to penetrate building walls. Connect the motor to power in a listed junction

box and from the listed junction box run power in the manner proscribed by NEC. and local codes.

MOTOR

CABLE

POWER

120VAC

BLACK

WHITE

GREEN

HOT

NEUTRAL

GROUND

OPERATOR

WIRING CHART

Hand Held Transmitters Color Multi & Timer MultiWall switch Transmitter

Decoflex wall switch transmitterHz Timer

single channelfive channels

PROGRAM BUTTON

(back of transmitter)

PROGRAM BUTTON

(back of transmitter)

PROGRAM BUTTON

2.2 - DMI Hz PLUG-IN WIRING (shade or awning)

Warning: All wiring must conform to the National Electric Code and local codes.

- (1) The motor must be installed with a drip loop to prevent water intrusion.

- (2) If used outdoors, a GFCI receptacle with an outdoor cover is required.

- Do not use the motor cable to penetrate building walls.

The molded-on attachment plug can be removed when permanent installation is

required by National or Local Codes.

- Cut the exible cord at 10 mm from the start of the molded-on plug.

- Strip the cord jacket to required length in order to connect the motor to the Mains power

supply in a listed junction box according to National Electric Code and local codes.

- Strip the insulated insulation of the conductors and use the appropriate listed eld-wiring

wire nuts as per local and National codes in order to make the permanent wiring of the

operator.

COMPATIBLE TRANSMITTERS

4/8

>>>

>>> >>>

GO TO 4.3

3+ sec.

4.1 - WAKING UP THE MOTOR

Before programming, changing direction of rotation, setting the limits, etc…you

must wake the motor up. If using a multi-channel transmitter, conrm you are on

the desired channel. Press and hold the up and down together until the motor

gives a short up/down bounce. The motor is now awake.

4.3 - PROGRAMMING A TRANSMITTER CHANNEL TO A MOTOR

If using a multi-channel transmitter, conrm you are on the desired channel.

Press the Program Button and the motor will give a short up/down bounce.

Conrm the transmitter now controls the motor. A short push on the up of down

button should make the motor run until you stop it or the motor stop at its limits.

You should not have to hold the button down.

4.2 - DIRECTION OF ROTATION

You must check the direction of rotation before programming. If the direction

of rotation is not correct, press and hold the stop Button until the motor gives a

short up/down bounce. Conrm the direction of rotation is now correct.

PROGRAMMING

5/8

>>> >>> >>>

OFF

ON ON

5s.

>>>

4.4 - ADDING ADDITIONAL TRANSMITTERS (CHANNELS) TO THE MOTOR.

Use the transmitter that currently controls the motor and conrm it is on the correct channel.

Press and hold the Program Button until the motor gives a short up/down bounce. Conrm

transmitter is on the channel you wish to add and press the Program Button. The motor will

give a short up/down bounce. The new channel is now added. Repeat for any additionnal

transmitter channels you wish to add.

4.5 - DELETING A TRANSMITTER CHANNEL TO A MOTOR.

Use a transmitter that currently controls the motor and conrm it is on the correct channel

to control the motor. Press and hold the Program Button until the motor gives a short up/

down bounce. Press the Program Button of the second transmitter until the motor gives a

short up/down bounce. The second transmitter is now deleted.

4.6 - CLEARING THE MEMORY OF OLD TRANSMITTERS AND ADDING NEW TRANSMITTERS.

If all a motor transmitters are lost or damaged it is possible to clear the old memorized codes from

memory and add the new transmitter. Perform a double power cut in the following sequence:

1- Power off for at least 8 seconds

2- Power on for 8 seconds

3- Power off for at least 8 seconds

4- Power on. The motor will try and run for 5 seconds but will not run past its limits.

The motor is now in a temporary mode for 2 minutes. NOTE: this is not the "factory mode".

If a motor or motors are entered into temporary programing mode by mistake it can be cancelled

by pressing for a second on the UP, STOP or DOWN of any transmitter that motor has memorized.

The motor will also return to normal operating mode if left for 2 minutes.

5- Press and hold the Program Button of any unmemorized transmitter for more than 8 seconds.

When the motor gives a short up/down bounce release the button. The memory of the motor’s

receiver is now cleared of the old transmitters and the new transmitter has been added.

6/8

LIMIT ADJUSTMENT SCREWS ON OPPOSITE SIDE FROM MOTOR CABLE

5.1 - Identify which limit adjustment screw controls the up limit and which controls the

down limit (see above diagrams). It is important to note that the arrows by the

limits adjustments screws refer to the tube’s rotation. Thus if the material comes

off the tube on the back side and you are adjusting the limits from the side that the

motor cable is not on (as per diagram 2), the limit adjustment screw with the arrow

facing up controls the down limit and vice-versa.

5.2 - Turning an adjustment screw positive (+) will increase the maximum travel in the

direction that it controls and turning it negative (-) will decrease the maximum tra-

vel. For the adjustment screws on the side without the motor cable, turning counter

clockwise is positive (+) and clockwise is negative (-).

5.3 - To set a limit, run the motor in the selected direction.

5.4 - If the motor stops on its own before reaching the desired stop, turn the appropriate

limit screw positive (+). Every 2 or 3 turns of the limit adjustment screw will allow

the motor to travel about 1 inch further. After every few turns of the limit adjustment

screw use the control switch to move the motor to the new limit position. If the mo-

tor does not stop on its own before reaching the desired stop, go to step 5.6.

5.5 - When you are approximately at the desired stop, use the control switch to run the

motor away from the limit 2 or 3 feet and then back. This will allow you to see pre-

cisely where the limit is set. Make small adjustments and repeat.

5.6 - If the motor does not stop on its own at least 6 inches before the desired limit posi-

tion, stop the motor with the control switch. Then turn the adjustment screw in the

negative (-) direction. Conrm that the motor is stopped at the limit and set the limit

as in step 5.4 and 5.5. If the motor is not stopped at the limit, continue turning the

limit adjustment screw (up to 120 turns may be required).

NOTE: The motor has a built-in thermal cut-off. If after several minutes of use the motor

will not run in either direction allow the motor to cool approximately 20 minutes.

7/8

SETTING THE LIMITS

DOWN LIMIT ADJUSTMENT SCREW

MATERIAL ROLLS DOWN ON SAME SIDE AS LIMITS

UP ADJUSTMENT SCREW

MATERIAL ROLLS DOWN ON OPPOSITE SIDE AS LIMITS

UP LIMIT ADJUSTMENT SCREWDOWN LIMIT ADJUSTMENT SCREW

LIMIT ADJUSTMENT SCREWS ON SAME SIDE FROM MOTOR CABLE

6.1 - Identify which limit adjustment screw controls the up limit and which controls the

down limit (see above diagrams). It is important to note that the arrows by the

limits adjustments screws refer to the tube’s rotation. Thus if the material comes

off the tube on the back side and you are adjusting the limits from the side that the

motor cable is not on (as per diagram 4), the limit adjustment screw with the arrow

facing up controls the down limit and vice-versa.

6.2 - Turning an adjustment screw positive (+) will increase the maximum travel in the

direction that it controls and turning it negative (-) will decrease the maximum

travel. For the adjustment screws on the side with motor cable, turning counter

clockwise is negative (-) and clockwise is positive (+).

6.3 - To set a limit, run the motor in the selected direction.

6.4 - If the motor stops on its own before reaching the desired stop, turn the appropriate

limit screw positive (+). Every 2 or 3 turns of the limit adjustment screw will allow

the motor to travel about 1 inch further. After every few turns of the limit adjustment

screw use the control switch to move the motor to the new limit position. If the mo-

tor does not stop on its own before reaching the desired stop, go to step 6.6.

6.5 - When you are approximately at the desired stop, use the control switch to run the

motor away from the limit 2 or 3 feet and then back. This will allow you to see pre-

cisely where the limit is set. Make small adjustments and repeat.

6.6 - If the motor does not stop on its own at least 6 inches before the desired limit posi-

tion, stop the motor with the control switch. Then turn the adjustment screw in the

negative (-) direction. Conrm that the motor is stopped at the limit and set the limit

as in step 6.4 and 6.5. If the motor is not stopped at the limit, continue turning the

limit adjustment screw (up to 120 turns may be required).

NOTE: The motor has a built-in thermal cut-off. If after several minutes of use the motor

will not run in either direction allow the motor to cool approximately 20 minutes.

8/8

SETTING THE LIMITS

UP LIMIT ADJUSTMENT SCREW

MATERIAL ROLLS DOWN ON SAME SIDE AS LIMITS

DOWN LIMIT ADJUSTMENT SCREW

MATERIAL ROLLS DOWN ON OPPOSITE SIDE AS LIMITS

DOWN LIMIT ADJUSTMENT SCREWUP LIMIT ADJUSTMENT SCREW

MOTOR CABLE MOTOR CABLE MOTOR CABLEMOTOR CABLE

Andere Handbücher für DMI5 Hz

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Simu Steuereinheit Handbücher

Simu

Simu EOSUN Hz VS Bedienungsanleitung

Simu

Simu SIMUDRIVE SD100Hz Bedienungsanleitung

Simu

Simu veoHz Reparaturanleitung

Simu

Simu SIMUDRIVE SD100Hz Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung