SImx MANROSE FAN5875 Bedienungsanleitung

• The power cable of this product must withstand a minimum 10A

load.

•The main supply and interconnecting cables required for installation

of this unit are not included.

• This unit must be properly grounded.

• The disconnection of the product is acheived by incorporating a

switch in the fixed wiring in accordance with the wiring rules. The

heater must be isolated from the power by means of a disconnection

switch with a contact separation of at least 3mm.

• The appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to ensure that they do not play with

the appliance.

2. Ducting

Put one end of the 100mm diameter ducting into the vent hole and

connect to grille or cowl with one duct clip included. Seal space

around the grille using a suitable sealant. An eggcrate grille is includ-

ed in the package to be used if installed in soffit. If installed in wall a

weather proof cowl should be used (DCT0018).

INSTALLATION

A few minutes of planning can make a big difference to the installation

time and also to your satisfaction with the function of the unit.

1. Cutting a vent

Locate the exterior grille location on a wall or soffit, then cut a 105 mm

diameter hole to install grille/cowl.

Note: The length of duct is 3.0m. Make sure that from the centre of the

units installated position there must be a distance within 3.0m to the

outside vent.

3. Suitable location

The heater must be installed at least 2.1m above the floor.

The heater is most effective when you are standing directly beneath it,

Wall venting shown

wall

sealant ducting bathroom

heater

ceiling joist ceiling fascia

duct clip

Terminal

Blocks

4. Prepare the ceiling

Use this template to mark the hole

outline on the ceiling. Make sure a

distance between the edges and

wall is no less than 250mm. The

distance from the ceiling board to

the rooftop must be a minimum of

220mm.

5. Remove the fascia

Remove 4 screw covers at 4

corners of the fascia. Remove the

screws hidden behind. Remove

the fascia.

6. Wiring

Open the terminal block cover on

the housing and make connection

as the wiring diagram instructs,

then reposition the terminal block

cover.

INSTALLATION INSTRUCTIONS AND HOLE-CUTTING TEMPLATE

Read and save these instructions! Please use this card as hole cutting template 420mm×275mm.

EXHAUST

BLOWER

HEATER 1

HEATER 2

LIGHT

220V

-240V

M: Motor C: Capacitor : Thermal protector IN: Light lamp

MANROSE

PTC Heater Fan & Light

WARNING: Indicates that injury or death could occur if below

Warnings are not followed.

This unit must be installed to comply with the appropriate council

regulations and the Australia and New Zealand wiring rules

AS/NZS3000:2000 or lastest edition thereof.

All wiring must be carried out by a Licensed Electrician in accor-

dance with all applicable codes and standards.

Use this heater only as described in this manual. The manufacturer

does not recommend any other use as this may cause fire, electric

shock, or injury to persons. If you have questions, contact the manu-

facturer or local agent.

Make sure the power is off before the installation.

For the purpose of avoiding any dangerous gas leaking into your

bathroom, the duct vent of the heater must not be laid together with

the duct vent of air-fueled water heater or other open-fire appliances

into the same flue.

The heater is to be installed so that switches and other controls

cannot be touched by a person in the bath or shower.

This unit should not be installed directly above a shower or bathtub.

The unit must not be installed in a position where water may splash

onto the unit.

Dear customers

Please read all instructions before commencing installation.

CAUTION: Possibility of damage to equipment, installation or premis-

es if below Cautions are not followed.

• The appliance shall, under no circumstances, be covered with

insulating material or similar material.

•Regulations concerning the discharge of air have to be fulfilled.

• The unit must not be installed beneath a fixed socket.

• The unit is designed for installation in flat ceilings only. Do not mount

it on a sloping ceiling or a vertical wall.

• Before commencing any cutting, check in the ceiling space that

there are no obstructions such as electrical wiring, hidden utilities

or ceiling joists and that there is sufficient height clearance for the

unit. Check that the electrical wiring can be routed from the wall

switches to the mounting location.

• Joists, beams and rafters shall not be cut or notched to install the

appliance.

so generally the unit would be mounted in a place where you would stand

to dry yourself. For the exhaust fan to work efficiently, replacement air of a

volume equivalent to what is being extracted must be able to enter the

room. Generally, this air would be drawn under the door with a minimum

space of 20mm. If the room is airtight, the fan extraction will be reduced.

9. Replace the fascia

Reattach and screw the fascia onto the unit. Replace the plastic screw

covers.

Note: If it is necessary to run the wiring on the outside of the wall, use

a suitable conduit and fixings to properly locate and hold the wiring

used.

7. Fit one end of the duct to the fan outlet, and fix with duct clip.

Note: Keep the route as straight and tight as possible.

USE

Our bathroom heater uses a ceramic PTC element as a source of heat.

It also combines the functions of exhaust and light.

1. Power

‘POWER’ button On/Off

Switch on the ‘POWER’ button to operate the unit.

bathroom heater

spring clip

ceiling

ceiling joist

100

220mm

100mm minimum clearance

is required near all ceiling joists

8. Position the housing into the hole

Choosing the best direction to put the housing into the hole in

accordance with the position of the fan outlet. Pull in the installation

clips in the sliders before inserting the housing into the hole to avoid

damaging the plaster. Release clips in the sliders and use screws to

fasten the unit onto the ceiling.

Note: Try to keep the excess wire away from the housing.

This warranty does not cover damages or loss caused by:

1) Any consequential losses arising from incorrect installation or

operation or maintenance of this product.

2) Any consequential losses arising from incorrect wiring of this prod-

uct.

3) Any modifications or changes made to the unit, other than those

recommended by the Manufacturer.

WARRANTY

The unit is warranted against defects in manufacturing and

workmanship for a period of 5 years. The warranty does not extend

installation of the unit or any associated wiring or any damage

caused by installation or wiring.

The installation must be conducted by a licensed electrician and a

suitable certificate of safety is to be issued by the electrician who

installed the unit. Warranty claims will be voided unless a certificate

of safety can be produced when required, prior to service or repair.

MAINTENANCE

Clean

1) Shut off the power before cleaning.

2) Wipe the fascia with care using a soft damp cloth.

3) Allow to dry thoroughly before switching on.

Note: Ensure the unit is cool enough to touch before handling.

Note: Do not switch on/off frequently when in use. Shut off the power

if in long vacancy.

3. Exhaust

‘FAN/HEATER 1’ button

This switch will extract air from the room. When in the FAN position

there is no heating of the room.

2. Lighting

‘LIGHT’ button On/Off

This switch controls the light.

4. Heating

‘FAN/HEATER 1’ button

When this switch is in the “HEATER 1”position, the heater unit will be

activated.

When the “HEATER 1” is turned on, half heating is applied to the room.

When the “HEATER 2” is also turned on, full heating is applied to the

room. When operating the heater there is no extraction.

MAIN TECHNICAL PARAMETERS

LIST OF PARTS

Operation unit

Installation instruction & hole-cutting template

1 piece

Alluminum ducting 3.0m 1 piece

Duct clip

Switch 1 piece

2 piece

Egg-crate external grille 1 set

Model Number

Rated Voltage

Rated Frequency

Rated Power

220V-240V

50Hz

2250W

Please use this card as hole cutting template 420mm×275mm.

Read and save these instructions!

INSTALLATION INSTRUCTIONS AND HOLE-CUTTING TEMPLATE

We reserve the rights to revise these instructions without any prior notice.

For warranty purposes fill out the following details and save with proof of purchase.

This information must be submitted in the unlikely event that this product fails.*

MODEL NO.: FAN5875

Purchased from:

Date of purchase:

*All warranty claims must be submitted through [email protected]

FAN5875

Andere SImx Heizung Handbücher

SImx

SImx Manrose FAN5876 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung