Singer SIWM7000 Bedienungsanleitung
USER MANUAL
Fully Automatic Washing Machine
MODEL :SIWM7000
If this appliance is supplied with a cord extension set or and electrical
portable outlet device, the cord extension set or electrical portable
device must be positioned so that it is not subject to splashing or ingress
or moisture.
The appliance is not intended for use by young children or infirm
persons without supervision.
Young children should be supervised to ensure that they do not play with
the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
The power supply cord must be unplugged after use.
Please use low foaming laundry detergent.
CAUTION:
1. SAFETY WARNING
2. PARTS IDENTIFICATION
3. ACCESSORIES
4. CONTROL PANEL
5. SPECIFICATIONS
6. INSTALLATION
7. DETERGENT CONTAINER
8. OPERATION
9. PROGRAMS
10. MAINTENANCE
11. TROUBLE SHOOTING
12. ELECTRICAL G DIAGRAM
1
2
2
3
3
4
8
9
11
12
13
14
CONTENTS
-1-
SAFETY WARNING
Never use water above
50℃.
Do not let children play
with the machine.
Do not put the cord to unplug
from powerpoint.
Do not put hands into the
rotating tub.
70 C
Do not clean the body of the
washer with volatile solvent
such as petrol and methane.
Also, do not pour these
solvents into the tub for
washing or drying purposes.
0.5
0.8 0.2
Make sure the lid is closed
especially during spin.
Don ' t s w itc h o n t h e
p o w e r i f t h e w a t e r
pressure is lower than
0.05M Pa and h ig her
than 0.5MPa.
WARNING! WARNING!
NOTE!
WARNING!
WARNING!
NOTE!
NOTE! NOTE!
Never use the plug as
shown.
The highest point of the drain
hose must be in the height of
0.7m~1.2m above floor level.
K e e p t h e w a s h i n g
machine away from fire or
heat source.
Do not place the washing
machine in a damp place
and do not pour water onto
the control panel.
Do not expose washing
m a c h i n e t o d i r e c t
sunlight or rain.
PARTS IDENTIFICATION
ACCESSORIES
Level adjustment knob
(Please turn off the
tab after using)
Inlet hose
Lint filter
Pulsator
Power cord
Drain hose
(Put into the drain or
tub during operation)
Adjustable foot
Inner tub
Control panel
Base
Detergent box
Fabric softener dispenser
Noise and mice-proof plate
(It is inserted into the base
to reduce noise and keep
the mice away.)
-2-
2PC 1PC
(2set screws)
Inlet hose Noise and mice-
proof plate
UP
Special tool
1PC
45
1 2 3
6
2
Water temperature selector
1
4
Water level button
Press this button to select water level.
5
Press this button to select water
temperature.
Process button
Press this button to select the process
you need.
Start/hold button
Press this button to start/pause the
washing machine.
Power button
Press this button to turn on/off the
washing machine. Do not turn on the
washing machine again until 3 minutes
later after it is turned off. The washing
machine will turn off automatically
when the program is finished, and it
will turn off automatically if you do not
press the start button to start the
machine within 10 minutes after press
the power button to turn on the
machine.
3
SPECIFICATIONS
Rated voltage Rated frequency
Rated input power
Rated water volume
(high water level )
230~240V 50Hz
480W 70L
Net weight
7.0kg
569mmX583mmX957mm
38kg
Rated wash and spin
capacity
Dimension
Water pressure 0.05MPa-0.5MPa
957mm
583mm
569mm
-3-
CONTROL PANEL
-4-
INSTALLATION
Place the washing machine on a firm and level surface, use the level
adjustment knob to regulate the adjustable foot until the washing machine is
stable.
1. Take out the noise-proof plate. 2. The entrance is in the front
of the base.
3. Insert the noise-proof plate
into the base.
Insert the noise-proof plate into the washing machine base
Place the washing machine
at least 5cm away from the
wall.
Alternation of adjustable foot
In order to prevent vibration during
operation, you can loosen the level
adjustment knob and regulate the
adjustable foot until the washing
machine is stable, and then tighten
it. (The inclination angle of the
washing machine should not be
more than 2 degrees.)
5cm
Loosen Tighten
4. Lay down the washing
machine, fasten the two
screws.
-5-
INSTALLATION
Water Temperature
Cold :
Recommended cold water temperature is 10~23.8℃.
Hot :
Recommended hot water temperature is 50~60℃.
Warm:
Mixture of hot and cold water. (Warm water temperature is dependent upon the water
temperature and the pressure of both the hot and cold water supply lines.)
IMPORTANT:
Owner should turn off water supply whenever there will be an extended period of non-use.
Water Pressure
Do not operate the washer when the water pressure is lower than 0.05MPa or higher than
0.5MPa to avoid damage of the inlet system.
Water supply requirements
Change the direction of the drain hose
Unfasten the fixed screw of
the drain hose joint.
Lead out the drain hose from
the opening to the other side.
Fasten up the screw to fix
the drain hose.
Connection of the drain hose
0.7m~1.2m
Insert the end of the drain hose into the hook shelf,
and hang the drain hose over a drain outlet (bath tub,
sink, etc.).
Note: The highest point of the drain hose must be in
the height of 0.7m~1.2m above floor level,
otherwise, the washer can not work normally.
Connection of the drain hose
-6-
INSTALLATION
Connection of the inlet hose
Faucet:
Installation and connection of the Inlet hose
The faucet must be with G3/4" standard screw thread. If not , it is
impossible to connect the inlet hose properly.
NOTE: water supply faucets should be readily accessible to
permit turning them off when washer is not being used.
NOTE: Refer to Section on Water Supply Requirements before connecting
water inlet hoses.
A: If you just have one water supply line (cold or hot water), connect the
inlet hose to the cold water connector in water mixing valve. (Do not
unscrew the lid of hot water connector in water mixing valve, otherwise it
will result in water leakage from the hot water valve during fill cycles.
IMPORTANT: In this situation you can not set wash temperature to WARM
OR HOT.
1. Connect the water inlet hose to the
connector by turning the connecting
nut.
2. Then connect the other end of water inlet
hoses to the cold connector in water
mixing valve by turning the connecting
nut.
To prevent water leakage, please ensure the connecting nut is tightened
securely.
Use special tool (enclosed with the packaging) to tighten the connecting
nut by screwing clock-wise, until the hose connector does not rotate at
joint of the connecting nut.
RUBBER RING
SEAL
CONNECTING
NUT
Be sure a rubber ring is inside the
connecting nut.
WATER
INLET HOSE CONNECTING NUT
SPECIAL TOOL
COLD WATER
CONNECTOR
LID OF HOT WATER
CONNECTOR
HOSE
CONNECTOR
Note:
The washing machine is to be connected to the water mains using new
hose-sets supplied with the appliance, old hose-sets should not be re-
used.
Inhaltsverzeichnis
Andere Singer Waschmaschine Handbücher
