SINGTRONICS SE-48SP Bedienungsanleitung

igtronics

…when it counts!

Model SE-48SP

Headset Instructions

The SE-48SP series headset is adjusted at the factory for immediate use. The

headset is equipped with a single plug and a coiled cord.

The headband is adjustable through a full range of motion, and the locking nuts

may be tightened to allow you to custom t the headphone. Place the headphone

over your head and adjust the slides up until minimum pressure is felt on the top

of your head. For maximum noise attenuation, the clamping pressure of the head-

band has been set at the factory. Releasing the clamping pressure by bending the

headband is not advised, because loss of attenuation will result.

The microphone boom is fully adjustable and will rotate 180 degrees for use on

the left or right side of the head.

Make sure you are speaking into the side of the mic labeled “Talk” or substantial

loss of gain will occur. Microphone placement should be at the corner of the

mouth, approximately ¼” from the lips.

Your SE-48SP headset has a push to talk switch located on the mic side ear cup.

The mic is operative only when the switch is depressed. For intercom and radio

function, depress the switch to talk.

When you rst connect the headset, turn the volume control on the headset up

to the full clockwise position, then adjust the listening volume with the audio

control of either your radio or intercom as appropriate. If applicable, crew mem-

bers should also turn their individual headset volumes up fully. Doing this allows

for a full range of adjustment for each passenger, since those with the most acute

hearing can turn their headset volume down, if necessary.

continued on back…

The headset parts may be cleaned with mild soap and water using a soft cloth.

Then dry immediately. Caution: Do Not immerse any part of the headset in water

or any other liquid. Be especially careful not to allow the microphone to become

wet! Exposure to moisture may cause internal corrosion and failure and will void

your manufacturers warranty.

Cleaning will help the headset maintain its “like new” condition for many years.

WINDSCREEN

The microphone windscreen will reduce annoying wind noise and breath pops

picked up by headset microphones. It also protects the microphone element

from dirt and moisture. The windscreen should be washed regularly to maintain

hygiene and avoid clogging. Wash in warm water and mild soap. Rinse thoroughly

and make sure it is completely dry before putting it back on.

To remove the windscreen, carefully grasp the windscreen lightly along its entire

length and remove from the microphone element being careful not to twist the

element itself.

Put the windscreen on the microphone by gently pulling from the open end. Do

not pull it so tightly that it stretches against the end of the microphone.

WARRANTY

Your headset is covered by a limited two-year parts and labor warranty. Please see

the enclosed warranty card for details.

You may refer to the parts list on the reverse side, if you choose to replace parts

yourself. The parts list describes parts for this particular headset only. Parts lists

for other models are available on our Web Site or can be obtained by contacting

Sigtronics Corporation.

Sigtronics Corporation

178 East Arrow Highway

San Dimas, CA 91773

Phone: 909 305-9399

E-mail: info@sigtronics.com

Web Site: www.sigtronics.com













































 



























SIGTRONICS SE-48SP HEADSET PARTS IDENTIFICATION BREAKDOWN

ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION ITEM P/N DESCRIPTION

1100221 WIRE, #22, 19 STRAND, 4 INCH 13 800197 HEADBAND , WITH CUSHION, SE-48 25 100393 CLIP, ANTI-ROTATION, YOKE, PLASTIC

2100063 KNOB, 3/8 INCH, BLACK 14 100603 YOKE, EAR CUP MOUNT, METAL, BLACK 26 100602 HEADBAND, METAL, STANDARD, BLACK

3100077 POTENTIOMETER 15 100568 STRAIN RELIEF, CABLE 27 100604 BRACKET, YOKE SUPPORT WITH TANG, BLACK

4100858 RECEIVER AND MOUNT, 300 OHM, MONO 16 100369 EAR SEAL, FOAM FILLED 28 100232 SWITCH, SPDT, MOMENTARY

5100108 SCREW, 4-40 X 1/4, THREAD FORMING 17 800192 PREAMP 29 100625 O-RING, PTT, HEADSET

6800193 MICROPHONE & FLEX BOOM ASSEMBLY 18 800035 CABLE, HEADSET, STEREO, COILED 30 100428 SWITCHGUARD, PTT, BLACK

7100251 E-RING, EAR CUP TO YOKE RETAINER 19 100373 SLIDE, YOKE BRACKET, LONG, NYLON 31 10 0317 BUTTON, SWITCH, PTT, RED

8100252 NUT, HEX, 8-32, LOCKING 20 100374 FOAM, SOUND ATTENUATING. NOTCHED, 1/2 INCH 32 90 0111 WINDSCREEN, MICROPHONE, FOAM, PACKAGED

9100401 EAR CUP, PRINTED AND DRILLED, MIC & NON MIC SIDE 21 100376 FOAM, SOUND ATTENUATING. RECEIVER HOLE, 1/2 INCH 33 10 0 611 WINDSCREEN, MICROPHONE, FOAM, BULK

10 100597 NUT, HEX, 3/8-24, FLEX BOOM ADAPTER 22 100379 FOAM, SOUND ATTENUATING, RECEIVER COVER, 1/4 INCH 34 100612 O-RING, WINDSCREEN RETAINER, SE-48

11 100363 SCREW, 8-32 X 1/2, PHILLIPS HEAD 23 100684 FOAM, SOUND ATTENUATING, FOR SLOTTED EAR CUP ONLY 35 100613 OPTIONAL – HEADBAND, METAL, LARGE, BLACK