TECHNICAL SPECIFICATIONS
CONNECT YOUR SMART PLUG TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
Initiate the connectivity session
by pressing the RF button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide
for the latter.
Operating voltage: AC 120 V 60 Hz
Maximum load: 120V - 15A
Resistive: 1800 W
Incandescent: 960 W
Electronic ballast: 500 VA
Motor: 0.5 HP
Operation temp.: 0 °C to 40 °C (32 °F to 104 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Certifications:
Conforms to UL 60730-1 / CSA E60730-1
Indoor installation only
Zigbee HA 1.2 profile
Frequency: 2.4 GHz
Transmission power: +8 dBm
Connect all your
compatible Zigbee devices
the same way, by going to
the next closest device.
3
When your smart plug is
connected, close the connectivity
session of your GT130 gateway or
your compatible Zigbee gateway.
4
Connect the smart plug to your network
by pressing the ON / OFF button
for 5 seconds.
The connection status light
Blinks green: The smart plug is connecting
Green for 5 seconds: Connected
Note: If the smart plug cannot reach the
gateway’s network after 20 seconds, try to
connect it again.
2
1
Hub
2nd
1st
3rd
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of
their products against defects in material and workmanship
for a 3-year period from the date of purchase, under
normal use and service, when proof of purchase of such
is provided to the manufacturer. This warranty does not
cover any transportation costs that may be incurred by the
consumer. Nor does it cover a product that has been
improperly installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the
terms of this warranty, will be to supply a new unit and this
releases the manufacturer from paying the installation costs
or other secondary charges linked to replacing the unit or
the components.
For more information, visit our Website:
660-2520-0001-E
Neviweb® is a registered trademark of Sinopé Technologies Inc. in
Canada and the United States.
Apple and the Apple logo are trademarks of Apple Inc., registered in
the U.S. and other countries. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries. Google Play and the Google
Play logo are trademarks of Google Inc.
Transmitter module IC: 3653A-EM3585 / FCC ID: NHS-EM3585
This device complies with Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device does not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help.
• Avoid using in an environment with high humidity
or extreme temperatures.
• Do not expose the device or its accessories to
flammable liquids, gases, or other explosives.
• Controllable devices should never be used to
supply power to or control the ON / OFF status
of medical and/or life support equipment.
WARNING: Failure to follow these safety instructions
can result in fire, electric shock, other personal
injuries, or damage to the smart plug and other
property. Read all the safety instructions below
before using the smart plug.
Reset: Press and hold the ON / OFF
button for 5 seconds.
(The indicator will remain on
for 5 seconds.)
