Sioux Tools 1449HPG Bedienungsanleitung

NOTE: Parts are no longer available for this tool.

The manual will continue on the next page.

Form No. A1041C

Date 12-91

AIR SUPPLY

The efficiency and life of this tool depend on the proper supply of clean, dry, lubricated air at

about 90 lbs. P.S.I., although higher or lower pressures may be used. The use of an air line

filter, pressure regulator and lubricator is recommended.

Before connecting the tool, blow the air line to remove water and dirt which may have accumu-

lated. This is especially important for a new line or when the line has not been used for some

time.

HOSE AND HOSE CONNECTION

The air supply hose is 3/8" I.D. If extension hose is necessary, use 1/2" hose, with couplings

not less than 3/8" I.D.

LUBRICATION

An oil supply to the air motor is important. SIOUX air line lubricators are recommended. Adjust

to deliver 2 drops of SIOUX Air Motor Oil No. 288 per minute. When air line lubricator is not

used, place 10-15 drops of SIOUX No. 288 oil into the air inlet twice daily.

OPERATION

This tool is equipped with a teasing throttle. By slightly depressing the trigger the chuck will

rotate slowly. This is useful for starting a drill bit without first spotting with a punch. By fully

depressing the trigger the chuck will rotate at it’s top speed.

If the gear case is removed or loosened, retighten to 35 ft. lb.

INSTRUCTIONS & PARTS LIST

FOR 1449HPG DRILL

(SERIAL C)

24 63359 Ass’y—Trigger

25 11600 Body—Valve

26 54222 Valve

28 54968 Retainer—Exhaust

29 54955 Adaptor—Inlet

30 30463 Screen

31 21541 Ring—Retainer

32 14281 Ring—“O”

33 14366 Ring—“O”

34 63545 Ass’y—Silencer

35 10203 Bearing—Ball(3)*

36 25439 Washer(4)*

37 30062 Pin(4)*

38 19317 Ass’y—Gear&Bearing(2)*

39 22716 Carrier—Gear

40 19317 Ass’y—Gear&Bearing(2)*

41 22703 Carrier—Gear

42 10228 Bearing—Ball

43 10040 Bearing—Needle(4)*

ITEMSNOTSHOWN

63359 NamePlate

09953 Screw—Drive(2x3/16)(2)*

Fig- Part

ure No. Name

Fig- Part

ure No. Name

PARTS LIST FOR 1449HPG

3/8" DRILL NON-REV

350 R.P.M.

(SERIAL C)

1 21133 Chuck(1/16"—3/8"Cap)

2 64003 Case—Gear

3 30375 Fitting—Grease

4 63390 Ass’y—PlanetaryReduction

5 19266 Gear—Ring

6 21510 Ring—Retainer

7 63553 Ass’y—PlanetaryReduction

8 10220 Bearing—Ball

9 13550 EndPlate—Front

10 14342 Ring—“O”

11 64057 Cylinder

12 54860 Rotor—6Tooth

13 63192 Ass’y—RotorVane(Setof5)

14 10552 EndPlate—Rear

15 10230 Bearing—Ball

16 21491 Ring—Retainer

17 12660 Housing(IncludesName Plate)

18 40157 Pin—Dowel(1/8"X11/8")

19 14378 Ring—“O”(2)*

20 06459 Screw—Set(#8-32X3/16")

21 12676 Trigger

22 06458 Screw—Set(#8-32X3/16")

23 21401 Spring

*OrderQuantityAs Needed

4Printed in U.S.A.

1. KEEP WORK AREA CLEAN: Cluttered areas and benches invite accidents.

2. AVOID DANGEROUS ENVIRONMENT: Keep work area well lit.

3. KEEP CHILDREN AWAY: All visitors should be kept safe distance form work area.

4. STORE IDLE TOOLS: When not in use, tools should be stored in dry, high or

locked-up place—out of reach of children.

5. DON’T FORCE TOOL: It will work best and safest at the designed rate.

6. USE RIGHT TOOL: Don’t force small tool to do the job of a heavy-duty tool.

7. WEAR PROPER APPAREL: No loose clothing or jewelry to get caught in

moving parts.

8. USE SAFETY GLASSES: Use safety glasses with most tools. Also face or dust

mask if it is a cutting operation.

9. SECURE WORK: Use clamps or vise to hold work. It’s safer than using your

hand and it allows freedom of both hands to hold tool.

10. DON’T OVERREACH: Keep proper footing and balance at all times.

11. MAINTAIN TOOLS WITH CARE: Keep tools sharp and clean for best and

safest performance. Follow instructions for lubricating and changing accessories.

12. DISCONNECT TOOLS: When not in use; before servicing; when changing

accessories such as blades, bits, cutter, etc.

13. REMOVE ADJUSTING KEYS AND WRENCHES: Form habit of checking to see that

keys and adjusting wrenches are removed form tool before turning it on.

14. CAUTION: The use of an accessory with this tool not provided or specified by

SIOUX TOOLS may be hazardous.

GENERALSAFETYPRECAUTIONS

FOR AIR TOOLS

This pdf incorporates the following model numbers:

1449HPG

Inhaltsverzeichnis

Andere Sioux Tools Bohren Handbücher

Sioux Tools

Sioux Tools 1453ES Datenblatt

Sioux Tools

Sioux Tools Force Series Bedienungsanleitung

Sioux Tools

Sioux Tools 8800ES Betriebsanleitung

Sioux Tools

Sioux Tools SDR4P Series Bedienungsanleitung

Sioux Tools

Sioux Tools 9000 Installations- und Betriebshandbuch

Sioux Tools

Sioux Tools 9440 Bedienungsanleitung

Sioux Tools

Sioux Tools 8800ES Betriebsanleitung

Sioux Tools

Sioux Tools SDR5P Series Bedienungsanleitung

Sioux Tools

Sioux Tools 8800ES Bedienungsanleitung

Sioux Tools

Sioux Tools SDR10P Bedienungsanleitung

Sioux Tools

Sioux Tools A Series Bedienungsanleitung

Sioux Tools

Sioux Tools 1410B Bedienungsanleitung

Sioux Tools

Sioux Tools 1464 Bedienungsanleitung

Sioux Tools

Sioux Tools 1449ESR Datenblatt

Sioux Tools

Sioux Tools 2S Series Bedienungsanleitung

Sioux Tools

Sioux Tools 8000ES Bedienungsanleitung

Sioux Tools

Sioux Tools 5434KL Technische Daten

Sioux Tools

Sioux Tools 1AM Series Bedienungsanleitung

Sioux Tools

Sioux Tools 5203 Bedienungsanleitung

Sioux Tools

Sioux Tools 1556 Bedienungsanleitung

Sioux Tools

Sioux Tools 1457ES Datenblatt

Sioux Tools

Sioux Tools SDR10S Bedienungsanleitung

Sioux Tools

Sioux Tools VAC-FORCE 1557 Bedienungsanleitung

Sioux Tools

Sioux Tools SDR10T40N3 Bedienungsanleitung

Beliebte Bohren Handbücher anderer Marken

Makita

Makita BDF456 Bedienungsanleitung

Black & Decker

Black & Decker LDX220 Bedienungsanleitung

Hitachi

Hitachi DH 40MA Bedienungsanleitung

Challenge

Challenge JO Technisches Referenzhandbuch

Makita

Makita LXFD01 Bedienungsanleitung

Festool

Festool T18+3 Bedienungsanleitung

Milwaukee

Milwaukee M12 FPDX-202X Bedienungsanleitung

EINHELL

EINHELL TE-RH 32 E Bedienungsanleitung

Makita

Makita DHP484 Bedienungsanleitung

Makita

Makita FD05 Bedienungsanleitung

Bosch

Bosch PSB 530 RA Bedienungsanleitung

Maximum

Maximum 054-1359-4 Bedienungsanleitung

Makita

Makita HP332D Bedienungsanleitung

Raider

Raider RDP-HD31H Bedienungsanleitung

Bort

Bort BPM-1400x2 Bedienungsanleitung

Black & Decker

Black & Decker 7266 Bedienungsanleitung

KENT USA

KENT USA TRD1230 Bedienungsanleitung

Bosch

Bosch GSB 19-2 RE Bedienungsanleitung