SIRE XROOM Technisches Datenblatt

OPERATING AND INSTALLATION MANUAL

RECOVERY AND HEATING UNIT

XROOM

Version 1 – GBR(23/06/2021) D-502-0152

TABLE OF CONTENTS

1. General information .................................................................................................................................................................. 5

1.1. Introduction........................................................................................................................................................ 5

1.2. Warnings and Symbols ........................................................................................................................................................................... 5

1.3.1. Unit Designation ..................................................................................................................................................................................... 6

1.3.2. Prohibited environment, use, installation of Xroom: ............................................................................................................................ 6

1.4. Transport, Delivery Control, and Storage ..............................................................................................................7

1.4.1. Transport ................................................................................................................................................................................................ 7

Version 1 – GBR(23/06/2021) D-502-0152

1.4.2.

1.4.3.

Delivery Inspection................................................................................................................................................................................. 7

Storage.................................................................................................................................................................................................... 7

1.5. Contents of the Package ......................................................................................................................................7

1.5.1. Xroom 100 (XR1-010-EC…)...................................................................................................................................................................... 7

1.5.2. Xroom 250 (XR1-025-EC…)...................................................................................................................................................................... 8

1.6. Before Commencing the Installation ............................................................................................................................... 8

2. Technical Parameters................................................................................................................................................................. 9

2.1.

2.1.1.

Design of the Xroom unit.................................................................................................................................................. 9

Front metal cover (position 1) .............................................................................................................................................................. 11

2.1.2. Installation template (position 2) .........................................................................................................................................................11

2.1.3.

2.1.4.

2.1.5.

2.1.6.

2.1.7.

2.1.8.

Mounting pins (position 3) ................................................................................................................................................................... 11

Unit body –fitting (position 4) ............................................................................................................................................................. 11

Unit cover (position 5) .......................................................................................................................................................................... 11

Reinforcement (position 6) ...................................................................................................................................................................11

Bolt M6x30 (position 7) ........................................................................................................................................................................ 11

Filters (position 8) ................................................................................................................................................................................. 12

2.1.9. Filter caps (position 9)........................................................................................................................................................................... 12

2.1.10. Preheating (position 10) ....................................................................................................................................................................... 12

2.1.11. Fans (position 11).................................................................................................................................................................................. 12

2.1.12.

2.1.13.

2.1.14.

2.1.15.

2.1.16.

2.1.17.

2.1.18.

Recuperator (position 12) ..................................................................................................................................................................... 12

Electric heat exchanger (position 13) ................................................................................................................................................... 12

Controller (position 14)......................................................................................................................................................................... 12

Regulator box (position 15) .................................................................................................................................................................. 12

FILTER RESET button (position 16)........................................................................................................................................................ 12

Limit switch (position 17)...................................................................................................................................................................... 12

Main switch (position 18) ..................................................................................................................................................................... 12

2.1.19. Supply cable (position 19)..................................................................................................................................................................... 12

2.1.20. Water exchanger (position 20) ............................................................................................................................................................. 12

2.1.21.

2.1.22.

Bleed valve (position 21) ...................................................................................................................................................................... 12

Flexible hoses for connection to the heating system (position 22) ..................................................................................................... 12

2.2. Main dimensions of the Xroom unit ...................................................................................................................13

2.2.1. Xroom-100 (XR1-010-EC...) .................................................................................................................................................................. 13

2.2.2. Xroom-250 (XR1-025-EC…).................................................................................................................................................................... 13

2.3. Technical parameters of Xroom units ............................................................................................................................ 14

2.3.1.

2.3.2.

Basic technical parameters ........................................................................................................................................ 14

Acoustic Data........................................................................................................................................................................................ 15

2.3.3.

Version 1 – GBR(23/06/2021) D-502-0152

Technical data of water heaters........................................................................................................................................................... 16

2.3.4. Heat and moisture recovery efficiency ................................................................................................................................................ 17

3. Unit Installation ....................................................................................................................................................................... 18

3.1.

3.1.1.

3.1.2.

General information, recommendations, and safety when installing the Xroom units............................................... 18

Electrical safety before installation of the unit.................................................................................................................................... 18

Unpacking ............................................................................................................................................................................................. 18

3.1.2.1.

3.1.2.2.

3.1.3.

Unpacking the Xroom Unit –Box 1 ...................................................................................................................................................... 18

Unpacking Installation –Box 2 ............................................................................................................................................................. 20

Unit Location ........................................................................................................................................................................................ 21

3.1.3.1. Location During the Building Reconstruction ...................................................................................................................................... 21

3.1.3.2.

3.1.3.3.

3.1.4.

3.1.5.

Location and operation of the unit in the area with a furnace (fire place) ......................................................................................... 21

Unit Location and Operation in the Area with an Air Conditioning Unit ............................................................................................ 21

Minimum Installation Distances .......................................................................................................................................................... 21

Installation Positions of the Xroom Unit.............................................................................................................................................. 22

3.2. Xroom Unit Installation ..................................................................................................................................... 22

3.2.1. Installation Components Required for Installation of the Xroom Unit ............................................................................................... 22

3.2.2. Fitting and Mounting the Installation Template with Mounting Pins................................................................................................. 23

3.2.2.1.

3.2.2.2.

Fitting the installation template on the wall when using the construction module........................................................................... 23

Fitting the Installation Template on the Existing Wall ........................................................................................................................ 23

3.2.2.3. Installation Template Mounting .......................................................................................................................................................... 23

3.2.3. Preparation of Piping Holes in the Existing Wall.................................................................................................................................. 24

3.2.4. Preparation of Supply and Drain Piping ...............................................................................................................................................25

3.2.4.1. Extension of piping for walls with a thickness greater than 500 mm.................................................................................................. 26

3.2.4.1.1. Extension of the Supply Piping with a Damper Assembly ................................................................................................................... 26

3.2.4.1.2. Drain piping extension –white plastic tubes....................................................................................................................................... 26

3.2.5. Installation of the Supply and Drainage Piping on the unit................................................................................................................. 27

3.2.6. Gluing Insulating Pads .......................................................................................................................................................................... 28

3.2.7. Installation of the Xroom unit on the wall........................................................................................................................................... 29

3.2.8. Xroom Unit Final Fitting ....................................................................................................................................................................... 29

3.2.8.1. Electric heater variant (XR1-010-ECE1...), without heating –cold (XR1-010-ECS0...) ......................................................................... 29

3.2.8.2. Water heater variant (XR1-xxx-ECV1...)............................................................................................................................................... 30

3.2.9. Securing, Insulating Piping in the Wall................................................................................................................................................. 31

3.2.10.

3.2.11.

Fitting the Piping on the Outer Side of the Wall with Outlet .............................................................................................................. 32

Installation of the Front Metal Cover................................................................................................................................................... 32

3.3. Electrical Installation –Connection to Mains ...................................................................................................... 33

3.3.1. General Information –Safety ............................................................................................................................................................... 33

3.3.2. Connection to Mains ............................................................................................................................................................................ 33

3.3.2.1.

3.3.2.2.

3.3.2.3.

3.3.3.

Connection of the Unit to the Wiring Box............................................................................................................................................ 34

Connecting the Unit to the Electrical Outlet ........................................................................................................................................ 34

Recommended Xroom Unit Protection................................................................................................................................................ 34

Display of electrical parameters........................................................................................................................................................... 34

4. Regulation ................................................................................................................................................................................ 35

4.1.

4.2.

4.2.1.

General Information –Safety ......................................................................................................................................... 35

Electrical Accessories to the Xroom Unit ....................................................................................................................... 35

Connecting Electrical Accessories ..............................................................................................................................35

4.2.2.

Version 1 – GBR(23/06/2021) D-502-0152

Radon Sensor Connection –AQS RADON ......................................................................................................................................................... 36

4.2.2.1.

4.2.2.2.

Technical Parameters of the Sensor for Connection to the Unit...................................................................................................................... 36

Functionality of the unit after connecting the radon sensor ........................................................................................................................... 36

4.2.3. External Contact Connection –EXT 1................................................................................................................................................................ 36

4.2.3.1. Technical Parameters of External Contact........................................................................................................................................................ 37

4.2.3.2.

4.3.

Functionality of the Unit when Controlled by External Contact EXT1 ............................................................................................................. 37

Wiring Block Diagram ....................................................................................................................................................................................... 37

5. Commissioning ......................................................................................................................................................................... 38

5.1.

5.2.

5.3.

5.3.1.

Prior to first startup, check:............................................................................................................................................38

Activation –Basic UnitCommissioning .......................................................................................................................... 38

Controller Operating Modes .......................................................................................................................................... 38

Sleep Mode –Regular Operating Mode ........................................................................................................................................................... 38

5.3.2.

5.3.3.

Control Mode –1 click ...................................................................................................................................................................................... 39

Unit Setting Mode –2 clicks.............................................................................................................................................................................. 39

5.4. Unit Control ......................................................................................................................................................39

5.4.1. Control panel –controllers ............................................................................................................................................................................... 39

5.4.2.

5.4.3.

5.4.4.

Description of the functions of the buttons and regulation........................................................................................................................... 40

Description of the ventilation power setting range ......................................................................................................................................... 41

Ventilation Power Settings ............................................................................................................................................................................... 41

5.4.5. Temperature Setting Range –only in the electric version (XR1-xxx-ECE1...).................................................................................................. 41

5.4.6.

5.4.7.

5.4.8.

Setting the Required Temperature:.................................................................................................................................................................. 41

Display of the Indicated Statuses on the Controller by LEDs ........................................................................................................................... 41

Hidden Regulation Functions............................................................................................................................................................................ 42

5.4.9. Automatic Unit Control using AQS Sensors...................................................................................................................................................... 42

6. Replacing Filters ....................................................................................................................................................................... 43

6.1.

6.2.

6.3.

Removal of a filter .......................................................................................................................................................... 43

Filter Inserting ................................................................................................................................................................. 44

Reset filter countdown ................................................................................................................................................... 44

7. Regular Maintenance and Cleaning of Xroom Units............................................................................................................... 45

7.1.

7.1.1.

7.1.2.

Visual Inspection of the Unit Casing ................................................................................................................................................................. 45

Visual Inspection and Cleaning of the Heat Exchanger .................................................................................................................................... 45

Visual Inspection of the Supply Cable .............................................................................................................................................................. 46

7.2. Inspection –cleaning of the inner area of the unit –disassembly......................................................................... 46

7.2.1. Cleaning the Fan Chamber and Fans................................................................................................................................................................. 46

7.2.2. Visual Inspection –Cleaning of Preheating, if fitted with the unit (XR1-xxx-ECxxxxP...)................................................................................... 47

7.2.3. Visual Inspection –Cleaning of Inlet and Drainage Piping ............................................................................................................................... 47

7.2.4. Visual Inspection and Cleaning of the Heat Recovery Exchanger .................................................................................................................... 48

7.2.5. Re-installation of Internal Components into the Unit...................................................................................................................................... 48

8. Servicing ................................................................................................................................................................................... 49

8.1.

8.2.

Error Messages –Troubleshooting Procedure............................................................................................................... 49

Failure persists ................................................................................................................................................................ 50

9. Final Decommissioning, Dismantling, and Disposal................................................................................................................ 50

10. Warranty ............................................................................................................................................................................. 50

11. In Conclusion ....................................................................................................................................................................... 51

pac

1. General information

1. Introduction

-This document “Operating and Installation Manual” is intended for decentralised Xroom recovery units

(hereinafter referred to as the “Unit”) with apossible combination of water or electrical heating –2in1.

At the same time, it is superior to the brief manual placed directly on the unit, the so-called “Quick

Manual”.

-Installation and connection of the unit may only be performed by atrained person with the appropriate

authorisation for the connection of electrical equipment who has the appropriate tools and resources

at his disposal.All the instructions and recommendations provided in this manual must be observed

during installation.

-Detailed familiarisation with this document is important for the unit's correct and safe installation and

functioning. Failure to comply with the conditions set out in this document may lead to the unit's

malfunction.

-Please, retain this unit installation manual for future reference after reading it thoroughly.

-It is forbidden to interfere in any way with the unit's internal connection other than as specified in this

manual. Due to the continuous development of our products, we reserve the right to change this manual

without prior notice.

-Children and persons with reduced physical, sensory, or mental capabilities, or lack of experience and

knowledge, may use the unit only under supervision or if they were instructed on the unit's use in asafe

way and understand potential risks.

1. Warnings and Symbols

-The following names and symbols shall be used in the operating manual, on the packaging, and on the

product for particularly important information:

Warning, pay attention to all the risk alerts and warnings, as well as preventive measure instructions.

Danger, observe all the warnings; there is a risk of electric shock or a situation, which can result in death

or serious injury, if not prevented.

Reference to other manual sections

Read the operating manual.

Protective conductor connection

Notification of the correct position when handling and storing the packaging.

Notification of the need for protection against moisture.The product –packaging marked with this

symbol must not be transported on open vehicles and stored in roofless buildings and on the ground

without apad.

Notification of the content –product’s fragility and the need for careful handling of the packaged

product.

Notification of the need for protection against moisture and of the fragility of the product inside the

kaging.

Version 1 – GBR(23/06/2021) D-502-0152

Caution –never cover the unit.This symbol on the unit indicates that any material covering the unit can

cause afire.

Caution very hot surface.

Caution -portions of this product may become hot and cause burns.Pay particular attention to the presence of

children and vulnerable people.

3. Use of the Xroom unit

1. Unit Designation

- The Xroom is an air-conditioning unit using ventilation technology with recovery of heat (countercurrent

recovery exchanger) and humidity (enthalpy exchanger) with the possibility of independent space heating

at the unit’s installation site (depending on the selected unit type).By default, the unit is equipped with

aCO2air quality sensor (alternatively also with an RH humidity sensor), which allows it to ventilate only

when needed.The user shall set only the unit's output (flow rate, temperature –based on the selected

type) according to the place of use (how many people will be in the room) and the unit will ventilate and

heat as per the actual needs.

-The unit can be used in spaces with the maximum nominal flow requirement:

o100 m3/h – Xroom 100 –regular residential premises, smaller offices, hotel rooms, etc.

o250 m3/h – Xroom 250 –larger office facilities, school classrooms, hospital rooms, etc.

-The unit is designed for horizontal installation on the perimeter wall, which provides simple access to the

outside environment (fresh air).

-You can install the unit in the wall with the minimum thickness of 180 mm.

-The unit is intended for continuous operation with the possibility of using the manual operation mode

(ventilates continuously) or the automatic operation mode (ventilates as needed –required by the air

quality sensors –AQS).

-The unit can be used not only for controlled ventilation, but also for space with heating requirements

(ventilation and heating are independent of each other). In case of type configuration with:

oElectric heating, theunit is equipped with advanced regulation with temperature sensor for the

given area (installation site).Using an integrated temperature sensor, the user can choose the

appropriate temperature degree that meets his requirements,

oWater heating, the unit is equipped with awater exchanger, which is connected to the standard

heating system using an external G 3/4" thread and is controlled using an independent fitting –

thermostatic valve and head (not included in the supply).The unit control is equipped with a

temperature sensor that detects hot water in the exchanger and starts the heating function.The

function of the water heater depends on the function of the boiler –heating system.

-The unit also allows for the antifreeze temperature function (tempering the heated space to prevent

freezing).In the electric version, settings are on the controller, and in the water version, they are on the

thermal head (snowflake symbol).

-The unitis intended for indoor covered and dry areas with aroom temperature of +5 °C to +30 °C and the

maximum relative humidity of 70%, non-condensing.

-The temperature of supplied fresh air from the outside may be between -20 °C and +40 °C (applies to

the version with preheating).If the temperature of the supplied air is lower than -20 °C, the unit may

be switched off automatically in order to protect it from possible damage.

1.3.2. Prohibited environment, use, installation of Xroom:

-Exhausting burning or glowing substances!

-Exhausting readily flammable or explosive gases,

-Exhausting aggressive media,

-Exhausting liquids of any kind,

-In an environment with an increased incidence or risk of explosion, flammable substances, and

increased dust and/or air containing other harmful impurities,

Version 1 – GBR(23/06/2021) D-502-0152

-In an environment with higher condensation humidity, such as: bathrooms, swimming pools, saunas,

etc.,

-The unit must not be installed just below the electrical socket or wiring box,

-The unit must not be installed in aposition that could affect its proper functioning, or near the curtains

or other flammable materials.

-Neither the manufacturer nor the supplier is liable for damage caused by improper use of the units. The

user bears the risk.

4. Transport, Delivery Control, and Storage

1. Transport

-During transport, keep the product in the position indicated by the symbol on the packaging.

-The packaging must not be loaded with a weight higher than that permitted by the manufacturer.

-The packaging must not be exposed to ambient effects.

-The transport air temperature must range between -25 to 55 °C,

-The transport relative humidity must range between 10 % and 90 %non-condensing.

-Use adequate tools to prevent damage to the goods and damage to the health and safety of persons.

-In the case of further transport without original packaging or with changed original packaging, it must be

ensured that the equipment is optimally secured and protected against damage.

1.4.2. Delivery Inspection

-Before starting the installation and before unpacking the unit from the box, it is necessary to check for

any traces of damage on the packaging.If the packaging is damaged, write arecord of the damage and

contact your carrier, please.

-Check if you have received the product actually ordered by you.After unpacking, check that the unit and

other components are in order.Please, report any discrepancy with the order to the supplier

immediately.

If an order complaint is not made immediately after delivery, it will not be considered later.

1.4.3. Storage

-If you do not plan to install the unit immediately after purchase, it must be stored in an indoor, non-

condensing environment at temperatures ranging between +5 to +40 °C. If the product is transported at

temperatures below 0 °C, it must be put into the working environment where it will be installed for at

least 2hours after unpacking.

1.5. Contents of the Package

1.5.1. Xroom 100 (XR1-010-EC…)

Box 1 – Xroom unit

Version 1 – GBR(23/06/2021) D-502-0152

-Xroom unit body with front metal cover

-installation template with assembly pins

1pc

-bolt M6x25 5pc

-bolt M6x20 with a plastic head 2pc

-Quick manual + safety data sheet 1pc

-serial plate 1pc

Box 2 –mandatory installation accessories XR1-01-DUCT-1 (for installation into a wall with thickness of the

max. 500 mm)

-plastic white tube Ø125 mm, length 500 mm 1pc

-supply line assembly with damper Ø125 mm, length 500 mm 1pc

-plastic square outlet with damper 1pc

-plastic square outlet without damper 1pc

-self-tapping bolt Ø4x22 4pc

-insulation washer 170x170x5 with hole Ø127 mm 2pc

1.5.2. Xroom 250 (XR1-025-EC…)

Box 1 –Xroom unit

-Xroom unit body with front metal cover

-installation template with mounting pins

1pc

-bolt M6x25 5pc

-bolt M6x20 with a plastic head 3pc

-Quick manual + safety data sheet 1pc

-serial plate 1pc

Box 2 –mandatory installation accessories XR1-025-DUCT-1 (for installation into a wall with thickness of the

max. 500 mm)

-plastic white tube Ø150 mm, length 500 mm 1pc

-supply line assembly with damper Ø150 mm, length 500 mm 1pc

-plastic square outlet with damper 1pc

-plastic square outlet without damper 1pc

-Self tapping bolt Ø4x22 4pc

-insulation washer 210x200x5 with hole Ø153 mm 2pc

6. Before Commencing the Installation

-Before commencing the installation, we recommend that you attach the serial plate (by default, supplied

with the package) to the operating documentation (e.g.: equipment operating book, etc.), which is

subsequently kept for alater maintenance records and servicing.

-Check that there are no electrical or other lines (e.g. gas, water, etc.) at the point of installation of the

unit on the wall that could be damaged during installation.

-Make sure that the installation of the unit does not endanger the building’s statics and meets all the

legislative safety requirements.

-Select how you will drain the condensate:

oUsing supply piping through afacade outlet –standard solution.

oUsing a condensation piece –it is not part of the delivery, must be provided by the customer.

-If condensate is drained through the facade outlet, check that there would be no damage to the

construction or contact with live equipment.

Version 1 – GBR(23/06/2021) D-502-0152

2. Technical Parameters

1. Design of the Xroom unit

Fig. 1

Version 1 – GBR(23/06/2021) D-502-0152

Fig. 2

16 17

Version 1 – GBR(23/06/2021) D-502-0152

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIRE Heizsystem Handbücher

SIRE

SIRE OXeN X2-W-1.2-V Leitfaden

Beliebte Heizsystem Handbücher anderer Marken

aerauliqa

aerauliqa QR350ABP Bedienungsanleitung

WatchGas

WatchGas ATEX BEACON Bedienungsanleitung

Viessmann

Viessmann Vitoligno 300-H Betriebsanleitung

Lampoassa

Lampoassa 203GT Bedienungsanleitung

MSA

MSA SOA-1022 Bedienungsanleitung

nilan

nilan Compact P Bedienungsanleitung

ITR

ITR OASIS NE-S Bedienungsanleitung

Carrier

Carrier 48LJD Abmessungen und Installationsanleitung

aldes

aldes EVEREST XV Bedienungsanleitung

Kober

Kober C22SPV23MEF Bedienungsanleitung

Oxygen

Oxygen X-Air V400 Bedienungsanleitung

Carrier

Carrier FB4CNF Bedienungsanleitung

Kroll

Kroll HM200 Handbuch

Kroll

Kroll HM200 Handbuch

NuAire

NuAire XBOXER XBC Series Bedienungsanleitung

Trane

Trane VR104GD-U Series Bedienungsanleitung

Vents

Vents VUT V mini Bedienungsanleitung

Viessmann

Viessmann Divicon Bedienungsanleitung