Sitten BT850A Bedienungs- und Wartungshandbuch

80MM THERMAL RECEIPT

PRINTER

PROGRAMMER MANUAL

Format Description :

The programming manual command description includes the following sections:

1）[Name]

This is the first part of the command descriptions. ASCII code is given command of the form

and the function overview of command .

2）[Format]

This section uses the ASCII coding form, Hex code form, Decimal code form of three kinds of

formal description of the command. Which part of the range compared to a decimal number no

special instructions, such as in the following example 1 ≤ n ≤ 4, where 1 is a decimal number,

rather than the ASCII code table in "1".

3）[Range]Gives the allowable ranges for the arguments.

4）[Description]Describes the command’s function.

5）[Detail]

The command notice is given. Because commands in different modes, when with different

commands, will lead to mutual influence, and this section gives the details.

6）[Reference]Gives the lists of related commands.

---> ESC SP n :Transmit real-time status

---> [Format] ASCII: ESC SP n

Hex: 1B 20 n

Decimal: 27 32 n

---> [Range] 0 ≤ n≤255

---> [Description] Transmitted in real time specified by the parameter “n” Printer Status：

---> [Detail] •Immediatelyreturns the printer associated status after receiving the command.

---> [Reference]

[Name] Horizontal tab

[Format]ASCII HT

Hex 09

Decimal 09

[Decription] Moves the print position to the next horizontal tab position.

[Details]

•This command is ignored unless the next horizontal tab position has been set.

• If the next horizontal tab position exceeds the printing area,

the printer setstheprinting position to [Printing area width + 1].

• Horizontal tab positions are set with ESC D.

• If this command is received when the printing position is at [printing area width

+ 1], the printer executes print buffer-full printing of the current line and

horizontal tab processing from the beginning of the next line.

[Reference]ESCD

LF [Name] Print and line feed

[Format] ASCII LF

Hex 0A

Decimal 10

[Description] Prints the data in the print buffer and feeds one line based on the current linespacing.

[Note] This command sets the print position to the beginning of the line.

[Reference] ESC2，ESC3

DLEDC4nmt

[Name] Real-time pulse generator

[Format] ASCII DLE

DC4

Hex 10 14 n m t

Decimal 16 20 n m t

[Range] n=1,m=0,1

≤

≤8

[Decription] Output pulse is specified by the parameter t connection pins, “m” show as below：

Connect Pins

Cash Drawer Connect Pin 2

Cash Drawer Connect Pin 5

Pulse high time for[t*100 ms]，low time for [t*100

ms]

。

[Details]• When the printer is executing a command to open the cash drawer (ESCp or DELDC4),

the command is ignored.

• In serial mode, the printer immediately after receiving the order.

• In parallel mode, the printer is busy when the command is not executed.

• If the print data same as the command contains data, the data will be used as the command

is executed. The user must take into account this situation.

• Don’t try to insert the command in two or more bytes in the command sequence.

• Even if the printer is set to disabled by the command of ESC = (select peripheral), the

order is still valid.

[Reference] ESCp

ESCSPn

[Name] Setting the right side character spacing

[Format] ASCIIESC SP n

Hex1B 20 n

Decimal 27 32 n

[Range] 0≤n≤255

[Description]Setting the right side character spacing for [n¬0.125 mm].

[Note]• For the double-width mode, the right side character spacing is double than the normal

mode. When the character is magnified , the right side character spacing is n times

than the normalmode.

•This command does not affect the setting of Hanzi characters.

• The command to set the value of independent standard mode in each mode.

[Defaults] n=0

ESC!n

[Name]

Select print

mode(s)

[Format]

SCIIESC

Hex 1B 21 n

Decimal

27 33 n

[Range]0≤ n≤ 255

[Description]Selects print mode(s) ,using n as follows:

Bit

OFF/ON

Hex

Decimal

Functions

OFF

00 0

Character font

(12

24)

。

01 1Character fontB

17)

。

1---

N/A

2---

N/A

OFF

00 0

Emphasized mode not selected.

08 8

Emphasized mode selected.

OFF

00 0

Double-height mode not selected.

10 16

Double-height mode selected.

OFF

00 0

Double-width mode not selected.

20 32

Double-width mode selected.

6---

N/A

OFF

00 0

Underline mode not selected.

80 128

Underline mode selected.

[Note]• When both double-height and double-width modes are selected,

quadruple sizecharacters are printed.

• The printer can underline all characters, but can not underline the space set by

HT or 90° clockwise rotated characters.

•

The thickness of the underline is that selected by ESC , regardless of the

character size.

• When some characters in a line are double or more height, all the characters

on the line are aligned at the baseline.

• ESC E can also turn on or off emphasized mode. However, the setting of the

last received command is effective.

• ESC —can also turn on or off underline mode. However, the setting of the last

received command is effective

•GS ! can also select character size. However, the setting of the last received

command is effective.

• Emphasized mode is effective for alphanumeric and Hanzi. All print modes

except emphasized mode is effective only for alphanumeric.

[Defaults] n=0

[Reference] ESC-,ESCE,GS !

ESC$nLnH

[Name] Set absolute print position

[Format] ASCIIESC $ nL nH

Hex1B 24 nL nH

Decimal27 36 nL nH

[Range]0≤ nL≤ 255

0≤ nH

≤

255

[Description]Sets the distance from the beginning of the line to the position at

whichsubsequent characters are to be printed.

•

The distance from the beginning of the line to the print position is

[( nL + nH * 256) *(vertical or horizontal motion unit)] inches.

[Note] • Settings outside the specified printable area are ignored.

• In standard mode, the horizontal motion unit ( x) is used.

[Reference] ESC\, GS $, GS \

ESC%n

[Name]Select/cancel user-defined character set

[Format] ASCIIESC % n

Hex 1B 25 n

Decimal 27 37 n

[Range] 0≤ n≤ 255

[Description]Selects or cancels the user-defined character set.

• When the LSB of n is 0, the user-defined character set is canceled.

•When the LSB of n is 1, the user-defined character set is selected.

[Note]When the user-defined character set is canceled,the internal character set is

automatically selected

• n is available only for the least significant bit.

[Defaults] n=0

[Reference] ESC&,ESC?

ESC&yc1c2[x1d1...d(y×x1)].. .[xkd1...d(y×xk)]

[Name] Define user-defined characters

[Format] ASCII ESC & y c1 c2[x1d1...d(y  x1)]...[xkd1...d(y

  xk)]

Hex 1B 26 yc1 c2[x1d1...d(y  x1)]...[xkd1...d(y

  xk)]

Decimal 27 38 yc1

c2[x1d1...d(y

 

x1)]...[xk

d1...d(y

  xk)]

[Range] y=3

32 ≤ c1≤ c2≤ 126

0≤ x≤ 12(12×24)

0≤ x≤ 9(9×17)

0≤ d1...d(y× xk)≤ 255

[Description]Defines user-definedcharacters.

•y specifies the number of bytes in the vertical direction.

• c1 specifies the beginning character code for the definition, and c2 specifies the

final code

• x specifies the number of dots in the horizontal direction.

[Note]• The allowable character code range is from ASCII code <20>H to <7E>H (95characters).

•

It is possible to define multiple characters for consecutive character codes.

If only one character is desired, use c1 = c2.

• d is the dot data for the characters. The dot pattern is in the horizontal directionfrom the

left side. Any remaining dots on the right side are blank.

• The data to define a user-defined character is(y×x)bytes.

• Set a corresponding bit to 1 to print a dot or 0 to not print a dot.

•

This command can define different user-defined character patterns by each

fonts. To select a font, use ESC !

• A user-defined character and a downloaded bit image cannot be defined

simultaneously. When this command is executed, the downloaded bit image is

cleared.

• The user-defined character definition is cleared when:：

1) ESC @ is executed.

2) ESC ? is executed.

3) ESC? is executed

4) The printer is reset or the power is turned off.

• When the user-defined characters are defined in font B (9 ╳17),only the

mostsignificant bit of the 3rd byte of data in vertical direction is effective.

[Defaults] The internal character set

[Reference] ESC%,ESC?

[Example]

•

When font A

(12*24)is selected.

•

When font B

17)

is selected.

d1=<0F>Hd4=<30>Hd7=<40>H...

d2=<03>Hd5=<80>Hd8=<40>H...

=<00>Hd6=<00>Hd9=<20>H...

d1=<1F>Hd4= <08>Hd7=<10>H...

d2=<FF>Hd5= <08>Hd8=<04>H...

d3=<80>Hd6=<00>Hd9 =<00>H...

ESC*mnLnHd1...dk

[Name] Select bit-image mode

[Format]ASCIIESC

∗

d1...dk

Hex

2A m nL nH d1...dk

Decima l

42 m nL nH d1...dk

[Range]m=0, 1, 32,33

0≤ nL≤ 255

0≤nH≤ 3

0≤ d≤ 255

[Description]Selects a bit-image mode using m for the number of dots specified by nL and nH,as follows:

Mode

Vertical Direction

Horizontal Direction

Number of

Dots

DotDensity

Number of Data(K)

08-dot single-density 867.7dpi 101.6dpi nL +nH

∗

256

18-dot double-density 867.7dpi 203.2dpi nL +nH

∗

256

32 24-dot single-density 24 203.2dpi 101.6dpi (nL+

∗

256)

∗

33 24-dot double-density 24 203.2dpi 203.2dpi

(

+nH

∗

256)

∗

dpi:Print dots per 25.4 mm (1inch)

[Note]

•

If the values of m is out of the specified range, nL and data following are processed

as normal data.

nL and nH represents the horizontal upper figure points, calculated by nL + nH256 points.

•If the bit-image data input exceeds the number of dots to be printed on a line,the

excess data is ignored.

•d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0to

not print a dot.

•If the width of the printing area set by GS L and GS W less than the widthrequired

by the data sent with the ESC * command, the following will beperformed on the line

in question (but the printing cannot exceed the maximumprintable area):

①The width of the printing area is extended to the right to accommodate theamount

of data.

②If step ①does not provide sufficient width for the data, the left margin isreduced

to accommodate the data.For each bit in the single density mode (m = 0, 32) of the

data, the printer prints two points: For double density mode (m = 1,33) of each bit of

data, the printer prints a dot . When calculating the amount of data that can be printed

on one line, they must be considered.

• After printing a bit image, the printer returns to normal data processing mode.

• This command is not affected by print modes (emphasized, double-

strike,underline, character size or white/black reverse printing), except upside-

downprinting mode.

•The relationship between the image data and the dots to be printed is as

follows:

• When 8-dot bit image is selected:

•When 24-dot bit image is selected:

ESC- n

[Name]

Turn underline

mode on/off

[Format]

ASCII ESC

Hex 1B 2D

Decimal 27 45

[Range]0≤ n≤ 2,48≤ n≤ 50

[Description]Turns underline mode on or off, based on the following values of n:

Function

0, 48

Turns off underline mode

1, 49

Turns on underline mode (1-dot thick)

2, 50

Turns on underline mode (2-dots thick)

[Note]• The printer can underline all characters (including right-side character spacing),

but cannot underline the space set by HT.

•The printer cannot underline 90° clockwise rotated characters and

white/blackinverted characters.

• When underline mode id turned off bysetting the value of n to 0 or 48,

thefollowing data is not underlined, and the underline thickness set before

themode is turned off does not change. The default underline thickness is

1 dot.

•Changing the character size does not affect the current underline thickness.

• Underline mode can also be turned on or off by using ESC !. Note,

however,that the last received command is effective.

[Defaults] n=0

[Reference] ESC!

Inhaltsverzeichnis

Andere Sitten Drucker Handbücher

Sitten

Sitten FTP-80C Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung