SIZZIX 660425 Bedienungsanleitung

Instruction Booklet

Table of Contents

Safety Instructions

1. Introduction

2. Machine Placement

3. Setting Up the Big Shot Pro Machine

Inserting the Sliding Tray and Adapter Pad

Attaching the Crank Handle

4. Operating Instructions

Using Bigz Pro, Bigz XL, Bigz or Originals with Crease Rule

Using AllStar, Bigz, Originals or On The Edge Dies

without Crease Rule

Using Framelits or Wafer-Thin Dies

Using Sizzlits, Clearlits or DecoEtch Dies

Using Embossing Folders, Embosslits or

DecoEmboss Dies

Using Textured Impressions Pro Embossing Folders

Using Texturz Texture Plates

Using Ellison SureCut, ClearCrop or Ellison Custom Dies

5. Helps & Hints

6. Maintenance

Cleaning Your Machine

Keeping Dies Clean

Recognizing Worn Plastic Slides

Replacing Plastic Slides

7. Troubleshooting Solutions

8. Materials Guide

9. Die and Accessory Compatibility Table

10. Warranties

11. Instructions in Other Languages

French

German

Spanish

For additional help, call Sizzix within USA 866-742-4447 or

outside USA 949-598-5897 or within UK 0871 222 2277 or

outside UK +44 (0) 845 345 2277 or visit

Sizzix.com.

WARNING

When using this product, basic precautions should always be

followed, including, but not limited to, the following:

• Alwaysplaceandoperatethismachineonaclean,flat,sturdy,non-skid

surface (stout table or workbench). Do not allow any part of the machine to

overhang the edges of your work area.

• Toreducetheriskofpersonalinjury,closesupervisionisnecessarywhenthe

Big Shot Pro is used near children.

• Notrecommendedforusebychildrenunder14years.

• Useonlyattachmentsandaccessoriesrecommendedbythemanufacturerof

your Big Shot Pro die-cutting machine.

• Donotuseoutdoors.

• Pinchhazard.Keephands,fingersandclothingawayfromcontactwithrollers.

• Donotoverloadthemachine.SeeMaterialsGuide(page13)andneverusemore

than three pieces of thinner materials and one piece of thicker materials.

• Cuttinghazard.Donotcontactthebladeofthedies.

• UseonlySlidingTraysuppliedwithyourBigShotProdie-cuttingmachine.Using

another type or brand could cause damage to your machine and dies.

• CarryyourBigShotProdie-cuttingmachineusingthemoldedhandholdsat

both ends of the machine. Lifting or carrying the machine by any other part

of the machine is unsafe.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Store in one of the well spaces under the Sliding Tray.

Read and understand all the instructions before

using your Big Shot Pro Machine.

The Sizzix®Big Shot™Pro Machine package includes all tools and parts necessary

for full assembly and operation. The Big Shot Pro Machine will cut and emboss a

wide variety of materials with the entire line of Ellison, AllStar and Sizzix dies and

embossing tools. See the Materials Guide (page 13) for specifics. When not in use,

place the dies in Sizzix and Ellison Storage Solutions (sold separately).

1. Introduction

Lift the Big Shot Pro Machine by its molded handholds at the ends of the Machine.

Place the machine on a clean, flat, sturdy, non-skid surface at a height and

positionthatarecomfortablefortheuser.Nopartofthemachineshouldhang

over the edge of the work surface.

2. Machine Placement

3. Setting Up the Big Shot Pro Machine

Parts included:

Item: Qty:

(1) Crank Handle 1

(2) Lock Washer 1

(3) Screw 1

(4) Screw Cap Cover 1

(5) Sliding Tray 1

(6) Cutting Pad 1

(7) Adapter Pad 1

(8) Premium Crease Pad 1

(9) Mylar Shims (0.1mm) 2

Tools required:

3mm Allen Wrench (Included)

Die Pick (Included)

(1 ) Crank Handle

Die Pick

(2) Lock Washer (3) Screw (4) Screw Cap Cover

(7) Adapter Pad

14 1/4" x 12 1/4" x 3/16"

(36.20cm x 31.12cm x 0.50cm)

(8) Premium Crease Pad

14 1/4" x 12 1/4" x 1/8"

(36.20cm x 31.12cm x 0.32cm)

(9) Mylar Shims

0.1mm x 2

3mm Allen Wrench

(6) Cutting Pad

14 1/4" x 12 1/4" x 1/8"

(36.20cm x 31.12cm x 0.32cm)

(5) Sliding Tray

15 5/8" x 12 7/8" x 5/8"

(39.69cm x 32.70cm x 1.59cm)

Inserting the Sliding Tray and Adapter Pad

1. Remove Big Shot Pro machine from the shipping carton and place it on a

clean, flat, sturdy, non-skid surface. Take care when lifting machine out of the

carton, as it weighs 30 lbs (13.6 kg).

2. Remove Sliding Tray from bottom of the carton. Place Sliding Tray onto Side

Rails. For cutting with Sizzix dies, place Adapter Pad in Sliding Tray.

3. The Sliding Tray can now move back and forth through the machine.

Attaching the Crank Handle

1. Slip the Lock Washer (Item 2) over the Screw (Item 3) and drop them into the

hole in the top of the Crank Handle (Item 1).

2. Push the Crank Handle assembly over the square roller shaft protruding

from the Big Shot Pro Machine. Insert Allen Wrench into Screw (Item 3) to

tighten. Turn clockwise (Figure A). Tighten Screw as far as possible to ensure

maximum pressure.

3. Press the Screw Cap Cover (Item 4) in place.

WARNING The Big Shot Pro Machine is very heavy.

Use extreme care and caution when handling.

Seek assistance whenever possible.

Figure A

(1) Crank Handle

(3) Screw

(2) Lock Washer

Square Roller Shaft

(4) Screw Cap Cover

Molded Handholds

Using all Sizzix Bigz™Pro, Bigz XL, Bigz or Originals™Dies with

Crease Rule*

1. Place a die on a Cutting Pad with foam side up. Place paper or desired material

to be cut on top of the die. Place the Premium Crease Pad on top of the paper

or material to create a “sandwich” (Figure B). (Extended Cutting Pad and

Extended Crease Pad [both sold separately] may also be used with XL-sized

dies.) A Mylar Shim may be necessary; see Troubleshooting Solutions on page 12.

2. Place sandwich on top of the Adapter Pad in the Sliding Tray.

3. Push Sliding Tray into the opening of the Big Shot Pro Machine. Keep hands

away from roller and dies while in use.

4. NotetherotationoftheCrankHandleandcontinuetorotateitinthesame

direction until the sandwich has passed through the opening of the rollers.

Dies can be passed through the rollers in either direction, from the right or

from the left.

5. Remove the sandwich from the Big Shot Pro. Your die-cut shapes are ready

to use!

*A Crease-Rule Die is similar to a regular Bigz (steel rule) Die; however, it contains

both cutting (sharp) rule and crease (blunt) rule.

4. Operating Instructions

WARNING Pinch and cutting hazard. Keep hands, fingers

and clothing away from contact with rollers

and dies while in use.

Figure B

See Die and Accessory Compatibilty Table on page 14

Paper

Die

"Sandwich"

Sliding Tray

Adapter Pad Cutting Pad

Premium Crease Pad

Mylar Shim

Using any size AllStar®Dies or Sizzix Bigz, On The Edge™or

Originals Dies without Crease Rule

1. Place a die onto an appropriately sized Cutting Pad or the Premium Crease Pad.

Place paper or desired material to be cut on top of the die. Place another

appropriately sized Cutting Pad on top of the paper or material to create a

“sandwich” (Figure C).

2. Place sandwich on top of the Adapter Pad in the Sliding Tray.

3. Follow Steps 3–5 in Operating Instructions, page 6.

Figure C

Paper

Die

Premium Crease Pad

or Cutting Pad

Cutting Pad

"Sandwich"

Sliding Tray

Adapter Pad

Using Framelits™ or Wafter-Thin Dies

1. Place material to be cut on top of a Cutting Pad. Align die on top of material as

desired. Place Cutting Pad on top of die to create a “sandwich” (Figure D).

2. Place sandwich on Big Shot™ Pro Solo Platform, Solo Shim and Solo Thin-Die

Adapter (sold separately) and place on top of the Adapter Pad in the Sliding

Tray.

3. Follow Steps 3–5 in Operating Instructions, page 6.

Figure D

Paper

Die

Cutting Pad

"Sandwich"

Sliding Tray

Adapter Pad

Solo Platform

Solo Shim

Solo Thin-

Die Adapter

Using Embossing Folders, Embosslits™or DecoEmboss™Dies

1. With Simple Impressions Embossing Folder, Textured Impressions Embossing

Folder or Embosslits or DecoEmboss Die open, insert paper, foil or other

embossable material, then close like a book. Place Standard Cutting Pads above

and below the closed Folder to create a “sandwich.”

2. Place sandwich on Big Shot Pro Solo Platform and Solo Shim (sold separately)

(Figure F) and place on top of the Adapter Pad in the Sliding Tray.

3. Follow Steps 3–5 in Operating Instructions, page 6.

Using Sizzix Sizzlits®, Clearlits™or DecoEtch™Dies

1. Place a Sizzlits Die onto a Standard Cutting Pad with foam side up. Place paper

over the die. Place another Standard Cutting Pad over the paper or material to

create a “sandwich.” For a Clearlits Die, place die over photo or other material so

that the area to be cut shows through the die. Then place photo or material

and die between Standard Cutting Pads to make sandwich.

2. Place sandwich on Big Shot Pro Solo Platform and Solo Shim (sold separately)

and place on top of the Adapter Pad in the Sliding Tray (Figure E).

3. Follow Steps 3–5 in Operating Instructions, page 6.

Figure E

Figure F

Textured Impressions

Embossing Folder

Standard Cutting Pad

Paper

Die

Cutting Pad

"Sandwich"

Sliding Tray

Adapter Pad

Solo Platform

Solo Shim

Cutting Pad

Paper

Textured Impressions

Embossing Folder Solo Platform

Solo Shim

Using Texturz™Texture Plates

1. Place a Texture Plate on the Big Shot Pro Solo Platform and Solo Shim

(sold separately) with the desired design facing up. Place paper or desired

material on top of the Texture Plate. Place Silicone Rubber on top of paper.

Place Impressions Pad on top of Silicone Rubber to create a “sandwich”

(Figure H).

2. Place sandwich on top of the Adapter Pad in the Sliding Tray.

3. Follow Steps 3–5 in Operating Instructions, page 6.

Figure H

Silicone Rubber

Paper

Impressions Pad

"Sandwich"

Sliding Tray

Adapter Pad

Solo Platform

Solo Shim

Texture Plate

Using Textured Impressions™Pro Embossing Folders

1. Open embossing folder and insert paper, cardstock or other embossable

material, making sure that the edge of the paper rests against the small

edge-blocks inside the die. Close the folder.

2. Place the closed Textured Impressions Pro Embossing Folder on top of the Big

 Shot™ProSoloPlatform(soldseparately).DONOTUSECUTTINGPADS

(Figure G). Place on top of the Adapter Pad in the Sliding Tray.

3. Follow Steps 3–5 in Operating Instructions, page 6.

Figure G

Textured Impressions Pro

Embossing Folder

Paper

Solo Platform

Textured Impressions Pro

Embossing Folder

• DiesperformbetterwhentheyareplacedrubbersideupontheSlidingTray.

• Diesperformbetterwhentheyareusedwithappropriatelysizedcuttingpads.

See Die and Accessory Compatibility Table on page 14.

• Foreasiercutting,placediesonTraydiagonally.

• UsetheBigShotProMachinetocutavarietyofdifferentmaterials.

See Materials Guide on page 13 for suggestions.

• Fewer sheets of material should be used when cutting very complicated shapes.

• When cutting felt, poly foam or delicate materials, place a scrap of paper over

the material to be cut.

• Use of Premium Crease Pad is required with Crease-Rule dies.

• UseonlyonesheetofmaterialwithCrease-Ruledies.

• Ifcreaseruleiscuttingthroughthematerialratherthancreasingthematerial,

place the die and material to be cut on the Adapter Pad diagonally (as size

allows) and then cut.

• ItisimportanttousetheDiePick(includedwiththeBigShotPro)toclean

 outthebitsofpaperandothermaterialthatbuildupinthejointsofthedies

(where the cutting rule meets). If dies are not kept clean, the scraps will

eventually push the rule slightly apart.

5. Helps & Hints

Figure I

Cutting Pad

(or Premium Crease Pad)

Paper

Die

Using Ellison®SureCut™or ClearCrop™Dies

Ellison SureCut and ClearCrop Dies can be used in the Sizzix Big Shot Pro Machine

without the Adapter Pad, as they are thicker than Sizzix Bigz Dies. Place SureCut

and ClearCrop dies directly on the metal Sliding Tray, rubber side facing up. Place

material to be cut against the rubber side of the die, then place one Cutting Pad on

top of the material (Figure I). For Ellison SureCut Crease-Rule Dies, place Premium

Crease Pad, instead of the Cutting Pad, on top of material to be cut. Follow Steps

3–5 in Operating Instructions, page 6.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIZZIX Cutter Handbücher

SIZZIX

SIZZIX Big Shot Express Bedienungsanleitung

SIZZIX

SIZZIX 660855 Bedienungsanleitung

SIZZIX

SIZZIX Eclips Bedienungsanleitung

SIZZIX

SIZZIX eclips2 Bedienungsanleitung

SIZZIX

SIZZIX eclips2 Bedienungsanleitung

SIZZIX

SIZZIX Eclips Bedienungsanleitung

SIZZIX

SIZZIX Big Shot Pro 660550 Bedienungsanleitung

SIZZIX

SIZZIX Big Shot Bedienungsanleitung

SIZZIX

SIZZIX eclips Tim Holtz Alterations Stamp2Cut No. 7 Bedienungsanleitung

SIZZIX

SIZZIX Big Shot Bedienungsanleitung

SIZZIX

SIZZIX Big Shot Machin Bedienungsanleitung

SIZZIX

SIZZIX Sidekick Bedienungsanleitung

SIZZIX

SIZZIX eclips2 Bedienungsanleitung

SIZZIX

SIZZIX BigKick Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung