4
By Searching Through the Library
If you cannot identify a correct Device Code for your equipment from the
Device Code list, you may search for the code in the library:-
1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. TV).
3. Hold down "CH +" and "VOL -" on the URC simultaneously for 2 seconds
until the indi ts up.
4. Enter a corresponding Magic Search Code from the following table. The
indicator ligh ould go out immediately.
(e.g. press "TV" device mode key, then press "CH +" and "VOL -", and
enter TV Magic Search Code 0001.)
5. Press the same desired device mode key again as in step 2 above. (e.g. TV)
6. Hold down "CH +" & "VOL -" simultaneously for 2 seconds until the
indicator and your URC is ready to start
searching.
7. Aim the URC at your device (e.g. TV), press the " " key slowly and
repeatedly until the device has been turned off.
Once your device has been turned off, immediately press Device Mode Key
(
* Simply repeat the above setup procedures to search for the Device Code
for your VCR, SAT, DVD or CTV. (Remember to press the correct Device
Mode Key and correct Magic Search Code in step 2-5 above)
cator under the power key ligh
t under the power key sh
light under the power key lights up,
e.g. TV) to lock in code and then indicator light under the power key should
go out.
- If the power on/off function of your device is not infra-red controlled, you
need to follow steps 2 to 6 above and start searching:-
- Press " " and another function key alternately until your device
responds to the expected function, then press the same Device Mode
Key (e.g. TV) to lock in the code.
e.g. Press " " & "1" alternately, or ;
Press " " & " " alternately.
DEVICE TYPE:
MAGIC SEARCH CODE:
TV VCR SAT CTV DVD
0001 0002 0003 0004 0005
IMPORTANT:
Note:
- DVD, CTV and other device codes can be searched for and locked into
any device modes except "TV" & "VCR" modes. Simply press the
corresponding device mode key in step 2 & 5 and enter an appropriate
Magic Search Code for your DVD, CTV and other devices.
- Each time you press the " ", the URC will skip to the next code and
send out a POWER signal trying to turn off your device.
If you fail to stop pressing " " in time when your device has been turned
code.
- If the indicator s twice after your
pressing of " " key, you are already at the last code of the library. Press
"CH +" and "VOL -" to resume the URC and repeat the above
procedures carefully to search again.
off, turn your device on again immediately. Before the indicator under the
power key goes out, press " "on the URC to skip backward. Repeat
step 7 above and lock in the
light under the power key flashe
5
Normal Operation
Once you have set up the URC for your A/V equipment, it works like your
original remote control. To operate, just aim it at your equipment, press an
appropriate device mode key and invoke the desired function by pressing a
corresponding key on the URC. The indica
flashes during signal transmission and as confirmation of key touch.
Punch Through
Punch Through Channel
Punch through channel allows you to operate channel up and down without
having to switch the device modes repeatedly even when your URC is in other
operating modes.
To activate the punch through channel setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "CH +" key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release "CH +"
To deactivate the punch through channel setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "CH -" key.
3. Press desired device Mode Key (e.g. SAT).
4. Release "CH -"
Punch Through Volume
Punch through volume allows you to operate volume up and down without
having to switch the device modes repeatedly even when your URC is in other
operating modes.
To activate the punch through volume setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "VOL +" key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release "VOL +" (the indicator flashes once if the
setting is activated).
To deactivate the punch through volume setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "VOL -" key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release "VOL -" (the indicator flashes twice if the
setting is deactivated).
tor light under the power key
(the indicator light under the power key flashes once if the
setting is activated).
(the indicator light under the power key flashes twice if the
setting is activated).
light under the power key
light under the power key
3OPERATING THE URC
F820-8360-0000
6
Macro Power
Macro Power allows you to turn two of your A/V equipment on/off
simultaneously.
To activate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold " " key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release " " (the indicator flashes once if the
setting is activated).
To deactivate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold " " key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release " " (the indicator flashes twice if the
setting is deactivated).
1. Do not expose your URC to dust, strong sunlight, humidity, high
temperatures or mechanical shocks.
2. Do not use old and new batteries together as old batteries tend to leak.
3. Do not use corrosive or abrasive cleansers on your URC.
4. Keep the unit dust free by wiping it with a soft, dry cloth.
5. Do not disassemble your URC, it contains no user-serviceable parts.
Q. My URC does not work at all!
A. Check your A/V device, if the device's main switch is turned off, your URC
cannot operate your device.
A. Check whether your batteries are inserted properly and are in the correct
+/- position.
A. Check whether you have pressed the corresponding device mode key for
your device.
A. If the batteries are low, replace the batteries.
Q. If several Device Codes are listed under the brand of my A/V device, how
can I select the correct Device Code?
A. To seek the correct Device Code for your A/V device, test the codes one by
one until most keys work properly.
Q. My A/V equipment responds only to some of the commands.
A. You have set a code for which only some commands work properly but
some do not. Try other codes until most keys work properly.
light under the power key
light under the power key
5TROUBLESHOOTING
4MAINTENANCE
380 x 180mm (fold to 95 x 180mm)
Universal Remote Control (URC)
Operating Instructions
123
456
789
0
ghi
pqrs
abc
def
jkl
mno
tuv
wxyz
R
,.-
A C T I V E
T V G U I D E P L A N N E R
VOL
VOL
CH
CH
M U T E B A C K
A S P E C T
BOX OFFICE/
ON DEMAND
AVSETUP
M E N U
H E L P
i
1
PRODUCT DIAGRAM KEY FUNCTION DESCRIPTIONS
1. Turns the power on or off for the selected device.
2. Order movies from Foxtel Box Office.
3. Displays Foxtels interactive services.
4. Displays Foxtels program listings screen.
5. Display your personal planner to view program reminders.
6. Turn the remote to Foxtel mode.
7. Turn the remote to TV mode.
8. Turn the TV to DVD mode.
9. Turn the TV to AUX mode.
10. Display more information about the program.
11. Display the setup screen to change the Foxtel settings.
12. Enter the Menu for the selected AV device.
13. Scroll through different AV modes.
14. Change channels up and down and pages up and down when
in TV guide.
15. Change volume up and down.
16. Confirms choices in menus and displays the i-search banner.
17. Navigate through menus.
18. Turns the sound on or off.
19. Jumps back to the previous screen or channel viewed.
20. Play when in DVD, VCR, CD or DVR mode.
21. Pause when in DVD, VCR, CD or DVR mode.
22. Rewind when in DVD, VCR, CD or DVR mode.
23. Fast-forward when in DVD, VCR, CD or DVR mode.
24. Record when in DVD, VCR or DVR mode.
25. Stop when in DVD, VCR, CD or DVR mode.
26. Used for selecting options in the Foxtel menus.
27. Change the aspect viewing ratio for your TV.
28. Takes you instantly to the Foxtel Help Channel.
29. Number pad for menus and changing channels.
2
BOX OFFICE/
ON DEMAND
A C T I V E
T V G U I D E
PLANNER
i
SETUP
M E N U
AV
CH
VOL
M U T E
B A C K
H E L P
A S P E C T
0-9
3
Congratulations! Your Universal Remote Control (URC) is a state-of-the-art
device which integrates many different infra-red remote controls to deliver
instant A/V action to your fingertips.
Before operating the remote, please read thoroughly (1) the inside of the
coversheet and (2) this manual. Then store them for future reference.
Alkaline batteries are recommended. The number of batteries required is
stated on the back of the coversheet.
1. Remove the battery cover on the back of your URC.
2. Check the polarity of the batteries and the "+/-" marks inside the battery
compartment.
3. Insert the batteries.
4. Push the battery cover back in place.
By entering Device Code
You may setup the URC by following the code entering instructions.
1. Referring to the DEVICE CODE LIST, look up the 4-digit Device Code
which corresponds to the brand of your A/V equipment. If there is more
than one Device Code listed under your brand, start from the first code.
2. Press the desired Device Mode Key (e.g. TV).
3. Hold down "CH +" and "VOL -" on the URC simultaneously for 2 seconds
until the indicator light under the power key lights up.
4. Use the number keys "0" - "9" to enter your 4-digit Device Code. The
indicator should go out immediately.
Turn on your device (e.g. TV), then try the function keys on the URC. If your
device (e.g. TV) responds to your activated function correctly, you have
entered the right Device Code. Otherwise, repeat the above steps with the
next available Device Codes until your device (e.g. TV) responds to your
activated function, and most keys work correctly.
* Simply repeat the above procedures to enter the Device Codes for your
DVD and AUX devices. (Remember to press the correct Device Mode Key
in step 2 above)
1HOW TO INSTALL THE BATTERIES
2HOW TO SET UP THE URC
Note:
If the indicat s twice in step 4, a wrong
Device Code has been entered. You are required to repeat step 2 to 4
again.
Suggestion :
- If you cannot find a correct Device Code for your equipment, see .
HOW TO SET UP THE URC - By Searching Through the Library.
- For future reference you are recommended to take a note of your Device
Codes in the space provided on the product's back label after setting up
the URC correctly.
or light under the power key flashe
2
380 x 180mm (fold to 95 x 180mm)
