
U P S
U P S
*Safety Notice*
The product contains voltages, which are potentially
hazardous. Qualified service personnel should
perform all repairs.
Do not try to open the cover and to service the
system yourself, no user serviceable parts inside.
Refer servicing to qualified service personnel only.
The product has its own internal energy source
(battery). The output receptacles may be live even
when the product is not connected to an AC supply.
*Warning*
In case of fire risky, please change the fuse with
the same kind and same rate or reset the breaker.
The product is intended for indoor use only. Kindly
note to avoid excessive heat, dust, humidity or
liquids.
MAINS
OUTLET
Description
UPS will turn on automatically when city power is back.
The AVR (Auto Voltage Regulator) is increasing (boost mode)
or reducing (buck mode) the input voltage to the UPS output.
The audible alarm is enabled. In the back-up mode a short
touch at the control button will reset the alarm mode. (This
function just can be used in UPS with touch button.)
In the normal mode, a short touch at the button will display I/P
frequency for 4seconds. (This function just can be used in UPS
with touch button.)
No
1
2
3
Indication
Auto turn-on
AVR mode
Alarm mode
Display of frequency
Battery capacity
Load level
Display of input & output
voltage
Estimated battery capacity, the accuracy is influenced by UPS
operation mode and load level.
The load level, percentage of full load.
When UPS is turned on, LCD will show input and output voltage,
6
7
4
5
Backup Mode
V
INPUT OUTPUT
%
%
V V
INPUT OUTP UT
%
%
AC Mode
AVR
AUTO
V V
INPUT OUTP UT
%
%
① ② ③
④
⑤
⑥ ⑦
%
%
AV R
AUTO
3.2 LCD Display
H
FREQENCY
100mm
100mm
100mm
THIS MANUAL CONTAINS IMPORTANT
SAFETY INSTRUCTIONS. KEEP THIS
MANUAL HANDY FOR FUTURE
REFERENCE.
INSTALLATION AND
OPERATION
The UPS is intended for indoor use only. Although your
UPS is very rugged, its internal components are not
sealed from the environment. Kindly note the following.
※Avoid direct sunlight.
※Avoid excessive heat.
※Avoid excessive humidity or liquids.
※Avoid excessive dust.
Before installation, please read and understand
the following instructions:
Inspect the following items inside box
※User’s Manual
※UPS
※Mains Cord
UNPACKING AND INSPECTION
Examine the packing carton for damage. Notify
your dealer immediately if damage is observed.
Store the packing in a safe place for possible future
trans-shipment of the UPS.
PLACE THE UPS
Position the UPS on a sturdy, dry surface in a well-
ventilated area away from direct sources of heat.
Leave at least 100 mm clearance all around the
UPS to provide adequate ventilation.
CONNECT UPS TO POWER
Connect the Power Cord, to a verified grounded 3-wire
receptacle. Do not power the UPS using a surge
suppressor or power strip. Switch the utility power ON.
BATTERY MAINTENANCE /
BATTERY CHARGING
AFTER SHIPMENT FROM THE FACTORY THE
BATTERY NEEDS RECHARGING. IF NOT USED
FOR A LONG PERIOD OF TIME, THE BATTERY
WILL START SELF-DISCHARGING, WHICH MAY
RESULT IN A SHORT SERVICE LIFE OF THE
BATTERY OR MAY EVEN CAUSE DAMAGE TO IT
DURING WARRANTY PERIOD. CARE SHOULD
ALSO BE TAKEN TO AVOID EXCESSIVE
TEMPERATURE AROUND THE UPS, WHICH COULD
ALSO RESULT IN REDUCING SERVICE LIFE OF
THE BATTERY. TO ACHIEVE MAXIMUM SERVICE
LIFE FROM THE BATTERY THE ABOVE
INSTRUCTIONS SHOULD BE FOLLOWED.
The UPS battery charges whenever the UPS is
connected to utility power & is switched ON. It typically
requires more than 12 hours to charge fully. Operating
runtime is reduced until the battery is fully charged.
The UPS is now ready to use. Switch on your
equipment and you are ready to function.
Enable the UPS by turning on the Power ON/OFF
switch, which is situated on the front panel.
CONNECT EQUIPMENT TO UPS
Now connect your load to be protected (computer,
monitor etc.) to the AC Output receptacles at the rear
of the UPS.
※Do not connect a Laser Printer or any
non-computer peripherals to UPS outlets.
※Do not connect a surge suppressor, power
strip, or extension cord to the UPS outlet.
12 HOURS
TIS 1291-2545
FUSE
250V~,6.0A
AC INPUT
220V~,50Hz
BYPASS
OUTPUT
OUTPUT
TIS 1291-2545
FUSE
250V~,6.0A
AC INPUT
220V~,50Hz
BYPASS
OUTPUT
OUTPUT
TIS 1291-2545
FUSE
250V~,6.0A
AC INPUT
220V~,50Hz
BYPASS
OUTPUT
OUTPUT
TIS 1291-2545
FUSE
250V~,6.0A
AC INPUT
220V~,50Hz
BYPASS
OUTPUT
OUTPUT
TIS 1291-2545
FUSE
250V~,6.0A
AC INPUT
220V~,50Hz
BYPASS
OUTPUT
OUTPUT