Skeye. E-motion HW 90400 Bedienungsanleitung

User Guide

skeye.e-motion

HW 90400

Version 1.02

This document and its contents shall not be re roduced or transferred in any form without

the event of atenting or registration of utility models.

Subject to amendment, errors exce ted

BHB_skeye-emotion_HW90400_1-02_EN.doc

TABLE OF CONTENTS

20.04.2012 • 1.02 3

Table of Contents

Introduction ................................................................................................. 5

1.1

Document Information ............................................................................... 5

1.2

Amendment Index ..................................................................................... 5

1.3

Terminology.............................................................................................. 5

1.4

Readershi ................................................................................................ 6

1.5

Intended Use ............................................................................................ 6

1.6

Safety Notes ............................................................................................. 6

1.6.1

General Safety Notes ........................................................................... 6

1.6.2

Safety Notes for the Lithium-Ion Battery................................................. 7

1.6.3

Safety Notes on the USB cradle / car cradle ...........................................10

1.6.4

Safety Notes on the Power Su ly ........................................................11

1.6.5

Safety Notes on the Imager with LED Aimer (o tional) ............................11

1.6.6

Safety Notes on GSM/GPRS/EDGE/UMTS/HSDPA ....................................11

1.6.7

Safety Notes on Wireless LAN/Bluetooth ................................................12

1.6.8

Safety Notes on GPS ...........................................................................12

1.6.9

Safety Notes on Data Loss ...................................................................12

1.7

Dis osal ..................................................................................................13

1.8

Ex lanations on this Manual .......................................................................13

1.8.1

Note Pictograms .................................................................................13

1.8.2

Registered Trademark .........................................................................14

skeye.e-motion ........................................................................................... 15

2.1

Views ......................................................................................................15

2.1.1

Front View .........................................................................................15

2.1.2

Side View...........................................................................................15

2.1.3

Rear View ..........................................................................................16

2.2

Accessories ..............................................................................................16

2.3

Cradle .....................................................................................................16

2.4

Hardware equi ment .................................................................................16

Taking into Operation ................................................................................. 17

3.1

Inserting the Micro SD Card .......................................................................17

3.2

Insertions of the SIM card..........................................................................18

3.3

Battery ....................................................................................................19

3.3.1

Inserting the Battery ...........................................................................19

3.3.2

Re lacing the Battery ..........................................................................21

3.3.3

Charging the Battery ...........................................................................21

3.4

Switching-on/Switching-off the skeye.e-motion ............................................22

3.4.1

Switching-on .....................................................................................22

3.4.2

Switching-off the skeye.e-motion..........................................................22

3.4.2.1

Sus end Mode (Standby Mode) ......................................................22

3.4.2.2

Automatic Standby – Power Su ly .................................................24

3.4.2.3

Com lete Power Off by Removing the Battery...................................25

Initial Steps ................................................................................................ 26

4.1

O erating the skeye.e-motion with the Stylus ..............................................26

4.2

Microsoft Windows CE – Basics ...................................................................27

4.2.1

Start Screen.......................................................................................27

4.2.2

Start Menu.........................................................................................27

4.2.3

Works ace Symbols ............................................................................28

4.2.4

Taskbar .............................................................................................28

4.2.5

Right Mouse Button Function ................................................................29

4.2.6

Showing/Hiding the Keyboard...............................................................29

4.2.7

Basic Settings.....................................................................................29

4.2.7.1

Calibrating the Touch Screen..........................................................30

4.2.7.2

Setting the Brightness ...................................................................32

Further Functions and Settings................................................................... 33

5.1

Scan of Barcodes ......................................................................................33

TABLE OF CONTENTS

1.02 • 20.04.2012

5.2

SysBacku ...............................................................................................33

5.2.1

Calling SysBacku ...............................................................................34

5.2.2

Creating a Backu ...............................................................................35

5.2.3

Restoring the Backu ..........................................................................36

5.2.4

Deleting a Backu ...............................................................................37

5.3

System Info .............................................................................................38

Radio .......................................................................................................... 0

6.1

Embedded Peri herals ...............................................................................40

6.2

Wireless LAN ............................................................................................40

6.2.1

WLAN Network Settings .......................................................................40

6.2.2

WLAN Configuration ............................................................................42

6.2.3

Entering the Network ID ......................................................................44

6.3

GSM Control.............................................................................................45

6.3.1

Establishing a connection.....................................................................45

6.3.2

Further Settings .................................................................................47

6.3.2.1

Persistent Setting of the PIN Number ..............................................47

6.3.2.2

General Settings ...........................................................................48

6.3.2.3

APN.............................................................................................49

6.3.2.4

GSM Info .....................................................................................49

6.4

GPS Module .............................................................................................50

USB Cradle/Car Cradle HW 51 00 .............................................................. 51

7.1

Technical Data..........................................................................................52

7.2

Placing the skeye.e-motion into the Cradle ..................................................53

7.3

Connecting the USB Cradle to the Deskto PC ..............................................53

7.4

Communication skeye.e-motion ⇔ PC .........................................................54

7.5

Connection of the Cradle in the Vehicle........................................................54

Technische Daten ....................................................................................... 56

Troubleshooting.......................................................................................... 57

9.1

Reset via Software ....................................................................................57

9.2

Reset via Hardware ...................................................................................57

INTRODUCTION

Document Information

20.04.2012 • 1.02 5

1. Introduction

The shock- and dirt resistant skeye.e-motion su orts all a lications in field

services and logistics. Due to rotection class IP45 (dust and humidity) and the fall

rotection (1.20 m) the skeye.e-motion can also be used in demanding

environments.

The multi-functional device is equi ed with a owerful Marvell PXA 320 @ 806 MHz

rocessor as well as a 256 MD DDR-RAM and u to 512 MB flash memory. Due to

the Windows Embedded CE 6.0 o erating system, the flexible terminal can be easily

integrated into existing IT infrastructures. The big 5.7" VGA TFT screen can dis lay

even com lex data and diagrams in easy-to-read fashion. A brightness sensor

automatically adjusts the sunlight readable dis lay to changing light conditions and

so ensures refect readability at all times.

Data transmission is in real-time using e.g. UMTS or WLAN. The GPS module is also

ca able for use in navigation and for locating vehicles. Mobile hone use via GSM is

made safe and convenient by the vehicle mounting kit with hands-free ca ability.

1.1 Document Information

Product: skeye.e-motion

Ty e of Document: User Guide

Version: 1.02

Date: 20.04.2012

Author: Lin

Höft & Wessel AG, Hannover

1.2 Amendment Index

Version: Changes: Date: By:

01.00 Translation 22.03.2010 GH

01.01 Correction of GPS baud rate/ ort 11.05.2010

Lin

01.02 Corrections; new cha ter 7.5 20.04.2012

Lin

1.3 Terminology

skeye.e-motion

HW 90400

Portable Data Terminal (in the following referred as

“mobile terminal”)

Battery HW 19400 The mobile terminal is su lied by a rechargeable lithium-

ion battery.

USB cradle

HW 51400

Cradle with USB interface for the mobile terminal.

Power su ly unit HW 1430 Wide range switched mode ower su ly unit to rovide

the mobile terminal and the USB cradle with ower.

Car cradle HW 51400 For installation of the skeye.e-motion in vehicles and for

charging of the battery.

INTRODUCTION

Readershi

6 1.02 • 20.04.2012

1. Readership

The documentation is intended for eo le o erating the skeye.e-motion.

1.5 Intended Use

The skeye.e-motion has been designed for use in the commercial sector and for

acquiring and transferring data within buildings or vehicles or outside under

moderate climate conditions.

The skeye.e-motion is not intended for distribution to rivate households.

Please ay attention to the information of this user guide, es ecially the safety

notes. Intended use means that the device must only be used and o erated in

accordance with the information contained herein. Any other use is not an intended

use and may lead to ro erty damage or even ersonal injury. Höft & Wessel does

not acce t any liability for damages caused by a usage other than the intended

usage.

1.6 Safety Notes

Carefully read and follow the user manual and the safety information mentioned in

this cha ter before erforming further ste s. You have to:

•read

•kee the information in mind during work.

This is the recondition for

•secure working with the roduct

•undisturbed handling

1.6.1 General Safety Notes

Transport and Storage:

♦The device must only be shi ed in original or com arable robust ackaging.

Shi ing the device e.g. in a normal added bag does not rovide sufficient im act

and ressure rotection.

Such im ro er ackaging would fall under the definition of the term Negligence.

Handling:

♦Never ex ose the skeye.emotion to very high tem eratures for a long time.

♦Never insert any objects not intended for use with this device in the instrument’s

o enings. This might damage the device.

Operating:

♦Do not di the skeye.e-motion into fluid.

♦Only use your skeye.e-motion with original equi ment. Non-com liance voids the

warranty.

♦Do not o erate your skeye.e-motion when you are in ex losive areas, for instance

in etrol stations, fuel de ots, chemical lants, below deck in shi s, near blasting

o erations, in locations where a large volume of dust articles (such as flour, wood

INTRODUCTION

Safety Notes

20.04.2012 • 1.02 7

or metal) is resent in the air, etc.

We recommend to switch off the device com letely. This also a lies to laces

where you are usually advised to switch off your vehicle motor.

♦Do not o erate in close range of strong electromagnetic fields. Failures may be

caused.

♦Interference may be noticed near electric devices. Therefore, always ay attention

to local safety regulations.

♦Users with hearings aids must note that radio signals of electronic devices (with

radio equi ment) may launch into hearing devices causing an un leasant noise.

Maintenance, Service and disturbances:

♦The skeye.e-motion is – a art from charging of battery and the mentioned

comments – lifetime maintenance-free and does not need s ecial care.

♦Do not try to o en, re air or modify your skeye.e-motion. The manufacturer will not

be liable for any damage caused in that way. A art from other things, the function

for correctly charging the battery may be influenced. As a result, excessive charging

voltage, uncontrolled charging and discharge current, leakage of harmful

substances, excessive heat generation, bursting or fire may occur.

♦Any tam ering by non-authorised ersons will invalidate the warranty.

♦If your skeye.e-motion needs to be re aired or maintained, lease contact your

s ecialised dealer.

♦Clean the housing only with dam cloth and mild detergent.

1.6.2 Safety Notes for the Lithium-Ion Battery

Carefully read the following safety notes to revent an incorrect handling of the

battery and to avoid ossible dangers.

Non-observance of the safety information or incorrect use of the battery

can lead to excessive current flow, to the discharge of harmful substances,

excessive heat development, explosion or fire.

Transportation and storage:

♦Do not trans ort or store the battery together with metal objects such as necklaces,

hair ins, etc. Doing so may short circuit the battery, which could result in excessive

current flow and ossibly cause leakage of battery fluid, heat generation, bursting

or fire. When carrying or storing batteries, use an electrically nonconductive

(insulated) case.

♦When the equi ment is ex ected not to be used for a long time do not store the

batteries exceeding the a ro riate conditions as listed below. Otherwise its

erformance will be degraded and its service life will be decreased.

▪when the batteries are discharged and remain in the equi ment: 1 week

▪when the batteries are fully charged and remain in the switched off

equi ment: 1 month

▪long-term storage: see next note.

♦When the battery is ex ected not to be used for a long time, take the battery out of

the equi ment and store it in a dry lace at or below room tem erature. For an

o timum service life, the battery should be charged u to 20 to 40% when being

stored. After 12 months at the latest the device should be charged and

INTRODUCTION

Safety Notes

8 1.02 • 20.04.2012

subsequently discharged. Otherwise, its erformance will be degenerate and its

service life will be decreased.

♦The storage tem erature must not be below –20 or above +50°C.

Ambient conditions:

♦The tem erature may not be outside the admissible o erating and storage

tem erature range of -20 to +50 degrees centigrade. The tem erature may be

within the range of 0 °C to +40 °C during charging.

♦Do not discard the battery into fire and do not leave it in a hot lace such as near a

fire or on a heater. Doing so melt the insulation, damage the sealing arts or

rotective devices, cause leakage of battery fluid (Electrolyte) from the batteries,

bursting or fire.

♦Do not immerse batteries in water or seawater, and do not allow them to become

wet. Batteries which have become wet must always be re laced with new ones

because internal short-circuits can cause dangerous heat emissions if further used.

♦Do not throw batteries, and do not allow them to fall on hard surfaces.

Connection:

♦Do not connect the battery to an electrical outlet, e.g. vehicle cigarette lighter,

ower outlets, other ower su ly units, other charger, etc.

♦Do not reverse the ositive (+) and negative (-) terminals when inserting the

battery. Since the mechanical design of the battery enables you to insert in one

direction only, the battery must not be inserted into the o osite direction by force.

Handling:

♦Protective devices to revent danger are built into the battery. To ensure for a

ro er o eration, do not disassemble the battery or modify arts of it. If they are

damaged, this could result in excessive charging voltage, control loss during

charging or discharging, leakage of battery fluid, heat generation, bursting or fire.

♦Do not disassemble Li-ion bare cells of the battery. There is the danger of flammable

fluid being s ilt. It may also cause an internal or external short circuit, leakage of

battery fluid, heat generation, bursting or fire.

♦Do not directly solder the battery. Doing so melt the insulation, damage the sealing

arts or rotective devices, cause leakage of battery fluid (Electrolyte) from the

batteries, bursting or fire.

♦Do not short-circuit the battery by directly connecting the ositive (+) and negative

(-) terminals with objects such as wire. Short circuiting generates heat which may

damage the equi ment. In the worst case this could result in leakage of battery

fluid, bursting or fire.

♦Do not ut the battery into a microwave oven or ressurised container. This could

result in leakage of battery fluid, bursting or fire.

♦Do not ierce the battery with a nail or other shar object, hit it with a hammer, or

ste on it. This could result in leakage of battery fluid, bursting or fire.

Operation:

♦For o eration of the device use the delivered battery only. Please use the battery

only for the determined ur ose.

INTRODUCTION

Safety Notes

20.04.2012 • 1.02 9

♦Do not use the battery in any device other than those s ecified in this manual.

De ending on the device being used, doing so may cause abnormal current flow,

leakage of battery fluid, heat generation, bursting or fire.

♦If the battery becomes discolored or deformed, or in any way a ears abnormal,

sto using it. Return it to the distributor or manufacturer from whom you urchased

it.

♦Do not use or leave the battery in very high tem eratures (for exam le, under

strong direct sunlight). Otherwise, it may cause leakage of battery fluid, bursting or

fire or its erformance will be degenerate and its service life will be decreased.

♦To ensure safety, the battery incor orates built-in safety devices. Do not use it in a

location where static electricity is greater than what the manufacturer guarantees.

Otherwise, the safety devices may be damaged, causing leakage of battery fluid,

ex ose of fire.

♦Do not use the battery in other than the following conditions. Otherwise, it can

overheat or fire, or its erformance will be degenerate and its service life will be

decreased.

▪when the battery is charged: 0 °C ~ +40 °C

▪when the battery is stored: -20 °C ~ +50 °C

Note: higher tem eratures increase the self-discharge of the battery.

♦Do not connect different assembled batteries together. And also do not connect

same assembled batteries in series, unless ex licitly instructed by the user

information to do so.

Charging:

♦When recharging, only use the battery charger s ecially rovided by Skeye. Failure

to follow ro er charging rocedures may cause excessive voltage, excessive

current flow, loss of control during charging, leakage of battery fluid, heat

generation, bursting, or fire.

♦Do not use or charge the battery near a heat source such as fire or heater or in

extremely hot weather.

♦Do not charge a battery when it is cold (below 0 °C). This may cause im aired

erformance and shortening of battery service life.

♦If a battery is to be used for the first time or it has not been used for a long time,

be sure to charge it.

Health hazards:

♦If a battery leaks, and the electrolyte enters the eye, do not rub but rinse out

thoroughly under flowing water and then seek medical assistance. Otherwise, eye

damage can result.

♦If a battery leaks and the electrolyte makes contact with clothing or the skin, the

skin or clothing must be rinsed out under flowing water in order to revent damage

to the skin.

Maintenance, service and disturbances:

♦Lithium-ion batteries have a redetermined o erating life. If the o erating time

shortens excessively, this means that the battery life has ex ired. If it comes to

that oint, sto use immediately and re lace with new batteries.

INTRODUCTION

Safety Notes

10 1.02 • 20.04.2012

Old batteries as well as device storage batteries must not be dis osed of with

your household waste. Consumers are obliged to return batteries to a suitable

collection oint (trade, munici ality). Device batteries can be returned to Höft &

Wessel after use at no cost as well. Old batteries may contain heavy metals or

harmful substances that may cause damage to environment and health.

Batteries are reusable. They contain im ortant raw materials like iron, zinc,

manganese, and nickel.

Höft & Wessel (see address on last age) guarantees that all batteries returned

are fed to the recycling rocess.

See also the extract from the BattG (act concerning the lacing on the market,

collection and environmentally com atible waste management of batteries and

accumulators) of 25.06.2009.

According to §9, section 1, sentence 1, manufacturers are obliged to take back

batteries that have been handed in by distributors or public disposal

departments (here, device batteries registered according to §13, sentence 1)

free of charge and to treat and recycle them according to §14 Batteries that

cannot be treated and recycled shall be disposed of according to §14

♦If Lithium-ion batteries are not fully charged after the battery charger’s

redetermined charging eriod has ela sed, sto the charging rocess. Prolonged

charging may cause leakage of battery fluid, heat generation or bursting of fire.

♦If the battery leaks or gives off a bad odor, remove it from any ex osed flame.

Otherwise, the leaking electrolyte may catch fire, and the battery may ex lode or

fire.

♦If the battery gives off an odor, generates heat, becomes discolored or deformed, or

in any way a ears abnormal during use, recharching or storage, immediately

remove it from the device or battery charger and sto using it.

♦In case the battery terminals are dirty, clean the terminals with a dry cloth before

use, otherwise, the contact with equi ment may cause insufficiency, and ower

failure or charge failure.

1.6.3 Safety Notes on the USB cradle / car cradle

♦The battery may only be charged with the battery charging device recommended by

the manufacturer. The utilisation of another battery charger might be dangerous

and leads to an end of the warranty.

♦Do not try to o en, re air or modify your device. The manufacturer will not be liable

for any damage caused in that way. A art from other things, the function for

correctly charging the battery may be influenced. As a result, excessive charging

voltage, uncontrolled charging and discharge current, leakage of harmful

substances, excessive heat generation, bursting or fire may occur.

♦If the USB cradle/car cradle changes sha e or colour, generates heat or in any way

a ears abnormal sto using it. Return it to the distributor or manufacturer from

whom you urchased the USB cradle/car cradle.

♦Use the USB cradle/car cradle only with the su lied ower su ly. The main

voltage must corres ond to the technical data mentioned on the ower su ly.

♦Use the USB cradle/car cradle only in dry, closed rooms and not in direct sunlight,

e.g. behind windows.

♦Kee the device out of the reach of small children.

Andere Handbücher für e-motion HW 90400

Inhaltsverzeichnis

Andere skeye. Handheld Handbücher

skeye.

skeye. HW 90240 Bedienungsanleitung

Beliebte Handheld Handbücher anderer Marken

Honeywell

Honeywell Dolphin 9900 Bedienungsanleitung

Honeywell

Honeywell CN75 Bedienungsanleitung

MiTAC

MiTAC Mio 168 Bedienungsanleitung

Wasp

Wasp WDT92 Bedienungsanleitung

Texas Instruments

Texas Instruments TI-Nspire Bedienungsanleitung

AXEM Technology

AXEM Technology MBS Bedienungsanleitung

Armstrong

Armstrong Brain Wave Montageanleitung

Unitech

Unitech TB128 Bedienungsanleitung

Symbol

Symbol MC9000-G Installations- und Betriebshandbuch

Unitech

Unitech HT1 1D Batch Bedienungsanleitung

Ingenico

Ingenico IWL220 GPRS Bedienungsanleitung

Intermec

Intermec CK61 Bedienungsanleitung

Symbol

Symbol c2000 Bedienungsanleitung

Symbol

Symbol MC18 Installations- und Betriebshandbuch

Acer

Acer n20 Bedienungsanleitung

Intermec

Intermec CK61 Bedienungsanleitung

Docomo

Docomo F-04H Bedienungsanleitung

Toshiba

Toshiba e350 Series Bedienungsanleitung

skeye. e-motion HW 90400 Bedienungsanleitung

Beliebte Handheld Handbücher anderer Marken