Skil PI0300C-00 Bedienungsanleitung
WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et
comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide afin
de pouvoir le consulter ultérieurement.
ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender
el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para
consultarlas en caso sea necesario.
Owner’s Manual
Guide d’utilisation
Manual del propietario
For Customer Service
Pour le service à la clientèle
Servicio al cliente 1-877-SKIL-999 OR www.skil.com
40V 300W Power Inverter
Convertisseur continu-alternatif de 40 V, 300 W
Inversor de alimentación de 40 V y 300 W
Model/ Modelo/ Modèle: PI0300C-00
2
TABLE OF CONTENTS
Important Safety Instructions......................................3
FCC Caution....................................................5
Symbols .......................................................6
Get to Know Your Power Inverter ..................................9
Specications ..................................................9
Operating Instructions ..........................................10
Maintenance...................................................13
Troubleshooting ...............................................13
Limited Warranty of SKIL Consumer Tools..........................14
3
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
WARNING When using this product, basic precautions should always be followed,
including the following:
▘Read all the instructions before using the product.
▘To reduce the risk of injury, close supervision is necessary when the product is used near
children.
▘Do not put ngers or hands into the product.
▘Use of an attachment not recommended or sold by power pack (inverter) manufacturer
may result in a risk of re, electric shock, or injury to persons.
▘To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord
when disconnecting the power pack (inverter).
▘Do not use a battery pack or appliance that is damaged or modied. Damaged or modied
batteries may exhibit unpredictable behavior resulting in re, explosion, or risk of injury.
▘Do not operate the power pack (inverter) with a damaged cord or plug, or a damaged
output cable.
▘Do not disassemble the power pack (inverter), take it to a qualied service person when
service or repair is required. Incorrect reassembly may result in a risk of re or electric
shock.
▘To reduce the risk of electric shock, unplug the power pack (inverter) from the outlet before
attempting any instructed servicing.
▘When charging the internal battery, work in a well ventilated area and do not restrict
ventilation in any way.
▘Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
▘Do not expose a power pack (inverter) to re or excessive temperature. Exposure to re or
temperature above 265 °F (130 °C) may cause explosion.
▘Have servicing performed by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the product is maintained.
WARNING Read all safety warnings and instructions. Failure to follow the warnings
and instructions may result in electric shock, re and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
▘Risk of fire and electric shock. Dry location use only. Do not expose the power
inverter to rain or wet conditions. Water entering the power inverter will increase the
risk of electric shock.
▘For household use only.
▘Do not allow the power inverter to be used as a toy. Close attention is necessary when
used by or near children.
▘The power inverter is not intended for any use other than charging small USB
electronics or small AC devices specied in SPECIFICATIONS in this manual. Any
other use may result in damage.
▘Switch off the power inverter when not in use.
▘Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to battery pack, picking up or carrying the power inverter. Carrying the
4
power inverter with your finger on the switch or energizing power inverter that has the
switch on invites accidents.
▘Disconnect the battery pack from the power inverter before making any
adjustments, changing accessories, or storing power inverter. Such preventive safety
measures reduce the risk of starting the power inverter accidentally.
▘Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
battery pack.
▘Use power inverter only with specically designated battery packs. Use of any other
battery packs may create a risk of injury and re.
▘Use only with the battery packs and chargers listed below:
BATTERY PACK CHARGER
SKIL BY0800C-00, SKIL BY8705-00,
SKIL BY8708C-01, SKIL BY8708-00,
SKIL BY8723C-00, SKIL BY3000C-00
SKIL SC5376C-00, SKIL SC5364-00,
SKIL SC0320C-00
▘When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a re.
▘Follow all charging instructions and do not charge the battery pack or appliance
outside of the temperature range specied in the instructions. Charging improperly or
at temperatures outside of the specied range may damage the battery and increase the
risk of re.
▘Do not modify or attempt to repair the power inverter or the battery pack except as
indicated in the instructions for use and care.
▘Store idle power inverter out of the reach of children and do not allow persons
unfamiliar with the power inverter or these instructions to operate the power
inverter. Power inverters are dangerous in the hands of untrained users.
▘Maintain power inverter and accessories. Check for misalignment or breakage of
parts and any other condition that may affect the power inverter’s operation. If
damaged, have the power inverter repaired before use. Many accidents are caused by
poorly maintained power inverter.
▘Save these instructions. Refer to them frequently and use them to instruct others who
may use this product. If you lend this product to someone else, also lend these instructions
to them to prevent misuse of the product and possibly injury.
SAVE THESE INSTRUCTIONS!
5
FCC CAUTION
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
▘Reorient or relocate the receiving antenna.
▘Increase the separation between the equipment and receiver.
▘Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
▘Consult the dealer or an experienced radio/TV technician for help.
6
SYMBOLS
Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety
symbols and explanations with them deserve your careful attention and understanding. The
symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings
they give are no substitutes for proper accident prevention measures.
WARNING Be sure to read and understand all safety instructions in this Owner’s
Manual, including all safety alert symbols such as “DANGER”, “WARNING”
and “CAUTION” before using this tool. Failure to follow all instructions listed below may result in
electric shock, re, and/or serious personal injury.
The denitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous
situation which, if not avoided, will result in minor or moderate
injury.
Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment
or other properly damage if they are not followed. Each message is preceded by the word
“NOTICE”, as in the example below:
NOTICE: Equipment and/or properly damage may result if these instructions are not followed.
WARNING The operation of any power tools can result in foreign
objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face
shield when needed. We recommend a Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always
use eye protection which is marked to comply with ANSI Z87.1.
7
SYMBOLS (CONTINUED)
IMPORTANT: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate the
tool better and more safely.
Symbol Name Designation/Explanation
V Volts Voltage (potential)
AAmperes Current
Hz Hertz Frequency (cycles per second)
WWatt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
Wh Watt-hours Battery capacity
Ah Ampere-Hours Battery capacity
øDiameter Size of drill bits, grinding wheels, etc.
n0No load speed Rotational speed, at no load
nRated speed Maximum attainable speed
…/min Revolutions or reciprocation per
minute (rpm)
Revolutions, strokes, surface speed,
orbits, etc. per minute
OOff position Zero speed, zero torque...
1,2,3,…
Ⅰ,Ⅱ,Ⅲ, Selector settings Speed, torque or position settings.
Higher number means greater speed
Innitely variable selector with off Speed is increasing from 0 setting
Arrow Action in the direction of arrow
Alternating current (AC) Type or a characteristic of current
Direct current (DC) Type or a characteristic of current
Alternating or direct current
(AC / DC) Type or a characteristic of current
Class II tool Designates Double Insulated Construction
tools.
Protective earth Grounding terminal
Li-ion RBRC seal Designates Li-ion battery recycling
program
8
Symbol Name Designation/Explanation
Read the instructions Alerts user to read manual
Wear eye protection symbol Alerts user to wear eye protection
Always operate with two hands Alerts user to always operate with two
hands
Do not use the guard for cut-off
operations
Alerts user not to use the guard for
cut-off operations
SYMBOLS (CERTIFICATION INFORMATION)
IMPORTANT: Some of the following symbols for certication information may be used on your
tool. Please study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and more safely.
Symbol Designation/Explanation
This symbol designates that this tool is listed by Underwriters
Laboratories.
This symbol designates that this component is recognized by
Underwriters Laboratories.
This symbol designates that this tool is listed by Underwriters
Laboratories, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Canadian
Standards Association.
This symbol designates that this tool is listed by the Canadian
Standards Association, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Intertek Testing
Services, to United States and Canadian Standards.
This symbol designates that this tool is listed by the SGS Testing
Services, to United States and Canadian Standards.
9
GET TO KNOW YOUR POWER INVERTER
40V 300W Power Inverter
Fig. 1
Power Button
Latch
Battery Contacts
LED Button
LED Light
Carrying Handle
USB-A Output Port
USB-C Output Port 1
USB-C Output Port 2
AC Output
Port
SPECIFICATIONS
Voltage 40 V
Output Wave Form Pure Sine Wave
USB-A Output 5V 2.1A
USB-C Output 1 5V/9V/12V 3A, 20V 3.25A, up to 65W
USB-C Output 2 5V 3A, 9V 2A, 12V 1.5A, up to 18W
AC Output (Receptacle) 120V ~ 60Hz, 300W Continuous, 500W Peak
more than 3 seconds
Weight (Without battery pack) 2.27 lb (1.03 kg)
Recommended charging temperature 41°F - 104°F (5°C - 40°C)
Recommended storage temperature 32°F – 104°F (0 – 40°C)
10
OPERATING INSTRUCTIONS
WARNING To reduce the risk of re, personal injury, and product damage due to
a short circuit, never immerse your power inverter, battery pack, or
charger in uid or allow a uid to ow inside them. Corrosive or conductive uids, such as
seawater, certain industrial chemicals, bleach or bleach-containing products, etc. can cause a
short circuit.
WARNING Do not attempt to modify the power inverter or create accessories not
recommended for use with this power inverter. Any such alteration or
modication is misuse and could result in a hazardous condition leading to possible serious
injury.
INSTALLING/REMOVING BATTERY PACK (Fig. 2)
NOTE: Fully charge the battery pack before
rst use.
To install battery pack
Align the mounting slots on the power inverter
with the ribs on the battery pack, then slide the
battery pack until it snaps into position on the
power inverter.
WARNING Make sure that the latch on
the power inverter snaps
into place and the battery pack is secured to
the power inverter before beginning operation.
Failure to securely seat the battery pack could
cause the battery pack to fall out, resulting in
serious personal injury.
To remove battery pack
Hold the battery pack with one hand and pull the power inverter with the other hand to
separate them.
WARNING Always be aware of location of your feet and children or pets around you
when separating the battery pack from the power inverter. Serious injury
could result if the battery pack falls. NEVER remove the battery pack at a high location.
WARNING Always remove the battery pack when the power inverter is not in use.
TURNING POWER INVERTER
ON/OFF (Fig. 3)
1. Install the battery pack.
2. To turn the power inverter on, press the
power button and the button will illuminate
green, which indicates that the power
inverter is activated.
3. To turn the power inverter off, press the
power button again and the green light
will turn off, which indicates that the power
inverter is deactivated.
Fig. 2 Rib
Mounting
Slot
Fig. 3
LED Button
Power Button
LED Light
Inhaltsverzeichnis
Sprachen:
