Sky Ready RC Cobra Handbuch

Cobra / Cobra Lite Build Instructions

Parts List:

(2) Aluminum CLS plates

(1) Carbon fiber bottom plate (3mm)

(1) Carbon fiber top plate (2mm)

(4) Carbon fiber arms (5mm)

(4) 25mm aluminum standoffs

(1) TPU camera mount

(1) TPU eccentric camera bushing (left)

(1) TPU eccentric camera bushing (right)

(1) TPU SMA antenna mount

(1) TPU receiver antenna tube holder

(1) Receiver antenna tube

(2) Receiver antenna tube caps

(2) 2x6mm camera screws

(2) 1mm camera screw washers

(4) 3x16mm screws

(4) 3x10mm screws

Cobra / Cobra Lite Build Instructions

Step 1: Insert two arms into an aluminum CLS plate. Make two.

Cobra / Cobra Lite Build Instructions

Step 2: Place the bottom plate into corresponding slots in the CLS plates. The single triangular cutout in the bottom

plate indicates the front of the quad.

Cobra / Cobra Lite Build Instructions

Step 2 (Continued):

Cobra / Cobra Lite Build Instructions

Step 3: Install (4) 3x16mm screws into the four holes in the bottom plate. Use blue (medium) thread lock. Install (4)

25mm standoffs onto the screws.

Cobra / Cobra Lite Build Instructions

Step 4: Press the eccentric camera bushings into the camera mount from the outside of the camera mount. The

bushings should fit flush with the sides of the camera mount when installed properly. The bushings have an off-center

hole, allowing the camera mount to be compatible with different length camera lenses. Orient the bushings so that

your camera lens does not stick out too far, but also so the top plate is not in view.

Step 5: Slide all TPU parts onto the standoffs as shown.

Cobra / Cobra Lite Build Instructions

Step 6: Place the top plate on the standoffs, and secure with (4) 3x10mm screws.

Cobra / Cobra Lite Build Instructions

Step 7: After assembling the frame, feed your receiver antenna wires into the back (smaller) holes of the TPU antenna

tube holder and run them out the front (larger) holes. Cut the antenna tube to the length of your exposed receiver

antenna wires. Slide the receiver antenna into the antenna tube and press the antenna tube into the hole of the TPU

antenna tube holder on each side. Place an antenna tube cap on each antenna tube.

Cobra / Cobra Lite Build Instructions

Exploded View

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sky Ready RC Drohne Handbücher

Sky Ready RC

Sky Ready RC Reflex Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

dji

dji Matrice M210 Bedienungsanleitung

MAKE

MAKE Terry Kilby Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

dji

dji PHANTOM 4 Bedienungsanleitung

Atlas

Atlas AtlasPRO Bedienungsanleitung

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

dji

dji WIND-4 Bedienungsanleitung