SKY-WATCHER ESPRIT 120 ED Super APO Bedienungsanleitung

INSTRUCTION MANUAL

ESPRIT 120 ED Super APO

SL301113

Table of contents

Table of Contents

Introduction........................................................................................................................................ 2

Getting started................................................................................................................................... 3

Parts description .................................................................................................................................. 3

Unpacking the telescope...................................................................................................................... 3

Preparing the telescope for an observation.......................................................................................... 4

Cooling the telescope .......................................................................................................................... 4

Aligning the finder scope .................................................................................................................... 5

Using the telescope for visual observation............................................................................ 6

Inserting the eyepiece.......................................................................................................................... 6

Focusing .............................................................................................................................................. 6

Prime focus imaging with the optional field flattener....................................................... 7

Installing the field flattener and a DSLR (Digital Single-Lens Reflex) camera ...................................... 7

Installing a 48mm filter inside the extender tube .................................................................................. 8

Installing the field flattener and a CCD (Charge-Coupled Device) camera ............................................ 8

Focusing .............................................................................................................................................. 9

Framing the picture ............................................................................................................................. 9

Useful tips for all observations ................................................................................................ 13

Removing the finder scope................................................................................................................ 13

Using the indexed scale..................................................................................................................... 13

Prime focus imaging with the optional 0.77x reducer / flattener................................ 10

Installing the reducer flattener and a DSLR camera ............................................................................ 10

Installing the reducer flattener and a CCD camera ....................................................... ..................... 11

Specifications.................................................................................................................................. 14

Telescope & telescope accessories & threads specifications.......................................................... 14

Different releases: Case ................................................................ .............................................. 16

Introduction

The spirit of perfection, by Sky-Watcher

Designed with the discerning astronomer in mind, Sky-Watcher top-of-the-line Esprit refractors

deliver the kind of imaging performance one would expect from telescopes costing much more. With

their three-element air spaced objective lens design, false color is extremely well corrected, yielding

exceptional contrast and sharpness.

The 3" CNC machined 1:11 rotatable dual speed linear power focuser provides a smooth, rock-solid

focusing with zero image shifts. The Esprit ED 120mm refractor comes with a 9 x 50 right angle

finder scope, 2-inch Star diagonal, D-style dovetail, retractable dew cap and padded case.

Quick overview:

120 mm apochromatic, 3-element refractor

840 mm (f/7)

Metallic high-transmission lens coatings

3" CNC machined 1:11 dual-speed focuser

No visual color fringing even on bright objects

Knife-edge Baffled Optical System

2" Diagonal with dielectric coatings

9x50 erect-image 90° finder scope

Tube rings with dovetail D (Losmandy style) bar

Aluminum foam lined case

Optional thread-on full frame field flattener

Optional thread-on full frame 0.77x reducer /

field flattener

NEVER USE YOUR TELESCOPE TO LOOK DIRECTLY AT

THE SUN. PERMANENT EYE DAMAGE WILL RESULT.

NEVER USE AN EYEPIECE-TYPE SOLAR FILTER.

NEVER USE YOUR TELESCOPE TO PROJECT SUNLIGHT

ONTO ANOTHER SURFACE; THE INTERNAL HEAT BUILD-

UP WILL DAMAGE THE TELESCOPE OPTICAL ELEMENTS.

USE A PROPER SOLAR FILTER FIRMLY MOUNTED ON THE

FRONT OF THE TELESCOPE FOR VIEWING THE SUN.

WHEN OBSERVING THE SUN, PLACE A DUST CAP OVER

YOUR FINDERSCOPE OR REMOVE IT TO PROTECT YOU

FROM ACCIDENTAL EXPOSURE.

NEVER LET A TELESCOPE POINTING THE SUN

UNATTENDED.

Getting started

Parts description

1. Retractable dew cap

2. Tube rings

3. D (Losmandy) dovetail bar

4. 9x50 erect-image 90° finder

scope

5. 3" 1:11 dual-speed focuser

6. 2" dielectric diagonal

7. 2" eyepiece f= 28mm

Unpacking the telescope

Your telescope is inside the sturdy aluminum padded case,

designed to securely carry the telescope and the tube rings. The

case has two castors on one side to facilitate transport.

The case contains and protects the telescope and its accessories. Once open you will find:

1. The telescope with dew cap retracted.

2. The 9x50 erect-image finder scope

with tube rings and mount.

3. The 2" (50.8mm) diagonal.

4. The 2-element thread-on field flattener

(used for photography only),

guarantees excellent field flatness

across the entire 44 mm imaging

plane, allowing picturing the sky with

large sensors.

5. Field flattener extender tube for DSLR

camera, used to place the camera

exactly on the corrected focal plane.

6. 2" eyepiece, f= 28mm.

7. Thread-on field flattener adaptor, used

to install the field flattener on the

focuser's drawtube.

Some parts may be optional,

depending on the dealer's

country.

Please check with him if any

doubt.

Preparing the telescope for an observation

A. Upon delivery, and when not used, the

telescope and its accessories are inside the

aluminum padded case. Unpack the

telescope and assemble it to your mount

using the included D (Losmandy style)

dovetail bar. Please refer to your mount

manual to properly install the telescope.

B. To extend the dew cap unscrew the two

screws on the aluminum ring (1), then

gently pull the dew cap forward (2). When

in position, tighten the two screws to

ensure the dew cap stays in position.

C. The 9x50 erect-image finder scope is a

small fixed magnification scope mounted

on the optical tube. When it is correctly

aligned with the telescope, objects can be

quickly located and brought into the field

of telescope (see also "Aligning the finder

scope" chapter, on next page)

To install the finder scope on the telescope

insert the positive dovetail of the finder

scope support inside the negative dovetail

mounted on the focuser, as shown in

picture.

Cooling the telescope

Telescopes require time to cool down to outside air temperature. This may take longer if there is a big

difference between the temperature of the telescope and the outside air. This minimizes heat wave

distortion inside telescope tube (tube currents). Your telescope would require at least 25 minutes

cooling off to outside conditions. Tip: use this time for planning your session and mount accessories.

Aligning the finder scope

The 9x50 erect-image finder scope is a small fixed magnification scope mounted on the optical tube.

When it is correctly aligned with the telescope, objects can be quickly located and brought to the

center of the field.

The alignment should be done at first use and over time if the alignment is no more accurate.

Alignment is best done outdoors in day light when it's easier to locate objects

If it is necessary to refocus your finder scope, sight on an object that is

at least 500 meters (or yards) away. Loosen the locking ring by

unscrewing it back towards the bracket. The front lens holder can now

be turned in and out to focus. When focus is reached, lock it in position

with the locking ring

Choose a distant object that is at least 500 meters (or yards) away and

point the main telescope at the object. Adjust the telescope so that the

object is in the center of the view in your eyepiece.

If you are using the star diagonal the image will be left/right

inverted, like images in a mirror.

Having an erected image, the view you have in the finder

scope has the same orientation as the landscape.

Check the finder scope to see if the object, centered in the

main telescope view, is centered on the crosshairs. If not

unscrew the three blocking rings on the rear ring, then adjust

the three small screws to center the finder scope.

Do not over tighten the screws when aligning the finder

scope. When the finder scope is correctly oriented, screw the

three blocking rings in position.

Using the telescope for visual observation

Inserting the eyepiece Loosen the two thumbscrews (1)

on the end of the focuser tube.

Insert the 2" diagonal (2) into the

focus tube and re-tighten the

thumbscrews (1) to hold the

diagonal in place.

Loosen the diagonal's screw (3).

For 2" eyepieces (4a), insert it

into the diagonal and secure it by

re-tightening the thumbscrew (3).

For 1.25" eyepieces first insert

the 2" to 1.25" adapter (4b) into

the diagonal and secure by re-

tightening the screw (3). Loosen

the adapter's screw (5) and insert

the 1.25" eyepiece(6) inside the

adapter ring, then secure it by re-

tightening the screw (5).

Focusing

Make sure the locking lever below the focuser (1) is

unlocked (position as shown in picture).

Slowly turn the focus knobs (2) one way or the other,

until the image in the eyepiece is nearly sharp.

To finely focus the image turn the 1:11 knob one way or

the other until the image is perfectly sharp (3).

Lock the screw below the focuser (1) if a heavy load is

attached (pull the lever at 90°).

The image usually has to be finely refocused over time, due

to small variations caused by temperature changes. This

often happens when the telescope has not yet reached

outside temperature.

Refocusing is almost always necessary when you change an

eyepiece.

When looking through a diagonal, the image

is inverted left to right, as an image in a

mirror. This is normal and has no incidence

for astronomical observations.

If you plan to do terrestrial observation often, like bird

watching, optional image-erecting devices such as the

Amici prism or the erected 90° diagonal may be the right

tool.

Your reseller will be glad to advise you about the best

optional part that can be used with your telescope.

Prime focus imaging with the optional field flattener

Before installing the field flattener onto the drawtube of the

focuser, the 2" ring adaptor (2) needs to be unscrewed and

removed.

In order to easily unscrew the ring, hold with one hand the ring (1)

at the end of the drawtube and then unscrew the 2" ring adaptor

(2) with the other hand.

No "universal" field flattener available on the market will deliver the premium results

achieved with the Sky-Watcher ESPRIT 120 Field flattener.

Installing the field flattener and a DSLR (Digital Single-Lens Reflex) camera

1. Screw the drawtube adaptor (1)

at the end of the focus tube.

Screw the field flattener (2)

onto the drawtube adaptor (1).

Screw the extender tube (3)

onto the field flattener (2).

Screw the enlarged 48mm T-

Ring (4) onto the extender tube

(3).

The enlarged 48mm T-

Ring may not be

included with your

telescope and should

match your DSLR

camera's manufacturer

and model. Please check

with your reseller to get

the correct 48mm

Enlarged T-Ring for

your DSLR camera.

Install your DSLR camera on

the 48mm enlarged T-Ring (4).

It guarantees excellent field flatness and ensures full illumination with extremely mini-

mized color fringing across the entire 44 mm imaging plane.

The Sky-Watcher ESPRIT 120 Field flattener is not compatible with other telescopes,

even refractors with the same aperture and same focal length.

The rings are designed to provide 75mm of back focus

with any DSLR camera. Modifications to this layout, i.e.

by adding a radial guider, will lead to blurry stars images

in the field edges.

Installing the field flattener and a CCD (Charge-Coupled Device) camera

Installing an astronomical CCD camera and its accessories (filter wheel, radial guider…) behind the

field flattener is not as straightforward as installing a DSLR camera. All DSLR cameras have the exact

same distance from the front side of the T-Ring adapter to the sensor, thus share the same extension

rings to ensure the 75mm back focus distance.

CCD cameras differ from one model to another, even in the same brand name, by the threads used and

the body-to-sensor distance. Accessories also have different possible threads and depths, thus the

combination of a CCD camera and its accessories can have any total length and any coupling thread.

A custom coupling ring is needed in order to assemble the CCD camera and its accessories (called the

"optical train") to the telescope's field flattener. The custom ring should be machined*to have:

1) A female M62x1 thread, to screw and secure the ring to the field flattener exit.

2) A thread compatible with the first component of the optical train.

3) A length to ensure that the distance from the back of the field flattener to the CCD sensor is

exactly 75mm.

The 75mm distance is measured from the edge

marking the start of the male thread on the field

flattener, to the CCD sensor (see picture on the left).

Most CCD cameras have also the distance from their

body thread to CCD sensor noted in the manual, thus

evaluating the length of the custom ring you need

can be precisely evaluated.

*Refer to your local dealer about custom ring supply.

In order to get the premium results the field flattener for

ESPRIT 120 can deliver the distance between the last

lenses to the sensor should be exactly as designed for. This

distance is called the field flattener "back focus".

Installing a 48mm filter inside the extender tube

A 48mm (2") filter can be mounted inside the DSLR

extender tube if

needed. By example using a light pollution reducer filter may allow pictures

of the night sky even in suburban areas.

1. Unscrew the closing ring at the rear part of the extender tube.

Insert the filter. Do not overtighten the filter. Put the closing ring

back in place.

This closing ring has a 48x0.75 mm thread inside, able to receive

any 48mm (2") filter.

Installing the field flattener and a CCD camera - continued

Screw the drawtube adaptor (1) at the

end of the focus tube.

Screw the field flattener (2) onto the

drawtube adaptor (1).

Screw the custom ring (3) onto the

field flattener (2).

The custom ring needs to be

sturdy enough to secure the

optical train to the field

flattener.

Screw your optical train to the custom

ring (3).

Focusing

Make sure the locking lever below the focuser (1) is

unlocked (position as shown in picture).

Slowly turn the focus knobs (2) one way or the other,

until the image in the eyepiece is nearly sharp.

To finely focus the image turn the 1:11 knob one way or

the other until the image is perfectly sharp (3).

Lock the screw below the focuser (1) if a heavy load is

attached (pull the lever at 90°).

The image usually has to be finely refocused over time, due

to small variations caused by temperature changes. This

often happens when the telescope has not yet reached

outside temperature.

Framing the picture

When the object you want to picture is in the middle of the circular 44mm field, most often its

orientation on the rectangular camera sensor is not what you expected (figure A). You can easily

reframe the picture on the camera sensor by unscrewing the blocking ring (1) at the end of the focuser

drawtube, then turning the adapter ring (2) with all the optical train until the framing suits your needs

(figure B). When done screw the ring (1) to lock position, and you are ready to picture the sky.

Andere Handbücher für ESPRIT 120 ED Super APO

Inhaltsverzeichnis

Andere SKY-WATCHER Teleskop Handbücher

SKY-WATCHER

SKY-WATCHER 767AZ1 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER CLASSIC 250P DOBSONIAN Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 15075EQ3-2 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER NEWTONIAN Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 1149EQ2 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER NEQ3 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Star Discovery 2i Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER S11670 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Star Discovery Mount Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Skyliner 200P Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 707AZ2 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 1501EQ3-2 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 909AZ3 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Saxon classic Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 1501EQ5 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER 1145EQ1 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Heritage 76 Dobsonian Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER VIRTUOSO GTi Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER AZ Tracking Bedienungsanleitung

$SKY-WATCHER Quantum 100 Refractor s11160 Bedienungsanleitung$

SKY-WATCHER

SKY-WATCHER Quantum 100 Refractor s11160 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER Black Diamond ED80 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER EQ6 Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER SK 763 EQ/TA Bedienungsanleitung

SKY-WATCHER

SKY-WATCHER LightChariot 80AR-AZ Bedienungsanleitung

Beliebte Teleskop Handbücher anderer Marken

Meade

Meade 81005 Condor Bedienungsanleitung

Celestron

Celestron NexStar 6 SE Bedienungsanleitung

Meade

Meade 114 EQ-DS Bedienungsanleitung

Celestron

Celestron C4.5 Bedienungsanleitung

Meade

Meade LX200 CLASSIC Bedienungsanleitung

Leica

Leica 82 HD Bedienungsanleitung

Celestron

Celestron CPC DELUXE 800 HD Bedienungsanleitung

EASTCOLIGHT

EASTCOLIGHT 9920 Bedienungsanleitung

zoomion

zoomion Genesis 200 EQ Bedienungsanleitung

Orion

Orion 7832 Bedienungsanleitung

Carson

Carson Skelescope SK-100 Bedienungsanleitung

Celestron

Celestron Novice 50 Bedienungsanleitung

Orion

Orion EZ Finder 7228 Bedienungsanleitung

cassini

cassini C-JRS Bedienungsanleitung

nedis

nedis SCTE5060WT Bedienungsanleitung

Meade

Meade Polaris 60EQ-D Bedienungsanleitung

PlaneWave

PlaneWave CDK700 Bedienungsanleitung

William Optics

William Optics Synta Crayford Bedienungsanleitung