SkyBell 2.0 Bedienungsanleitung
Installaion Guide
Infrared LED
(Night Vision)
Video
Camera
Main Buon
LED
Indicator
Light
Speaker
Set Screw Microphone
Moon
Sensor
Contents
SkyBell
Doorbell Device
Mounng
Plate
Special Locking Tool
Screw Anchors (2)
Wall Screws (2)
Wire Connectors (4)
(2 extra)
Tools You May Need for Installaion:
• Pliers or Crimpers
• Power Drill or Screw Driver
• Outdoor Adhesive
• Wire Strippers
SkyBell Components
S
K
Y
B
E
L
L
12
Welcome!
Thank you for becoming a member of the SkyBell
family. Please take a minute to carefully review these
instrucions so you can enjoy your SkyBell experience.
Visit our website for instrucional videos and access to
support informaion.
Installaion Videos:
www.skybell.com/support/installaion/
Support:
www.skybell.com/support/
Customer Service:
htp://service.skybell.com
1PRE-INSTALLATION CHECKLIST
1. Doorbell Chime - SkyBell is compaible with mechanical
and digital door chimes. Wireless door chimes are not
supported. Digital door chimes require an adapter, which may
be sold separately.
2. Wi-Fi Speed - Be sure you have at least 1.5 mbps
consistent upload speed at your front door. For more details on
how to check your Wi-Fi speed, visit :
www.skybell.com/support/wi-fi-speed-test.
3. Router Quality - Your SkyBell experience will only be
as good as your router. We recommend using a router
that is less than 3 years old and is manufactured by a
recognized brand. Old routers and uncommon router
brands may not be supported.
34
2POWER CONFIGURATIONS
Prior to installing your SkyBell, make sure your home is
compaible with one of the power coniguraions listed.
Power coniguraion diagrams are available at
www.skybell.com/support/power.
Unless otherwise indicated, all power coniguraions require
primary power (110/120 VAC in the US and 220/230/240 VAC,
in Europe) and a low-voltage
transformer (10-36V 10 VA).
1. A MECHANICAL DOOR CHIME AND LOW VOLTAGE
TRANSFORMER (Recommended).
2. A DIGITAL DOOR CHIME WITH ADAPTER AND A LOW
VOLTAGE TRANSFORMER.
4. Router Band - SkyBell will only connect to the 2.4 GHz
band. If you have a dual-band router, you must create unique
SSIDs for the 2.4 and 5 GHz bands. Prior to iniiaing the
syncing process, make sure your mobile device is connected to
the 2.4GHz SSID.
5. Router b/g/n - SkyBell works on the b/g network. If you
have an “N-Only” router, please acivate the b/g seing.
6. Router Channel Bandwidth - Make sure your router is
conigured to 20 MHz bandwidth.
7. Transformer - If your SkyBell is being powered by your
home’s transformer, the transformer’s output must be between
10 and 36 VAC 10 VA.
8. Accessories - For more informaion on installing an
accessory, please visit secion 4 before staring the installaion.
56
3. WITHOUT A DOOR CHIME
Setup 1:
Primary Power;
Low-voltage transformer (10-36 VAC 10 VA); and
10 Ohm/10 Wat resistor inserted between one wire from the
SkyBell and one wire from the power source
Setup 2:
12 VDC power supply; and
10 Ohm/10 Wat resistor inserted between one wire from the
SkyBell and one wire from the power source
Warning!
Installing your SkyBell with an improper power coniguraion
will automaically void your Limited Warranty
(htp://www.skybell.com/warranty).
Warning!
Coming into contact with a transformer can cause injury or loss
of life. Use extreme cauion when installing SkyBell.
OR
3INSTALLATION INSTRUCTIONS
1. To begin, press your
current doorbell buton
to make sure your exising
door chime works.
2. Remove your tradiional
doorbell and carefully detach
or cut the 2 wires currently
connected to your tradiional
doorbell.
3. Run the wires through
the center of the mouning
plate. Be sure the front side
of the mouning plate
faces you.
78
4. Secure the mouning plate to the wall with the two wall
screws. If you have stone, brick or drywall, drill holes with
the correct drill bit for your surface and use the screw
anchors to secure the screws to the wall.
Correct Drill Bit Sizes:
1. Masonry: 3/16”
2. Wood: 9/64”
3. Steel: 9/64”
Warning!
If you do not use a door chime, you must use a 10 Ohm / 10 Wat
resistor with one connecion between SkyBell and the power
source. Failure to do so could damage your device and will
automaically void your limited warranty. For more details:
www.skybell.com/support/power and www.skybell.com/legal
Instead of drilling into your wall,
you may use an outdoor adhesive
to glue the mouning plate to your
wall or door frame.
5. Gently twist together
the ends of a SkyBell wire
and a home doorbell wire
as shown.
6. Next, insert the
joined wires into a
blue wire connector
and push unil the
wires reach the end
of the wire connector.
7. With a pair of pliers, clamp down on the wire connector and
crimp the wires together.
8. Repeat steps 5-7 with the other two wires.
Either wire from your SkyBell may be
connected to either wire from your
home.
910
x3
9. Next, conirm that the LED light is on and starts to blink red.
It may take a few seconds for the blinking to start. If the light
is blinking slowly, the SkyBell’s batery is charging, which
may take up to 10 minutes to complete. If
the LED light is blinking quickly (at a
rate of once per second), the device
is charged and ready to sync.
10. The set screw is already
in place in the botom-center
hole of the mouning plate.
Place the SkyBell completely
over the mouning plate and
insert the locking tool into
the middle hole at the botom-
center of the device. Turn
the tool counter-clockwise
(right to let) 3 full rotaions. This will draw the set screw
down and lock the SkyBell into place. Be sure that the
screw is not exposed beyond the botom of the device.
11. Your SkyBell is now properly installed.
12. Before staring the syncing process, please give SkyBell
10 minutes to charge the batery.
11 12
4ACCESSORIES
Wedge Mount Accessory
The wedge mount allows you
to angle SkyBell in the direcion of
your door or visitors.
1. Remove your old doorbell chime from the wall and either
detach or cut the wires currently connected to your tradiional
doorbell.
2. Place the wedge mount so that the back of the wedge mount
faces the wall. You should see a small ridge around the circle
facing outward. Be sure that the wires are sicking through the
center hole in the wedge mount.
3. Posiion the wedge mount so that the camera will be angled in
the direcion of your visitor.
4. Place the wall mount on top of the wedge mount and posiion
so that the botom of the wall mount (the end with the set screw)
is at the center of the thinnest part of the wedge mount. Be sure
that the wires pass through the center hole in the wall mount.
5. Place two screws into the wall mount so they go through the
holes in the wedge mount. Secure the screws to the wall.
Follow the rest of the installaion instrucions on page 10.
For more support documentaion, visit:
htp://www.skybell.com/support
13 14
Door Frame Adapter Accessory
This accessory allows you to install
your SkyBell onto a door frame.
Note: your door frame should be
2.5 inches thick and a lat surface.
1. To get started, pass the wires through the center hole of your
door frame adapter.
2. Place the door frame adapter against your door frame so that
the extended porion sits lush against the outside of the door
frame. Be sure that the lip around the center hole faces you.
3. Place the wall mount directly on top of the door frame adapter
and posiion so that the botom part of the wall mount is the end
with the set screw. Be sure to pass the wires through the center
hole of the wall mount.
4. Secure the wall mount and the door frame adapter to the door
frame with the screws. Be sure that the adapter is lush and ight
against the door frame and the wall mount is level.
Follow the rest of the installaion instrucions on page 10.
For more support documentaion, visit:
htp://www.skybell.com/support
15 16
5SYNCING PROCESS
This secion will provide step-by-step instrucions for syncing
your SkyBell to your Wi-Fi router and smartphone.
What you need:
1. A compaible iOS or Android device (for a list of compaible
devices visit www.Skybell.com/support)
2. The name of your Wi-Fi network
3. Your Wi-Fi network password (if necessary)
4. The SkyBell Acivaion Code (device ID)
® ®
Register
1. Download the app from the iTunes App Store® or the Google
Play Store®. Search “SkyBell” and select our free app.
2. On the home screen of the app, tap “Register” and create an
account by entering your informaion and compleing the
account creaion process.
3. Then log out of the app by tapping the seings wheel tapping
“Sign Out”
4. Next, sign back into the app with your new account credenials.
17 18
Andere Handbücher für 2.0
1
Inhaltsverzeichnis
Andere SkyBell Gegensprechanlage Handbücher
