Skyhawk Trapmate Bedienungsanleitung

Trapmate

Installation & User Manual

Please setup and register the Skyhawk Hub BEFORE using this device!

In order to receive alerts from your Trapmate device, it must be used in conjunction with

your Skyhawk Hub (sold separately) and the Skyhawk CE smartphone app.

See the Skyhawk Hub user manual for additional information on connecting your devices.

Index:

Introduction .......................................................................................................................

Layout Summary.............................................................................................................

Installation .......................................................................................................................

Start-Up Operation ..........................................................................................................

Shut-Down Operation/Reset Operation..............................................................................

Battery Replacement .......................................................................................................

LED Indicators & Sensitivity Adjustment..........................................................................

Safety, FCC and Warranty.................................................................................................

4 - 7

8 - 11

14 - 16

18 - 19

Unpacking and Inspection:

Before you begin installation, unpack and verify you have all the correct parts.

(1) Skyhawk Trapmate

(2) AA Alkaline Batteries (pre-installed)

(1) Pull Magnet Kit

(4) Self-Stick Mounting Magnets

(8) Tacky Puddy

(1) Quickstart guide

(1) Warranty card

If you are missing any of these parts STOP, make sure you have your unit’s serial number and request a replacement

on sky-hawk.com/warranty.

In order to receive alerts from your Trapmate device, it must be used in conjunction with

your Skyhawk Hub (sold separately) and the Skyhawk CE smartphone app.

See the Skyhawk Hub user manual for additional information on connecting your devices.

Trapmate Layout Summary:

Front of Unit

LED Indicator - This multicolored LED indicator will indicate when the Trapmate is powering on or o, has

been triggered or is acknowledging a transmission. More details on the indicator colors can be found on page 17.

Function Button - This multi-use button can be used for various functions. See pages 12 and 13 for more details.

Magnet Alignment Notch - This notch shows the center alignment position of the reed switch magnet.

Mounting Cutout - This cutout can be used to mount unit with a screw or attach to a peg or hook.

Cover Screws

Function Button Mounting Cutout

LED Indicator Magnet Alignment Notch

Front of Unit (with cover removed)

LED Indicator

Mounting Pins

Battery Access (from opposite side)

Accelerometer Sensor

Mounting Pins - Once the case is opened the circuit board rests on top of four plastic mounting pins.

Accelerometer Sensor - Used to sense sudden movement or vibration of the monitored item.

Battery Access - The board can be removed to access the battery holder on the opposite side of the circuit card.

Bottom of Circuit Card (circuit card removed from case)

Battery Holder

Reed SensorFeature Jumpers

Reed Sensor - Used to sense the removal of the supplied pull magnet.

Feature Jumpers - These jumpers allow user-congurable features to be turned ON and OFF. The default

position of the jumpers is shown in the image.

Battery Holder - The battery holder accommodates 2 x AA batteries. It is required that 1.5 volt alkaline batteries

are used for expected life.

Trapmate User-Congurable Features:

The Trapmate has two feature jumpers:

Jumper #1 - Not Used

Jumper #2 - Used to enable or disable the accelerometer sensor

Accelerometer Disabled

Step 1: Open case as outlined in the Battery Replacement section of this manual and remove batteries.

Step 2: Remove circuit card from case and locate conguration header as shown below in the dashed circle.

Step 3: Move jumpers to congure settings (if dierent from the factory default settings).

Accelerometer Enabled

Step 4: Install batteries and close case as outlined in the Battery Replacement section of this manual.

Jumper #1

Jumper #2

Jumper #2 Jumper #1

Trapmate Installation:

The Trapmate can be installed using various methods including, but not limited to, the following two examples

using the supplied mounting accessories:

Method 1 : Self-Stick Mounting Magnets

Step 1: In the accessory kit, locate the four self-stick mounting magnets.

Step 2: Clean the four circular recessed areas on the back of the Trapmate with 70% isopropyl alcohol for proper

bonding of the magnets.

Step 3: Peel o the adhesive backing paper on the magnets and ax them to the circular recessed areas cleaned

in Step 2.

Step 4: The Trapmate is ready to be mounted. Make sure the area where the Trapmate will be attached is ferrous,

iron or steel.

Attach to

Iron

Steel

Prevent Falling Hazard Prevent Unit Fall Damage

Trapmate Installation:

Method 2 : Tacky Puddy

Step 1: In the accessory kit, locate the tacky puddy strip.

Step 2: Tacky puddy can be attached to the bottom or sides of the Trapmate. It is recommended that the tacky

puddy pieces are not attached to the top of the unit since that would limit visibility to the LED indicator and

function button.

Step 3: Attach to the object being monitored.

Installation - Safety Guidelines:

Make sure when placing the Trapmate on an object that it is securely attached and cannot fall o and injure some-

one or fall onto a hard surface and damage the unit.

Make sure that when placing the Trapmate that it will not interfere with other equipment.

!Tacky puddy can damage some surfaces.

Trapmate Pull-Magnet Installation:

The Trapmate is supplied with a pull-magnet kit for users who choose to use the reed switch option.

Step 1: Locate the pull-magnet kit and take out the magnet mount while setting the other items o to the side.

Step 2: On the back edge of the cover there will be small notch that shows the reed switch centering location.

Clean this area below the notch with 70% isopropyl alcohol for proper bonding of the mount.

Step 3: Peel the backing o the magnet mount and ax to rear of case as shown. The mount should be centered

on the notch and just below the seam of the top and bottom of the case.

Clean Area

Inhaltsverzeichnis

Andere Skyhawk Sicherheitssensor Handbücher

Skyhawk

Skyhawk Kiwi IR Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung