SkyLine AAA Plus Am-001 Bedienungsanleitung

Users Instructions (Draft)

AAA PLUS™ Home Intelligent Centre

Model: AM-001

www.skylinkhome.com

IMPORTANT SAFETYINSTRUCTION

SAVE THESE INSTRUCTION

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire,electric shock and injury to persons, including the

following:

1. Do not use this product near water, for example, near a bath tub, wash bowl,

kitche n sin k or laund ry tub, in a w et bas eme nt or near a sw immi ng po ol.

2. Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of

batteries in a fi re. They may explode. Check with local codes for possible special

disposal instructions.

5. Plug the adaptor to the socket-outlet that near the equipment and shall beeasily

accessible.

Certaines mesures de sécurité doivent être prises pendant I,utilisation de

matérial téléphonique afin de réduire les risques d,incendie, de choc électrique

et de blessures. En voici quelquesunes:

1. Ne pas ut iliser I,app areil près de I,eau, p.ex., Près d,une baignoire ,

d,un lavabo, d,un évier de cuisine, d

,un bac à lav er, da ns u n sou ssol

humi de ou prè s d,une piscine.

2. Éviter d,utiliser le téléphone ( sauf s,il s,agit d,un appareil sans fil )

pendant un orage électrique. Ceci peut présenter un risque de

choc électrique causé par la foudre.

3. Ne pas utiliser I,appareil téléphonique pour signaler une fuite de

gaz s,il est situé près de la fuite.

4. Utiliser seulement le cordon d,alimentation et le type de piles

indiqués dans ce manuel. Ne pas jeter les piles dans le feu: elles

peuv ent e xplo ser. Se co nfor mer a ux rè glem ents perti nent s qua nt à

I,élimination des piles.

5. La socklet-sortie sera installée près de l,éq uipement et sera

facilement accessible.

IMPORTANTES MESURES DE SÉCURITÉ

CONSERVER CES INSTRUCTION

IC Statement

''This product meets the applicable Industry Canada technical specifications.”

Before installing this equipment, users should ensure that it is permissible to be connected to the

facilities of the local telecommunications company. The equipment must also be installed using

an acceptable method of connection. In some cases, the company’s inside wiring associated

with a single line individual service may be extended by means of a certified connector assembly

(telephone extension cord). The customer should be aware that compliance with the above

conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility

designated by the supplier. Any repairs or alterations made by the user to this equipment, or

equipment malfunctions, may give the telecommunications company cause to request the user to

disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power

utility, telephone lines and internal metallic water pipe system, if present, are connected together.

This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

''The Ringer Equivalence Number is an indication of the maximum number of terminals

allowed to be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the sum of the

Ringer Equivalence Numbers of all the devices does not exceed five.''

Content

The Basics ...................................................................................................................................5

Overview ..................................................................................................................................5

Installation....................................................................................................................................6

Installing the Console ...............................................................................................................6

Program Passwords .................................................................................................................7

Program Emergency Phone Numbers......................................................................................7

Installing the Door/Window Sensor ..........................................................................................9

Installing the Motion Sensor ...................................................................................................10

Battery notes for the System ..................................................................................................10

Alarm & Alert Mode....................................................................................................................11

Alert mode..................................................................................................................................11

Mute .......................................................................................................................................11

System Status ........................................................................................................................12

Arm Mode ..................................................................................................................................13

Arming the System .................................................................................................................13

Disarming the system.............................................................................................................13

Disarming a triggered control panel........................................................................................14

Disarming under Duress.........................................................................................................14

Panic ......................................................................................................................................14

Receiving an emergency call .....................................................................................................15

Home Automation ......................................................................................................................13

Receiver Model SW-100R ......................................................................................................13

Communication ......................................................................................................................16

Remote Operation by Telephone ...........................................................................................16

To access the control panel away from home ........................................................................17

Advanced Programming.............................................................................................................17

Learn Sensor..........................................................................................................................18

Sensor Location Selection Guide ...........................................................................................18

Learn Sensor – continue ........................................................................................................19

Learn Remote / Receiver........................................................................................................20

Zone Dependent Setting – Beep / Alarm................................................................................21

Zone Dependent Setting – Auto Mute ....................................................................................22

Zone Dependent Setting – Event Trigger ...............................................................................22

Zone Dependent Setting – Alert Zone ....................................................................................23

Erase Sensor..........................................................................................................................24

Erase Remotes / Receiver......................................................................................................25

Wallmount Installation ………………………………………………………………………………..25

FCC Information ………………………………………………………………………………………..29

Accessories …………………………………………………………………………………………….30

The Basics

Overview

Congratulations on your purchase of Skylink wireless security system, Model AM-001. This is a

complete wireless system which not only functions as a security system, but also monitors your

premises by giving you alert notification when the system is not armed. It is also a home

automation center, which allows you to remotely control household appliances and lightings,

even you are away from home. AM-001 can be controlled by dialing in from any touch tone

phone, which makes it even more convenient and powerful. Additional accessories such as

different kinds of sensor and controller can be added to suit your specific needs. This user’s

instructions will guide you through the whole setup procedure as well as all the programming

instructions. Please follow the instructions closely, you should find it very easy to setup the

system.

Door / Window

Sensor x 2

Motion

Sensor

Consol

Keychain

Remote

In the package, you should find the following items:

•One Control Panel

•One Motion Sensor

•Two Door / Window Sensors

•One Keychain Remote

•One AC adapter

•One telephone cord

•Batteries for all sensors

•Four AAA backup batteries for Control Panel

•Mounting hardware

Installation

Installing the Console

You must first determine where the control panel will be located. Please follow the criteria

below to select the ideal location for the control panel.

-Place it within few feet of an electrical outlet and phone jack

-Place it where it is easily accessible by you and other users

-Place it away from any doors or windows which could be accessed by non-intended

users

-Place it away from extreme temperature sources such as oven, stove and away from

large metal objects which could affect the wireless performance

After you have selected a location for the control panel, you are now ready to connect all the

necessary wires and ready to power up the unit.

1. Connect the phone line from the telephone jack to the back of the control panel where it

marks “Line”.

2. If you have another telephone that will be using the same telephone jack, you may connect

this telephone to the control panel by plugging in the phone cord to the “Phone” outlet on the

control panel.

3. Remove the battery cover on the bottom of the control panel with a Phillips screwdriver, and

insert 4 AAA alkaline batteries into the batteries holder. All the LED will flash once, and you

will hear 3 beeps. PWR LED will be on indicating the control panel is powered properly.

4. Plug in the AC adapter to the nearby electrical outlet and plug the other end to the socket on

back of the control panel.

5. Rotate the antenna to the upright position to ensure the best signal reception.

Program Passwords

Master Password can be used for programming, arming, disarming the system, and telephone

access. The default Master Password is [1234].

Secondary Password can be used for arming, disarming the system, and telephone access.

Secondary Password cannot be used for programming. The default Secondary Password is

[0000].

Duress Password is used when you are forcibly compelled to disarm the control panel. You

may enter the Duress Password. Entering the duress password will stop the siren from

sounding but the control panel will silently call the emergency phone numbers for help. The

default Duress Password is [3838]. You should definitely change this password and let all the

users know this password.

In order to change the password, follow the procedures below.

1. Press the PROG button on the side of the control panel, the [PROG] LED will be on..

2. Enter the current Master Password, [1234]. Enter [2], which represents Password

Programming.

3. Select the type of password you would like to change:

•Enter [1] for Master Password,

•Enter [2] for Secondary Password

•asswordEnter [3] for Duress P

4. Enter new 4-digit password.

5. Enter new 4-digit password again, password accepted.

Program Emergency Phone Numbers

You can program up to 5 Emergency Phone Numbers. When the system is in panic situation,

he control panel will call 5 phone numbers and announce its statust

ide of the control panel, the [PROG] LED will be on.1. Press the PROG button on the right s

2. Enter the current Master Password.

3. Enter [1], which represents Phone Number Programming.

4. Select the phone memory from 1 to 5. Note: In an emergency, the control panel will call

phone memory 1 as the first number, then phone memory 2 will be called, then memory 3, 4,

and 5. So it is recommended to program most important phone number in phone memory 1.

[Do not program police, 911 or fire station phone numbers into the control panel.]

5. Enter the phone number then press [Arm]. Note: You may enter a 3-second pause by

pressing [Mute] if needed. The phone number can be up to 29-digit long, including multiple

pause periods.

6. After entering the phone number, enter how many times you want the phone number to be

called, from 1 to 9 times. Press ARM to confirm.

7. After entering the redial, enter how many times you want the emergency message to be

played, from 1 to 9 times. It is recommended to play the message at least 2 times. Press

ARM, phone accepted.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST

CALLS TO EMERGENCY NUMBERS:

1) Remain on the line and briefly explain to the dispatcher the reason for the call.

2) Perform such activities in the off-peak hours, such as early morning or late evenings.

Caution - To ensure proper operation, this equipment must be installed according to the

enclosed installation instructions. To verify that the equipment is operating properly and can

successfully report an alarm, this equipment must be tested immediately after installation, and

periodically thereafter, according to the enclosed test instructions.

Attention

This product is not an alarm system providing facilities to summon assistance, for use

by persons who can be considered to be living at risk. This product is not intended to for

use in health care signaling equipment or directly connect to central-station (Police,

Medical, Fire).

Installing the Door/Window Sensor

Window / Door Sensor is used to monitor doors or windows that open and close. When these

doors / windows are open or closed, the sensors will transmit a signal to the control panel to

notify the user. These sensors consist of 2 parts, one is the transmitter, the other is the magnet.

Remove the top cover of the sensor and insert the 3V lithium

battery to the sensor.

The transmitters should be

mounted on the door frame or

window frame by double sided

tape. The magnet should be

mounted on the door or window

by either double sided tape or

screws.

Make sure the arrow on the

magnet is aligned with the grey

marking on the transmitter.

(Show picture)

If the surface of the frame is flat enough, double-sided foam

tape is sufficient, otherwise, it is recommended to use the

mounting plate and screws as well. After mounting the

sensor, put the cover back on with the Houselink logo in the

upright position.

Try to mount the sensors as far away from the floor as possible to avoid damaging them.

Mounting the sensors at a higher position will also result in better operating range.

Do not mount the sensor to the exterior of the door / window, always mount the sensor to the

interior side of the door / window to avoid being damaged or stolen by non-intended users.

Testing: Open the door or window to trigger the sensor, the main unit will then alert you by

visual/audio indication and voice cue.

Installing the Motion Sensor

The motion sensor is most suitable for guarding the bedrooms. Use the motion sensor to

monitor the passage leading to the bedrooms or hallway.

You needed to power up the sensor first. Undo the

screw on the back of the motion sensor and remove

the cover of the battery compartment. Connect a

9V alkaline battery to the connector wire.

If you are going to install the motion sensor outdoor,

please change the sensitivity to low by changing the

sensitivity jumper from HI to LOW. You also needed

to change that zone to an Alert Zone. (Refer to p.

XX)

Then close the battery cover and re-insert the screw.

Mount the ball-head joint on the wall with screws provided. Slide the

back of the sensor into the ball-head joint. The mounting angle can be

adjusted.

Keep sensors within 30m (100 ft) of Control Panel.

Walk in the detected area. If the motion is detected, a read light inside the sensor will glow. If

the red light does not glow, motion has not been detected and you should re-position the sensor.

Repeated this procedure until your motion is detected. There should be no movement in the

detected area during the 20 seconds.

Note: When installing the motion sensor, avoid placing it near heat or cold producing devices

(i.e. A/C or furnace vents, fans, ovens, space heaters, etc). Air movement, especially caused by

changes in temperature may trigger the Motion Sensor and cause false alarms. Please

carefully test your Motion Sensor so that it will only be triggered by people.

Battery notes for the System

When you are reminded by the system that any sensors are in low battery, please change the

battery accordingly. The sensors, keychain remotes and accessories are generally designed to

have a battery life of around one year. Since there are large variations in different working

environment, we suggest replace new batteries every nine months.

The alkaline batteries in the main unit are expected to use as back up purpose in normal

working condition. We suggest you replace the alkaline batteries every nine months after you

have installed new batteries or right after a shortage of electricity in your premises.

Inhaltsverzeichnis

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung