SkyLink MD-318 Guide Bedienungsanleitung

1. INTRODUCTION

ON/OFF/Dimming Control

MD-318

Model MD-318

Thank you for your purchase of a SkylinkHome ON/OFF/Dimming

Control Model MD-318. This ON/OFF/Dimming Control allows you to

wirelessly turn on and off, dim and brighten connected lights with the

SkylinkHome lighting transmitters.

The ON/OFF/Dimming Control MD-318 can communicate with up to

8 transmitters, so user has the option to add more transmitters to the

system, such as more remote controls, or motion sensors etc.

All wireless signal communications within the SkylinkHome System are

based on rolling code technology to ensure highest security is used.

The following items are included in this package:

- ON/OFF/Dimming Control

- Screws and Accessories

- User’s Instructions

2. INSTALLATION

1. Turn off power to the circuit that you plan on installing the ON/OFF/

Dimming Control to at the circuit breaker.

WARNING

Failure to turn off power at the circuit breaker can result in electrical

shock causing severe or fatal injury.

Note: Lighting Load

The ON/OFF/Dimming Control is designed to operate incandescent light

or dimmable compact fluorescent light with a maximum load of 300W at

120VAC. Light bulbs must be dimmable in order to achieve dimming

function.

2. Follow the diagrams below to install the ON/OFF/Dimming Control

with the 3 wires: Neutral, Live and Load. The grey antenna should not

be cut or connected to anything else.

3. After all the wires are connected, ensure that all of the wire connectors

are attached securely and there should be no exposed copper wiring.

Straighten the antenna after installation.

4. Secure the MD-318 to a flat surface by 2 screws or you may place it

inside the lighting fixture.

5. Turn the circuit breaker back on and turn on the wall switch that is

used to operate this lighting fixture.

6. After you hear a single beep, the ON/OFF/Dimming Control is installed

properly and you can start programming transmitters to the ON/OFF/

Dimming Control .

Note:

Antenna (grey wire) - Do not cut it, keep it as straight as possible after

installation.

3. PROGRAMMING TRANSMITTERS

In order to operate the ON/OFF/Dimming Control remotely, a transmitter

must be programmed to the ON/OFF/Dimming Control. Each ON/OFF/

Dimming Control can be operated by up to 8 different transmitters (or 8

different command signals).

To program a transmitter into the ON/OFF/Dimming Control, follow the

instructions below.

You will also need the instructions from the transmitter.

1. The ON/OFF/Dimming Control should be powered off initially. This can

be done by switching off the wall switch or circuit breaker controlling

the ON/OFF/Dimming Control.

2. Power on the ON/OFF/Dimming Control by switching on the wall switch

or circuit breaker. You will hear a beep from the On/Off/Dimming

Control. The beep indicates the ON/OFF/Dimming Control is now in

programming mode and it will stay in this mode for 15 seconds.

3. Transmit a "Learn" code from the transmitter. Refer to the manual of

the transmitter to transmit this "Learn" code.

4. Once the transmitter is programmed, the ON/OFF/Dimming Control

will beep, indicating you have successfully programmed the transmitter

to the ON/OFF/Dimming Control. Now the programmed transmitter is

ready to be used.

Note: To program other transmitters/sensors (besides TC transmitter),

please refer to the instructions of those transmitters/sensors and the

above instructions.

CAUTION

Installation is required and enclosed instructions must be followed

carefully to all steps and notes. If you are uncertain or uncomfortable

performing this installation, please consult a qualified electrician.

This manual should also be retained for future reference. 4. OPERATING MODES

The ON/OFF/Dimming Control can control the light in 2 different

operating modes.

1) On / Off Mode - Allows operating the light either on and off, without

dimming function.

2) Dimming Mode - Allows operating the light in on, off or dimming

(dim / brighten). Light must be either incandescent light or dimmable

compact fluorescent light.

The factory default operating mode is on/off mode. However, if your light

is dimmable, you may change the operating mode to Dimming Mode. To

change the operating modes, please follow the instructions below.

1. Turn on the light by activating the programmed transmitter.

2. Press and hold a button on the transmitter (TC series, TM series,

TD series, TB series) that is programmed to the module for 10 seconds.

3. The light will flash. If it flashes once, that means it is in On / Off Mode.

If the light flashes twice, that means it is in Dimming Mode.

4. Repeating step 2 above will toggle the setting between On / Off Mode

and Dimming Mode.

Note: When used with an optional Motion Sensor ID-318, this ON/OFF/

Dimming Control can operate under countdown timer mode.

5. OPERATION

Screws and Accessories

Before Installation

Live

(Usually Black)

Live

(Usually

Black)

Neutral

(Usually White)

Neutral

(Usually

White)

(White)

Antenna

(Red)

Load

(Black)

After Installation

WARNING

Non-dimmable load has to be always working under ON/OFF mode.

Using non-dimmable load under dimming mode may damage the

non-dimmable CFL.

Note:

If the ON/OFF/Dimming Control is

installed after a wall switch, you can

use the transmitter to operate the

light remotely only if the wall switch

is in the ON position. If the wall

switch is off, no power is provided

to the ON/OFF/Dimming Control

and therefore, it cannot operate the

light.

OFF

Remote

Works

Remote Does

Not Work

5. OPERATION (CONT)

This receiver offers two optional states after powered on, choose the one

which fits your requirement.

1. Power On - Light On:

1) You may use the wall switch to control the light as usual. When the

wall switch is off, the light is off. When the wall switch is on, the light is

on.

2) After a power outage and the electricity comes back, the light will be

on if the wall switch is in On position.

2. Power On - Light Off:

1) A special sequence is needed to turn on the light by the wall switch.

To turn on the light by the wall switch: 1) Switch On, 2) Switch Off,

3) Switch On again within 2 seconds. Light will be on.

2) After a power outage and electricity comes back, the light will be off

under most of the circumstances.

To toggle a receiver between these two states, re-program a transmitter

twice consecutively to the receiver. Referring to Section 3, repeat the

programming steps twice consecutively with a transmitter that is already

programmed, the receiver will change state.

Input Voltage: 120VAC , 60Hz

Maximum Load: 300W at 120VAC

Operating Frequency: 318MHz

Range: Up to 500 feet in open area

Standby Current: 6mA

Minimum Load: 10W

Operational Temperature: -4° F - 140° F (-20° C - 60° C)

Humidity: 5%-95%

7. TECHNICAL SPECIFICATIONS

6. ERASING TRANSMITTERS FROM THE

ON/OFF/DIMMING CONTROL

8. FCC

The Remote Control is approved by the FCC and it complies with Part 15 of the

FCC Rules. Its operation is subject to the following two conditions :

1. This device may not cause harmful interference.

2. This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible

of compliance could void the user’s authority to operate the equipment.

9. WARRANTY

If, within one year from date of purchase, this product should become defective

(except battery), due to faulty workmanship or materials, it will be repaired or

replaced, without charge. Proof of purchase and a Return Authorization are required.

You may erase a transmitter from the ON/OFF/Dimming Control, but you

cannot erase a specific device directly, you must erase all the wireless

devices, then program the ones you want to keep. Follow the instructions

below to erase programmed transmitters.

1. Power off the lighting receiver. (Switch off the wall switch)

2. Transmit a "Erase" code from the transmitter until step 4.

3. Power up the ON/OFF/Dimming Control (Switch on the wall switch),

you will hear a beep.

4. You may stop the "Erase" code signal transmission, the ON/OFF/

Dimming Control will beep, indicating you have successfully erased all

the devices from the ON/OFF/Dimming Control.

To erase other transmitters / sensors, please refer to the instructions of

the transmitters / sensors.

11. ACCESSORIES

The Skylink System consists of many other devices such as

SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall

Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF

Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,

ON/OFF Control, Smart Button Garage Door Control, etc. Please visit

Skylink website at www.skylinkhome.com for more information.

Home

10. CUSTOMER SERVICE

If you would like to

·find out the up-to-date specifications

·know more about features and applications

·download documents, i.e. user’s instructions

·order Skylink products

or if you have difficulty getting products to work, please:

1. visit our FAQ section at www.skylinkhome.com, or

2. email us at [email protected], or

3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.

Fax (800) 286-1320

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3

Email:[email protected]

http://www.skylinkhome.com

P/N. 101Z699

Patent Pending

In case the transmitter is not on hand, you can still operate the lighting

fixture with the wall switch.

Dieses Handbuch passt für folgende Modelle

Andere SkyLink Controller Handbücher

SkyLink

SkyLink MM-318 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung