Skyrc OSPERY Bedienungsanleitung
FPV RACER
OSPERY
Instruction Manual
[Version 1.0]
Dynamic Rotor Tilting Quadcopter
INTRODUCTION
FPV Camera Len
Brushless Motor
Propeller
Antenna
Canopy
LED Light
Congratulations on your choice of the SkyRC OSPERY FPV Racer. This is a high performance
quadcopter with FPV camera, video transmitter and remote controller.
OSPERY FPV Racer features a very unique frame with a unique DMT (Dynamic Motor Tilting)
capabilities. With your elevator controls offers instant high speed shoot out and solid air braking.
DRT also offering instant and clear cornering. You can clear sharpest corners easily with tight
solid turns that will surely leave your competitors behind on the track. And DRT gives you more
forward view without tilting your camera up. When motors tilt, you get instant speed with little
tilting and you retain much more forward view at higher speeds. Comparatively at same speed,
other pilots will be looking at grounds only and getting slapped by the trees, while OSPERY pilots
will dodge everything with a beautiful precision due to better forward views.
Let’s meet your OSPERY FPV Racer now.
Please review the illustrations below for a full list of your OSPERY FPV Racer parts.
Servo
Receiver
Battery
Compartment
· 01 OSPERY FPV RACER
Left Stick Right Stick
Power ButtonPower Button
Switch A
Mounting Point
Capacitive Touch
Screen
INTRODUCTION
Remote Controller
For more information about the remote controller, please download user manual from following link.
http://www.flysky-cn.com/download_detail/downloadsId=33.html
Switch B
Switch D
Switch C
02 ·
OSPERY FPV RACER
Remote Control
In the Package
L Wrench
6040 Propeller x 8
Main Body
Socket Screw x 4
Antenna
· 03 OSPERY FPV RACER
Things You’ll Need
3S LiPo Battery LiPo Battery Charger
FPV Monitor HD FPV Goggle
or
ATTENTION BEFORE FLIGHT
The OSPERY FPV racer is recomended for piolts, 14 years or older, with RC hobby experience.
Only fly the OSPERY FPV racer in dry weather, with low wind, please do not fly in rain or heavy
foggy conditions.
Always choose large open fields for flying. Check local LAW and ordinances for legal flying areas.
Always keep at least 10 feet (3 meters) distance to the aircraft when armed, to avoid injury from high-
speed propellers on the ground or while flying. Always disarm before handeling the aircraft.
Do not fly close to high-voltage power lines, cellphone towers, or radio towers, as these may disrupt
your control signal.
ALWAYS check local laws BEFORE flying. NEVER fly over crowds, concerts or sports stadiums.
Attention before flight
(Purchase Separately)
04 ·
OSPERY FPV RACER
3. Setting Frequencies
5.740GHz 5.760GHz 5.780GHz 5.800GHz
5.820GHz 5.840GHz 5.860GHz 5.880GHz
5.725GHz 5.745GHz 5.765GHz 5.785GHz
5.805GHz 5.825GHz 5.845GHz 5.865GHz
5.733GHz 5.752GHz 5.771GHz 5.790GHz
5.809GHz 5.828GHz 5.847GHz 5.866GHz
5.705GHz 5.685GHz 5.665GHz 5.645GHz
5.885GHz 5.905GHz 5.925GHz 5.945GHz
BAND A BAND B
BAND E BAND F
One button for frequency selection
method is easy and intuitive.
Frequency Selection: Single push to change frequency,
push and hold for 2 seconds to change band.
Actual Frequency number will be display on the monitor or
goggle through OSD.
A video receiving equipment is needed (such as SkyRC FPV
monitor, FPV Goggle etc.) to display an image and OSD
information.
5.658GHz 5.695GHz 5.732GHz 5.769GHz
BAND R
5.806GHz 5.843GHz 5.880GHz 5.917GHz
1 2 3
ON
ASSEMBLE
Assemble
1. Install Mushroom Antenna
Put the battery into the drone, adjust the
drone’s center of gravity, so the head and tail
are in the same horizontal line, after adjusted,
fix the battery with velcro.
2. Battery Installation
· 05 OSPERY FPV RACER
To attach the propellers correctly, you need match the spin direction on the motors with the
propellers.
Hold the motor in place with one hand, then using L-Wrench and turn in opposite direction to
secure the propeller.
5. Attaching Propellers
CD
Silver Nut
A B
Silver Nut
Black Nut
Black Nut
L-Wrench
123
ON
RGB LED Board comes with six RGB5050 LEDs & Dip Switches. The color of LED
can be set by Dip Switches. Seven colors are selectable by change ON/OFF of the Dip
Switches.
Color
Green
Red
Blue
Magenta
Cyan
Yellow
White
Dip Switches
1
(Green) 2
(Red) 3
(Blue)
ON
OFF
OFF
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
OFF
ON
RGB5050 LEDsDip Switch
4. Setting Color of RGB Led Board
ASSEMBLE
06 ·
OSPERY FPV RACER
READY FOR FLIGHT
Place the aircraft in a wide open space,
with the rear facing you.
(This position) is known as “TAIL IN”
Put all the function switches to the UP position, put all trims and dials to the MIDDLE
position, move the throttle to the lowest position. Press two power button simultaneously
to turn on the Remote Controller. To turn off Remote Controller, press two power button
simultaneously again.
READY FOR FLIGHT
Attention:
You will hear Beep~... sound. Put switch C to lower position for Dynamic Motor Tilting.
Dynamic Motor Tilting Mode
For the normal flight mode, put the switch C to middle position.
Put the aircraft on a horizontal place and connect the
aircraft power, then the rear LED light turn on.
(Make sure positive and negative connected correctly)
1.
2.
3.
4.
Front
Rear
Switch C
· 07 OSPERY FPV RACER
MOTOR UNLOCK / LOCK
Throttle stick on the right
Throttle/Rudder stick ELEV stick
Throttle stick on the left
Throttle/Rudder stick ELEV stick
After binding the remote controller with the OSPERY FPV racer, Gently push the throttle stick down and
move the rudder (YAW) stick to the right side and hold for more than 2 seconds to unlock the motors.
LED inside the body will turn GREEN.
Be very careful at this point, as pushing the throttle up will start the motors.
You can test by pushing the stick up a little, the motors should start.
Motor Unlock
Motor Unlock / Lock
Motor lock
Lock the motors by moving the throttle stick all the way down and the rudder (YAW) stick all the way to
the left. GREEN LED will turn off.
TEST: Push the throttle stick up a little, the motors will not start when locked.
NOTICE: The motors are LOCKED by default after successful binding.
The OSPERY FPV racer have a low-voltage alarm beeper.
And the OSD give you a visual reference for the remaining battery power.
When voltage reach below 10.2 volts the RIGHT LED light will flash and the beeper will
sound alarm.
WARNING: Do not hesitate to land when you hear the alarm or see the OSD
indicating 10.2 volts.
08 ·
OSPERY FPV RACER
Flying upwards or downwards
Yawing
(rotating towards left or right)
Pitching
(moving onwards or backwards)
Rolling
(turning towards left or right)
up
down
123
ON
123
ON
123
ON
This section explains how to control the orientation of the Drone through the remote controller.
Controlling Drone Movement
CONTROLLING DRONE MOVEMENT
FPV Racer
Battery Voltage
Working Current
Maximum Tilt Angle
Flying Time
Flying Distance
Propeller
Working Temperature
Storage Temperature
Working Humidity
Storage Humidity
3S LiPo
12A x 4 Max.
45°Max
7 minutes
<300metre
Three-blade 5045
0-40℃
-10- 50℃
10-90% RH
20-65% RH
· 09 OSPERY FPV RACER
The open source flight controller firmware that we chose to power the OSPERY is Baseflight,
mainly due to the code is stable, mature and proven to work.
Because Baseflight is constantly evolving, you will get the most updated setup instructions from
their website.
Hardware is shipped with the most current firmware at the time of assembly. It is recommended
to upgrade to latest stable or development firmware for new features.
Latest baseflight firmware (development)
https://github.com/multiwii/baseflight
To hook up the Baseflight configurator, hook up a personal computer via a standard micro-USB
cable, to the connector on the right side of the OSPERY FPV Racer.
SETUP OSPERY
SETUP OSPERY & SPECIFICATIONS
USB Port
SPECIFICATIONS
Inhaltsverzeichnis
Andere Skyrc Drohne Handbücher
