Sliger SV590 Bedienungsanleitung
SV590
Manual V1.0
SCREWS
The SV590 comes with a total of 5 different screws types. For the purposes of
this guide we will assign a unique color and type number to each of the screw
to signify their locations in this guide.
GREEN- M3 x 6mm PAN HEAD
Securing PCIe Cards
PINK - M3 x 8mm FLAT HEAD
Power Cord
RED - M3 x 5mm FLAT HEAD
Radiator Mount Bracket
Power Cord Mount Bracket
SSD / HDD bracket
VIOLET –632 x ¼” TRUSS HEAD
Motherboard
Power Supplies
Orange –632 x ¼” FLAT HEAD
Side Panels
Base Plate
Radiators
HDDs
EASY OFF TOP
The top cover features tool-less removal via ball-stud mounting points,
this allows for convenient access to your motherboard and PCIe card IO
ports in place of traditional front panel IO ports. The top panel may be very
tight on the first few times on/off.
SIDE PANELS
GPU SIDE REAR CORNER
CPU SIDE FRONT CORNER
Side panels of the SV590 are held on via 8x 632 x ¼” FLAT HEAD screws.
Four per side, two at top and two at bottom.
Please pay attention to the correct size screw driver as to not strip the screw
heads.
SLIDE OFF PANELS
Once the screws are removed, the front/GPU side panel slides of the front,
and the rear/CPU side panel slides off the back of the case.
Panels may scratch the case frame, please handle with care.
CASE FRAME
The rear radiator bracket of the SV590 frame is held on by 6x M3 x 5mm
FLAT HEAD screws; 3x per side, 2x at top and one at bottom.
You will also need to unscrew the SSD mount bracket which is held on by
additional 2x M3 x 5mm FLAT HEAD screws.
FRAME SEPARATION
POWER CORD
The SV590 includes an internal
power cord extension, and a
mount bracket for easy access to
the extension plug.
There is also a pass-through
grommet to get the extension
into the case. Clip this grommet
over the cord, then run the cord
through the cutout, and slide the
grommet into position as shown
left.
The power cord extension is then installed into the mount bracket with two
M3 x 8mm FLAT HEAD screws.
Once the power cord is installed both into the bracket and into the
grommet, the bracket then can be attached to the case via 2x M3 x 5mm
FLAT HEAD screws.
Note that the SV590 power cord
mount is adjustable to four
different positions in order to
allow the user to position it where
it obstructs the motherboard IO
ports the least.
It is critical you install the
power cord before installing
the IO shield for your
motherboard!
POWER SUPPLY
The fan on the power supply is recommended to be positioned with the fan
side of the power supply towards the center spine of the case. This
orientation will result in better overall system temperatures and lower noise.
Once positioned, the SFX PSU can be attached to the PSU Mounting Bracket
with up to 6x of the included 632 x ¼” TRUSS HEAD screws.
Note that not all SFX Power Supplies have all 6x screw holes as shown.
MOTHERBOARD
Don’t forget to install the power
cord and your IO shield first!
Some CPU coolers may require a
back plate installed before
installing the motherboard into
the case.
It is advised to also check that any
back of motherboard M.2 drives
are installed before mounting the
motherboard.
Once the IO shield and power
cord / power cord grommet are
properly installed the
motherboard can now be
mounted using 4x 632 x ¼”
TRUSS HEAD screws.
A Phillips #2 screw driver with a
minimum 7-8cm shaft length is
recommended for installing these
screws. Both of the screws on the
PCIe slot side of the motherboard
have pass-through holes in the
case frame to allow the screw
driver and screw to pass through
and be screwed in straight
Additional installation instructions
for your CPU, CPU cooler, RAM,
etc. are covered by your
motherboard or coolers
respective user manual
Andere Handbücher für SV590
2
Inhaltsverzeichnis
