Smacq Technologies USB-5200 Series Bedienungsanleitung

USB-5200 Series Multifunctional

Data Acquisition Devices

User Manual

Rev. C

Beijing Smacq Technology Co., Ltd.

Smacq.com

Smacq.cn

竺

macq.

Smacq

Statement

No content of this manual may be reproduced, modified or abridged without prior

consent and written permission.

Trademark information

Smacq is a registered trademark of Beijing Smacq Technology Co., Ltd The

names of the other products and companies mentioned in this document are

trademarks or trade names of their respective companies.

Other Disclaimer

1 |

If you have any questions or need assistance in using this product or this

document, please contact us via:

Phone:(+86)10-52482802

E-Mail: [email protected]

Website: http://www.smacq.com

http://www.smacq.cn

The information provided in this document may be modified and updated in

subsequent versions without prior notice.

Smacq does not provide any warranties, express or implied, for this document

as well as the information inside it, including but not limited to implied

warranties of the marketable nature of the product and its suitability for a

particular purpose.

There may be a chance that inaccurate descriptions or errors exist in this

document. Smacq does not hold any liability for accidents because of the

information and deductive functions provided in this manual, as well as the

resulting loss of any chance because of the use of this document.

Smacq reserves the rights to change product specifications, prices, and decide

whether to stop the production.

2 |

Safety Requirements

Warning

Only the voltage within the specified range can be connected.

Voltage exceeding the specified range may cause damage to the

device, and even present a negative impact on personal safety.

Check the product specification for detailed reference to the range

of voltages that can be connected by each port.

Do not attempt to operate the device in other ways that are not

mentioned in this document. Incorrect use of the device may be

dangerous. In the event of device damage, the internal security

protection mechanism will also be affected.

Do not attempt to replace device components or change devices

in other ways that are not mentioned in this document. Do not

repair the device yourself in the event of a product failure.

Do not use the device in an environment where an explosion may

occur or where flammable flue or gas is present. If you must use

the device in this kind of environment, please fit it into a proper

case.

While the device is running, all chassis covers and fill panels need

to be closed.

For equipment with exhaust vents, do not insert foreign objects

into the vents or block air circulation in the vents.

3 |

Measurement Categories

Warning For use in measurement category I (CAT I) only. Do not use in

measurement category II/III/IV. Use this device to connect

signals or make measurements.

Measurement categories Note

Measurement categories I (CAT I) means that measurements are made on a circuit that

is not directly connected to the main power supply. For example, a circuit that is not

exported from the main power supply, especially a circuit that is exported from a

protected (internal) primary power supply, is measured. In the latter case, the

instantaneous stress will change. Therefore, the user should be aware of the

instantaneous affordability of the device.

Measurement categories II (CAT II) means that measurements are made on a circuit

that is directly connected to a low-voltage device. For example, a measurement on

household appliances, portable tools and similar equipment.

Measurement categories III (CAT III) means that measurements are made in

construction equipment. For example, a measurement on the distribution boards, circuit

breakers, wiring (including cables, Busbars, junction boxes, switches, sockets) in fixed

equipment and equipment for industrial use and certain other equipment (for example,

fixed motors that are permanently connected to fixtures).

Measurement categories IV (CAT IV) means that measurements are made on the source

of low-voltage equipment. For example, a measurement on a meter, a major overcurrent

protection device, and a pulse control unit.

Environment

Temperature

Operating 0℃~ 55℃

Storage -40℃~ 85℃

Humidity

Operating 5%RH ~ 95%RH, no condensation

Storage 5%RH ~ 95%RH, no condensation

Pollution degree 2

Highest elevation 2000 m

4 |

Some of the substances contained in this product may be harmful

to the environment or human health. In order to avoid releasing

harmful substances into the environment or endangering human

health, it is recommended that appropriate methods be used to

recover this product to ensure that most materials can be properly

reused or recycled. For information about processing or recycling,

please contact your local professional organizations.

Pollution degree description

Pollution degree 1: No pollution, or only dry non-conductive pollution. This pollution

degree has no effect. For example: a clean room or an air-conditioned office

environment.

Pollution degree 2: Generally only dry non-conductive pollution occurs. Temporary

conduction can sometimes occur due to condensation. For example: General indoor

environment.

Pollution degree 3: Conductive pollution occurs, or dry non-conductive pollution becomes

conductive due to condensation. For example, an outdoor sheltered environment.

Pollution degree 4: Permanent conductive pollution caused by conductive dust, rain, or

snow. For example: Outdoor places.

Recycle precautions

Warning

5 |

CONTENT

STATEMENT.............................................................................................................. 1

SAFETY REQUIREMENTS........................................................................................... 2

MEASUREMENT CATEGORIES................................................................................... 3

ENVIRONMENT......................................................................................................... 3

1. GETTING STARTED............................................................................................. 7

1.1. PRODUCT INTRODUCTION..................................................................................7

1.2. FUNCTION DIAGRAM..........................................................................................8

1.3. PRODUCT SPECIFICATIONS................................................................................8

1.4. PRODUCT UNPACKING.......................................................................................11

PRECAUTIONS..........................................................................................................11

CHECK THE PACKING LIST........................................................................................11

2. INSTALLATION................................................................................................. 12

2.1. CONNECTOR SIGNAL PINS DISTRIBUTION.........................................................12

2.2. USB CABLE REINFORCEMENT DESIGN................................................................13

2.3. DRIVER INSTALLATION.....................................................................................14

3. ANALOG INPUT (AI)..........................................................................................15

3.1. CIRCUIT DIAGRAM.............................................................................................16

3.2. SIGNAL CONNECTION METHODS........................................................................16

3.3. SIGNAL ACQUISITION MODE.............................................................................16

HARDWARE TIMING MODE.......................................................................................16

CONTINUOUS ACQUISITION MODE.......................................................................... 16

LIMITED NUMBER ACQUISITION MODE.................................................................... 17

AI SAMPLING CLOCK..........................................................................................17

3.5. TRIGGER.......................................................................................................... 18

CLEAR TRIGGER.......................................................................................................18

PRE-TRIGGER...........................................................................................................18

4. DIGITAL INPUT (DI)...........................................................................................20

4.1. SIGNAL ACQUISITION MODE............................................................................. 20

HARDWARE TIMING................................................................................................. 20

CONTINUOUS ACQUISITION MODE........................................................................... 20

LIMITED NUMBER ACQUISITION MODE.....................................................................20

4.2. SAMPLING RATE................................................................................................21

4.3. DI SAMPLING CLOCK..........................................................................................21

4.4. TRIGGER...........................................................................................................21

CLEAR TRIGGER .......................................................................................................22

PRE-TRIGGER..........................................................................................................22

5. DIGITAL OUTPUT (DO）.................................................................................... 24

5.1. SIGNAL OUTPUT MODE......................................................................................24

3.4.

6 |

IMMEDIATE OUTPUT................................................................................................ 24

HARDWARE TIMING................................................................................................. 24

FINITE NUMBER OUTPUT MODE ............................................................................... 24

INFINITE LOOP OUTPUT MODE................................................................................. 25

INFINITE NON-LOOP OUTPUT MODE........................................................................ 25

5.2. OUTPUT UPDATE RATE..................................................................................... 25

5.3. DO SAMPLING CLOCK........................................................................................ 25

5.4. TRIGGER.......................................................................................................... 26

CLEAR TRIGGER ....................................................................................................... 27

6. SYNCHRONIZATION SYSTEM............................................................................ 28

6.1. SAMPLING CLOCK ............................................................................................. 28

6.2. EXTERNAL TRIGGER.......................................................................................... 28

7. SERVICE AND WARRANTY.................................................................................30

8. ORDERING INFORMATION................................................................................31

7 |

1. Getting Started

This chapter describes the basic functions of USB-5200 Series Data Acquisition Device,

as well as product specifications and precautions in the process of product unpacking.

1.1. Product introduction

USB-5200 Series data acquisition device is the multifunctional data acquisition device based

on high-speed USB2.0 interface. When connected to the computer, it can be used for

continuous high-speed signal acquisition and high-speed control signal output.

USB-5200 series of data acquisition devices can measure analog and digital signals

continuously and save the data to the computer hard drive without interruption. It can also

provide digital signal output, periodic repetitive signal output, and high-speed

uninterrupted non-repetitive signal output controlled by a computer.

USB-5200 series data acquisition device supports operating in Windows OS, providing

standard DLLs and support for mainstream development languages including VC++, VB, C#,

LabVIEW, and MATLAB.

USB-5200 series data acquisition device provides multiple models, in terms of function and

performance. For detailed reference, please turn to Chapter 1.3 for specification

description of each model.

Key Features

High speed USB interface, Plug and Play, USB powered

16-bit analog input resolution, support continuous uninterrupted acquisition

The analog input supports up to 16 channels of synchronous sampling and up

to 500kS/s/Ch sampling rate.

Up to 10MS/s/Ch sampling rate for digital I/O

8 |

1.2. Function Diagram

Figure 1.1 shows the schematic diagram of USB-5200 series data acquisition device.

Digital system

USB bus

Trigger source:

Software trigger

External trigger

Din trigger

Sampling clock source:

Internal module sampling

clock source

External sampling clock

source

Digital I/O

FIFI cache

Figure 1.1 USB-5200 series data acquisition device functions

1.3. Product specifications

The following product specification parameters, unless otherwise stated, are acquired at

the temperature of 25°C and the humidity of 40%, while the device is turned on for 20

minutes.

Analog input

Number of channels

USB-5220/5221: 16Single-Ended

USB-5210/5211: 8Single-Ended

USB-5620/5621: 16Single-Ended

USB-5610/5611: 8Single-Ended

USB-5420/5421: 8Single-Ended

USB-5410/5411: 8Single-Ended

ADC type SAR

Resolution USB-5220/5221/5210/5211: 16-bit

USB-5620/5621/5610/5611: 14-bit

9 |

USB-5420/5421/5410/5411：12-bit

Highest sampling rate

USB-5211/5221: 500

USB-5210/5220: 250

USB-5611/5621: 500

USB-5610/5620: 250

USB-5411/5421: 500

kS/s/Ch,continuous

USB-5410/5420: 250kS/s/Ch,continuous

Timing resolution 10ns

Channel synchronization Yes

Range ±10 V / ±5V

Input coupling mode DC

Input impedance 100 MΩ

Small signal bandwidth

（-3 dB）

Input bias current 1uA

Analog input

max voltage ±1 5 V

Software FIFO 2 MPts/Ch

Pre-trigger FIFO 4096 Pts

AI capture mode Continuous acquisition mode and limited number acquisition mode

Analog input accuracy (with temperature coefficient of 5 ppm/℃)

Range Gain error

(ppm of reading)

Offset error

(ppm of range)

Random noise

（μVrms）

Full range

absolute accuracy

（μV）

±10 V90 4180 1100

±5 V80 10 90 500

Digital I/O

Number of channels USB-5210/5211/5610/5611/5410/5411: 8 input,8 output

USB-5220/5221/5620/5621/5420/5421: 2 input,2 output

Ground reference DGND

10 kΩ

Digital input pull-up

resistanc

Digital input voltage High level:1.95 V~5 V

Low level:0 V~1.2 V

Digital output voltage High level:3.3 V

Low level:0 V~0.003 V

Low level

Digital output

power-on status

10 MS/s/Ch

450 kHz

DIN highest

sampling rate

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smacq Technologies Lagerung Handbücher

Smacq Technologies

Smacq Technologies PCI-1132 Bedienungsanleitung

Smacq Technologies

Smacq Technologies USB-3100 Series Bedienungsanleitung

Smacq Technologies

Smacq Technologies PCI-1255 Bedienungsanleitung

Smacq Technologies

Smacq Technologies USB-3200 Series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung