SmallRig MagicFIZ Bedienungsanleitung
- User Manual -
MagicFIZ Wireless Follow Focus System
Kits and Accessories
MagicFIZ Wireless Follow Focus Basic Kit
ID: 3781
MagicFIZ Wireless Follow Focus Handgrip Kit
ID: 3782
Follow Focus Marking Disk (Wooden)
ID: 4091
USB-C to D-Tap Cable
ID: 3266
USB-C to DC Cable
ID: 3268
MagicFIZ Wireless Follow Focus Two Motor Kit
ID: 3918
Foreword
Warnings
Intended Use
1
1
2
2
2
2
7
7
7
7
7
7
4
4
4
9
9
3
3
3
3
6
6
6
5
5
5
8
8
8
10
10
11
11
12
13
1
Thank you for purchasing SmallRig's product.
In order to ensure user's safety and prevent the product damages caused by any improper use,
please carefully read the “Warnings” below and properly keep this User Manual for future
reference.
Please do not disassemble the product or change its battery. If you have any question,
please contact the seller to apply after-sales service.
Please read this User Manual carefully.
Do not use the product in water because it is not dust or water proof.
Do not let the product fall to the ground, be hit or suffer violent impact.
Never remove the non-detachable lithium battery without permission.
Since there are some hazardous substances in the battery, please do not discard it. Instead,
dispose of the product that is damaged or will never be used according to the waste
management measures.
When the battery is not in use for a long time, please charge and discharge the battery each
6-month, and provide it with approximately 60% of the electric quantity to prolong its use life.
Please read this User Manual carefully, especially the “Warnings”.
Please use or store the product in the environment mentioned herein.
It will be regarded as an improper use when the users are not correctly follow the user manual
or use the product under the specific working condition.
Product Function Description
ID: 3918
Wireless Handwheel Controller
Wireless Handgrip
Electronic Controller Module
Wireless Receiver Motor
Battery Plate
Handgrip Adapter
Shoulder Rig Adapter
Monitor Adapter
Φ15mm Rod
Rod Clamp with NATO Rail
Snap-on Follow Focus Gear Ring
USB-C to USB-C Cable
Spanner
User Manual
Carrying Bag
× 1
× 1
× 1
× 2
× 2
× 1
× 1
× 1
× 1
× 1
× 2
× 1
× 1
× 1
× 1
× 1
In the Box
ID: 3781
Wireless Handwheel Controller
Wireless Receiver Motor
Battery Plate
Handgrip Adapter
Φ15mm Rod
Rod Clamp with NATO Rail
Snap-on Follow Focus Gear Ring
USB-C to USB-C Cable
Spanner
User Manual
Carrying Bag
Follow Focus Marking Disk (Silicone)
Follow Focus Marking Disk (Silicone)
× 1
× 1
× 1
× 1
× 1
× 1
× 2
× 1
× 1
× 1
× 1
× 1
ID: 3782
Electronic Controller Module
Wireless Receiver Motor
Wireless Handgrip
Battery Plate
Handgrip Adapter
Φ15mm Rod
Rod Clamp with NATO Rail
Snap-on Follow Focus Gear Ring
USB-C to USB-C Cable
Spanner
User Manual
Carrying Bag
× 1
× 1
× 1
× 1
× 1
× 1
× 1
× 2
× 1
× 1
× 1
× 1
1. Wireless Handwheel Controller
REC Button: 1. REC Recording ON / OFF Function; 2. Machine ON / OFF Function.
MARK Button: 1. A-B Marks; 2. Automatic Lens Calibration.
Up / Down Button: 1. Channel Adjustment; 2. Motor Number Adjustment; 3. Page Up / Page Down.
SET Button: 1. Press and hold the button to enter or exit the current option;
2. Click the button to activate or confirm the current option.
LOCK Button: For preventing misoperation; turn on/off the switch by double click.
Knob 1 (K1): Fine control of Wireless Receiver Motor.
OLED Screen
Indicator
REC Button
MARK Button
Marking Disk
Knob 1 (K1)
Up Button
Down Button
SET Button
LOCK Button
Contact Port
USB-C Port
Bottom Cover
Extension Port
1 1
2
2
2
3
3
34
4
5
5
6
6
7
7
8
8
4
5
6
7
89
9
10
10
12
13
11
11
2
Indicator: Six color display, including red - green - blue - yellow - pink - white.
USB-C Port: Charging and wired communication port.
Contact Port: Charging and communication port.
Extension Port: 1/4"-20 threaded hole.
Marking Disk: Replaceable.
2.Wireless Handgrip
3. Wireless Follow Focus Controller Kit
(Combination of Wireless Handgrip + Electronic Controller Module)
* The Electronic Controller Module can be used only with the Wireless Handgrip.
Electronic Controller Module
USB-C Port:
1. Charging and discharging; 2. Communication.
Indicator:
Battery level and status display.
Button:
Click to show current battery level.
Safety Lock: For preventing accidental falling off.
REC Button:
1. REC Recording ON / OFF Function;
2. Machine ON / OFF Function;
3. Confirm.
Up / Down Button:
1. Channel Adjustment;
2. Motor Number Adjustment;
3. Page Up / Page Down.
Knob2 (K2):
Control Wireless Receiver Motor.
Extension Port:
For connecting with external accessories.
Battery Compartment:
Suitable for LP-E6 battery.
Hanging Hole: For assembling lanyard.
USB-C Port
Indicator Safety Lock
Batte Compament
Knob 2 (K2)
Hanging Hole
Button
Extension Port
Extension Po
Down Button
Display Up Button
REC Button
3
4. Wireless Receiver Motor
OLED Screen
φ15mm Rod Opening
M0.8 Gear
REC Port
Port
Battery Plate Port
Up / Down Button: 1. Channel Adjustment; 2. Motor Number Adjustment.
REC Port: Connect the camera REC port for wired control.
Port: Power supply and communication Port.
Battery Plate Port: Used with Battery Plate (ID: 3777), compatible with NP-F batteries.
Instruction of Product Installation and Power Supply
1. Installation Guide for Wireless Receiver Motor
Install the Wireless Receiver Motor on
the camera side by use of the included
accessories.
①
②
③④
Handgrip Adapter
Up Button
Down Button
2. Installation Guide for Wireless Handwheel Controller
2.1 Install the Wireless Handwheel Controller on the camera side by
use of the Handgrip Adapter via 1/4"-20 threaded hole.
2.2 Marking Disk Replacement / Installation.
Align with the
slot for installation
4
USB-C to D-Tap Cable
DC 5521
4.1 Use the USB-C to D-Tap Cable (ID: 3266) or USB-C to DC Cable (ID: 3268) to connect the
V-mount battery for powering the Wireless Receiver Motor
Wireless Receiver
Motor Port indication
Safety lock is in locking
3. Installtion Guide for Wireless Handgrip
4. Instruction for Wireless Receiver Motor Power Supply
3.1 Combined Installation of Electronic Controller Module, Wireless Handwheel Controller, and
Wireless Handgrip.
3.2 The Wireless Handgrip is suitable for both left and right hands.
3.3 Installation Guide for Shoulder Rig Adapter,
VCT-14 Extension Arm, and ARRI Rosette
Handgrip AdapterLeft hand holding Right hand holding
Shoulder Rig Adapter Wrench Reinforce
5
Wireless Receiver Motor
Port indication
4.2 Use the standard USB-C to USB-C cable to connect the Wireless Handgrip for powering the
Wireless Receiver Motor, achieving the cabled control.
4.3 Power the Wireless Receiver Motor through the Battery Plate.
5.1 Connect one end of the control cable with the Wireless Receiver Motor and the other end with
the camera; wirelessly control the video REC recording through the
Wireless Handwheel Controller and Electronic Controller Module.
Wired control and power
supply of the Wireless Handgrip
Wired Control of the
Wireless Handwheel Controller
Powered by the Battery Plate
Compatible with NP-F batteries
Wireless Receiver
Motor REC Port
REC
5. Instruction for REC Wiring
Sony Z CAMPanasonic
FUJIFILM
A7, A7R, A7S, A7II, A7RII, A7SII, A7SIII,
FX3, A7III, A7RIII, A7IV, A7R IV, A9, A9 II,
A5100, A6000, A6100, A6300, A6400,
A6500, A6600, RX100 III, RX100IV,
RX100V, RX100 VI, RX100 VII
ID: 2971 ID: 3325ID: 2970
X-T3, X-T4,
X-T20, X-T30
S5, S1, S1R, S1H,
BS1H, GH4, GH5,
GH5S, GH6, G9,
G95
E2, M4, S6
BGH1(Panasonic)
6
Interface Instruction
Instruction of
Motor Interface
Instruction for Wireless Handwheel
Controller Interface (single control)
Instruction for Electronic Controller Module Interface
Disconnected
Status
Wireless
Status
Wired
Status
Channels
Motor Number
Input Voltage
Motor Position
Battery Status
Safety Lock
Channels
Motor Number
Status of A Mark
and B Mark
Motor Position
Communication
Status
REC Prompt
Power-on Status
Channels
Motor Number
Status of A Mark
and B Mark
Motor Position
Communication Status
5.2 Directly connect the Wireless Handwheel Controller and Electronic Controller Module with the
camera BLE to wirelessly control the REC recording.
Sony NikonCanon
A7C, A7RⅢ, A7RIV, A7 IV, FX3,
A7SⅢ, A9, A9 II, RX100 Ⅶ,
DSC-RX100M7, A6100,
A6400, A6600, ZV1, ZV-E10
Z50
EOS 90D, EOS M6 Mark II
EOS M50, EOS R, EOS R5
EOS RP, G7X Mark III
7
Basic Operation
1. ON / OFF Operation
Instruction for Wireless Handwheel
Controller Interface (double controls)
Press and hold the UP / DOWN button to
turn on the machine; press both buttons
simultaneously to turn off the machine.
Press and hold the REC button
to turn ON / OFF the machine.
Wireless
Handwheel
Controller
Control Bar
Wireless
Handgrip
Control Bar
REC
UP Button
Down Button
2. Channel Adjustment
3. Motor Number Adjustment
F15
567
F15
567
Double click / of the Wireless Receiver Motor / Wireless Handwheel Controller /
Electronic Controller Module to select the channel.
432
000 999
999
NUMBER
Wireless Receiver Motor: Press and hold to activate the motor number;
click / to adjust the number; press and hold to exit.
8
[Note]
The motor can be controlled only
with same channel and motor
number.
F15
567
432 999
999 999
Electronic Controller Module Handgrip Mode: Press and hold to activate the motor
number; click / to adjust the number; press and hold to exit.
Wireless Handwheel Controller Single-Display Mode: Click SET " " to activate the motor
number; click / to adjust the number; press and hold SET " " to exit.
999
4. Lens Calibration (automatic / manual)
Method 1-1: Automatic lens calibration with the Wireless Handwheel Controller
[Note]
For double-display mode, it can identify
the available motor number;
For single-display mode, it can identify
the current motor number.
999
999 999
Mark
Confirm
Press and hold MARK " " to start the calibration; click / to adjust the motor number.
9
Wireless Handwheel Controller Double-Display Mode: Click SET " " to activate the motor
number and switch the control; click / to adjust the number; press and hold "SET" to exit.
Inhaltsverzeichnis
Andere SmallRig Kamerazubehör Handbücher
