Smart-MAIC D101 Bedienungsanleitung

Version 5.0

USER GUIDE

smart-MAIC D101

Measure, Analyze,

Improve and Control,

.... be smart!

USER MANUAL

CONTENT

I. Introduction ....................................... 3

Purpose of the device and its functions ............. 3

Controlled output .................................. 3

Location of device components ..................... 4

Device status indicator ............................. 4

II. Getting Started .................................... 5

Installation and connection......................... 5

III. Connection diagram ................................ 6

IV. Data check ......................................... 8

V. Connecting to your wireless network ............... 9

VI. Reboot and recovery factory settings . ............. 11

VII. Maintaining your device ........................... 11

VIII. MQTT Service ..................................... 12

IX. Terms and Conditions ............................. 13

X. Scope of delivery .................................. 15

XI. Specifications ..................................... 15

XII. Access to data. Visualization ...................... 15

Purpose of the device and its functions

The device is designed for continuous measurement of electrical

network parameters and electricity consumption.

The device measures the following parameters:

• voltage, V

• current strength, A

• active power, W

• reverse * active power, rW

• active energy, Wh

• reverse * active energy, rWh

• Power factor

• temperature,°С/°F

* parameters are available in the extended version of the device

Communication with the device is carried out via the IEEE 802.11

Wi-Fi2.4GHzwirelesscommunicationprotocol.

The device transfers the accumulated data to the "cloud" server

forfurtheranalysisandvisualization.Formoreinformationabout

the processing capabilities of the data received from the device,

see the WEB page www.smart-maic.com.

Current data is also available on the built-in WEB site of the

device.

Controlled output

The device is equipped with a controlled dry contact output.

The controlled output is intended for automation of load control.

The output can control power solid-state relays to which

electrical appliances are connected, or for building automation in

low-current networks.

The output is controlled remotely, on the device's WEB page or

from the server. It is also possible to control the output according

topredefinedconditionsand/orschedule.

The controlled output is intended for switching power loads no

more than 50W.

Thank you for purchasing the smart-MAIC 101 Energy Monitor.

This device allows you to measure and record changes in electricity

consumption and parameters of a single-phase power grid.

I. INTRODUCTION

Location of device components

The device is made in a housing for installation on a DIN rail with

an IP20 protection level. When installing at the monitoring object,

it is necessary to use a mounting box made of plastic with a level

of dust and moisture protection IP54 for indoor installation or IP65

for outdoor installation. For outdoor installations, avoid direct

sunlight.

The figure shows the main components of the device.

Top view

Device status indicator

The device status indicator is located on the front panel. The

indicator signals the following device states:

Indicator state Device status

Indicator

flashing quickly

search is performed and

wireless network connection

Indicator

flashing slowly

the built-in access point is activated,

it is possible to connect to the device

to configure the parameters

Indicator

burns constantly

device connected

to the wireless network

Indicator does not work - the device is turned off, or

- defective or

- indicator is off in settings

1 Upper group

of contacts for

connecting current

transformers

2 Reset button

3 Bottom group

of contacts for

connecting power

4 Device status

indicator

USER MANUAL

Installation and connection

The device can be installed in an electrical panel on a DIN rail.

Followthestepsbelowtoinstallthedevice:

1. Mount the device on a DIN rail.

2. Secure the device by sliding the latch up.

The connection of the device to the mains must be carried out by

trained personnel with a permit of at least group III for electrical

safety when working on installations up to 1000 V.

Depending on the configuration, the device can be supplied with

different types of transformers:

• Type 1 - transformer ring, connected to contacts 3-4 of the

device

• Type 2 - split transformer, connected to slot 5 of the device.

To connect the device, run next steps:

1. Connect the leads of the current transformer to the device

according to the wiring diagram. If your transformer is

equipped with a quick plug, do not connect it to a running

device. Connecting a transformer plug to a working device may

damage the device.

2. Slide the current transformer over the phase conductor.

Current transformers have an energy direction indicator. It

is accepted that the energy moves in the direction from the

electricity meter towards the consumers. Installing the current

transformer in accordance with the energy direction indicators

will give the best measurement accuracy.

3. Connect the phase and neutralwiresto the device in accordance

with the connection diagram.

II. GETTING STARTED

III. CONNECTION DIAGRAMS

A WARNING:

Do not put unconnected current

transformers on the wire. This can damage

the transformers.

6USER MANUAL

Upper contact group

1 controlled output

2 controlled output

3 current transformer, red wire

4 current transformer, black wire

5 socket for detachable

current transformer

Lower contact group

6 zero

7 phase

Fornormaloperationofthedevice,itisnecessary,intheplaceof

its installation, to provide a good signal of your wireless network

with Internet access. At the first start-up or after a short press on

the Reset button, the device switches to the wireless access point

mode.

V. CONNECTION TO YOUR WIRELESS NETWORK

On your computer or phone, go to the list of wireless networks

and select the smart-MAIC0123456789 network connection. If the

“smart-MAIC” + network (your device number) is absent, briefly

pressthe Reset button on your device. There is no default password

for connection.

After successful connection, enter http://192.168.4.1 in the

address bar of the browser and go to the built-in WEB site of the

device.

In the "WiFi and Network" section, select your network name

from the list of wireless networks, click the "Connect" button and

enter your network password.

If the name (SSID) of your network is missing in the list ofwireless

networks, refresh the list by clicking the "Refresh" button.

Wait a minute and reconnect to the device's access point again.

Reload the device settings page and make sure that the connection

is successful and the device's internal IP address is in the status

bar.

Disconnectfromthedevice'shotspotandconnecttoyourWiFi

network. Go to the built-in WEB site of the device using the IP

address obtained upon connection and continue configuring the

parameters.

IfyoustillhavequestionsaboutconnectingtoaWi-Finetwork,

see the article on our portal >> link

If you are having difficulty finding a device on your network, use

the search utility.

GeneraltipsifyouarehavingproblemsconnectingtoWiFi:

1. For stable operation, the signal level must be greater than

-80dB, i.e. better than -70dB.

2.TrychangingtheWiFitypeto"G(upto54Mbs)"inthedevice

settings.

3. Try changing the channel on your router.

4. Try connecting the device to a different router to diagnose the

problem.

The default password is 0000, preventing you from connecting

devices to your cloud server account.

The password must consist no more than 10 digits in length.

Your new password will allow you to access data from your device

stored on the "cloud server".

In the "Device Config" section, select the language of the WEB

interface convenient for you.

Change the password for entering the WEB interface of the

device.

USER MANUAL

In the "Server Config" section, check the connection of the device

to the "cloud" server.

In the "About" section, look at and copy the device ID for yourself.

You will need the device ID to connect the device to the "cloud

server".

Go to the device page in the "Current Data" section and check the

correctness of the readings. If the connection is correct, the Power

Factor[PF]parametershouldtendto1.00.Alsocheckthelogicand

correctness of the connection if you see the word Revers

IV. DATACHECKING

VI. RESETANDRESTOREFACTORYSETTINGS

To restore the factory settings, you must use the Reset button.

The Reset button is located near the top group of contacts. It has

two functions:

1. Reboot the device - briefly press the Reset button. After

pressing the Reset button, the device will reboot and enter the

wireless access point mode.

2. Restoring factory settings - press and hold the Reset button

for more than 5 seconds. After restoring to factory settings,

the device will reboot and enter wireless access point mode.

Connect to your wireless network and configure the machine

according to Chapter 3 “Connecting to a wireless network” and

“Configuring settings”.

Factoryresetdoesnotaffectenergystoragemeters.

The wireless access point mode will turn off automatically 15

minutes after the end of work with the WEB interface of the device.

The device does not require periodic maintenance.

A built-in CR 2032 3V battery is used to power the device clock.

The battery installed in the device has a long service life - more

than 10 years. Battery life is greatly affected by the temperature

conditions in which the device is used.

In the event of a complete battery failure, the device will continue

to operate with limited functionality.

VII.MAINTENANCEOFTHEDEVICE

Tosynchronizethe accumulativemeter[Wh]Energyand[rWh]

Rev.Energy with the readings of your electric meter, set the initial

values for the accumulated data in the device settings in the

“Current Data” section, note that the device measures electricity in

watts, therefore, the kilowatts of your meter need multiply by 1000

to get watts. If your meter displays only the total consumption

figure for three phases at once, then you can simply divide this

value by three.

To control the “dry contact” output, you must activate this feature

on the device's WEB interface in the “MQTT Server” section. The

output state is changed by publishing a control phrase to the

<device number> .SETOUT topic.

The device supports data transmission and dry contact output

control using the Message Queue Telemetry Transport (MQTT)

service.

You can activate the MQTT service on the device's WEB interface

in the "MQTT Server" section.

If the fields "Username" and "Password" are left blank, then the

Only non-encrypted connection to the MQTT server is supported.

The device periodically publishes data in the format <device

number>. <Topic name> to the following topics:

n – phase number

(1-3)

* parameters are

available in the

advanced version of

the device

Topic

name

Data Description

V+n volts voltage, V

A+n amperes current strength, A

W+n watts active power, W

rW+n watts reverse* active power, rW

Wh+n watts* hour stored energy

rWh+n watts* hour reverse* accumulated energy

KWh+n kilowatts* hour accumulated energy

rKWh+n kilowatts* hour return* accumulated energy

PF+n PowerFactor PowerFactorpowerfactor

Temp °С/°F Temperature

OUT 0-1 Output state

JSON FormatJSON All data in JSON format

VIII. MQTT Service

Replacing the battery is carried out in the following sequence:

1. Disconnect the device from the power supply.

2. Unscrew the 4 screws connecting the device body

and remove the upper case.

3. Remove the old battery from the holder.

4. Observing the polarity, insert a new battery into the holder.

5. Put on the upper part of the case and tighten the 4 screws.

USER MANUAL

Inhaltsverzeichnis

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

smart-MAIC D101 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken