Smart power NPMCARD Bedienungsanleitung

V1.2 –Rev.09-21

User’s Manual

The Network Power Management Card

allows a UPS/iPCS system and

environmental sensor to be managed,

monitored, and configured.

Network Power Management Card

NPMCARD

TABLE OF CONTENTS

Introduction......................................................................................................................................1

Installation Guide.............................................................................................................................4

Web Interface...................................................................................................................................8

Reset to Factory Default Setting / Recover from a Lost Password ................................................31

NPMCARD Firmware Upgrade......................................................................................................32

Save and Restore Configuration Settings......................................................................................33

Troubleshooting.............................................................................................................................34

Conformance Approvals ................................................................................................................35

Appendix 1: IP Address Identification for Smart Power Systems Network Power Management Card

.......................................................................................................................................................33

Introduction

Overview

The Smart Power Systems Network Power Management Card allows for remote monitoring and

management of a UPS/iPCS attached to a network. After installing the hardware and configuring an

IP address, the user can access, monitor, and control the UPS/iPCS from anywhere in the world!

Simply use a web browser, NMS to access your UPS/iPCS. Servers and workstations can be

protected by the UPS/iPCS utilizing Smart PowerMaster Enterprise Clients to gracefully shutdown

when signaled by the Network Power Management Card.

Features

Real time UPS/iPCS monitoring

Remote management and configuration of the UPS/iPCS via Web Browser, NMS

Local management and configuration of the UPS/iPCS via serial connection

Trigger servers/workstations to shutdown during a power event to prevent data loss or corruption

Schedule shutdown/start-up/reboot of the UPS/iPCS remotely

Event logging to trace UPS/iPCS operational history

Graphic data logging to analyze power conditions

Save and restore configuration settings including current UPS/iPCS and ATS parameter

configuration.

Event notifications via Email, SNMP traps

Support IPv4/v6, SNMPv1/v3, HTTP/HTTPs, DHCP, NTP, DNS, SMTP, SSH, Telnet, FTP

protocol.

Support Email Secure Authentication Protocols: SSL, TLS

Support External Authentication Protocols: RADIUS

SNMP MIB available for free download

User upgradeable firmware via FTP

Quick installation

Hot-swappable

Support Environmental Sensor

System Requirements

A 10/100Mbps Ethernet connection to an existing network

Web Browser or SSH client

(Optional) NMS (Network Management System) compliant with SNMP

Smart Power Systems Network Power Management System

Application with Smart PowerMaster Enterprise

Unpacking

Inspect the Network Power Management Card upon receipt.

The package should contain the following:

Smart Power Systems Network Power Management Card

Quick Start Guide

Spare Jumper

Smart Power Systems Network Power Management System

Front Panel

NPMCARD

LED Status Indicators

Link LED

Condition

Off

The Network Power Management Card is not connected to the

Network/ or the Network Power Management Card power is off

On (Yellow)

The Network Power Management Card is connected to the Network

Tx/Rx LED

Off

The Network Power Management Card power is off

On (Green)

The Network Power Management Card power is on

Flashing (Green)

- Receiving/transmitting data packet

- Reset finished

1. Universal Port

2. Ethernet Port

3. Tx/Rx Indicator

4. Link Indicator

Smart Power Systems Network Power Management System

Installation Guide

Step 1. Hardware Installation

Note: The Smart Power Systems Network Power Management Card is hot-swappable, so you do

not need to turn off the UPS/iPCS to install it.

1. Remove the two retaining screws from the expansion slot and remove the cover.

2. Install the Smart Power Systems Network Power Management Card into the expansion slot.

3. Insert and tighten the retaining screws.

4. Connect an Ethernet cable to the Ethernet port of the Smart Power Systems Network Power

Management Card.

5. (Optional) To connect an environmental sensor, use a RJ45 Ethernet cable. Connect one end to

the Universal port on the NPMCARD and the other end into the sensor. For more information,

please see the environmental sensor user’s manual.

NPMCARD

Smart Power Systems Network Power Management System

Step 2. Configure the IP address for the Smart Power Systems Network Power Management

Card

Method 1: Using the Power Device Network Utility

1. Install the Power Device Network Utility available for download at:

https://www.smartpowersystems.com/downloads/Power-Device-Network-Utility/universal-pdnu151-setup.exe

2. After installation completes, run the “Power Device Network Utility”.

3. The main window of the Power Device Network Utility program is shown in Figure 1. The

configuration tool will display all Smart Power Systems Network Power Management Card

devices present on the local network subnet. The "Refresh" button is used to search the local

network subnet again.

Figure 1. The main window of the “Power Device Network Utility” program.

4. Select the Network Power Management Card you are setting up. Click on the Tools menu and

select “Device Setup” or double click the device you want to configure.

5. You can modify the IP Address, Subnet Mask, and Gateway address for the Device MAC Address

listed in the Device Network Settings window, as shown in Figure 2. The factory default IP

Address is 192.168.20.177 and the default Subnet Mask is 255.255.255.0.

Figure 2. The Device Network setting window.

Smart Power Systems Network Power Management System

6. Modify the IP, subnet mask or gateway address. Enter the new addresses into the

corresponding fields and then click “Save”.

7. You will need to enter a User Name and Password for the Network Power Management Card in

the authentication window, as shown in Figure 3.

- Default user name: admin

- Default password: password

Figure 3. Authentication window.

8. If the IP address change is successful, you will see a message confirming the IP set up is OK, as

shown in Figure 4.

Figure 4. Setup IP Address successfully message.

9. In case the change is not successful, for example, if the IP address change is unsuccessful you

will see a warning message. Attempt to make the desired changes again. If the problem

persists please see the Troubleshooting section for help.

Smart Power Systems Network Power Management System

Method 2: Using a command prompt

1. Obtain the MAC address from the label on the Network Power Management Card. Each

Management Card has a unique MAC address.

Note: The MAC address is labelled on the card.

2. Use the ARP command to set the IP address.

Example:

To assign the IP Address 192.168.10.134 for the Network Power Management Card, which has a

MAC address of 00-0C-15-00-FF-99 you will type in the following in the command prompt from a

PC connected to the same network as the Network Power Management Card.

(1) Type in “arp -s 192.168.10.134 00-0C-15-00-FF-99” for Windows OS; type in ”arp –s

192.168.10.134 00:0c:15:00:ff:99” for Mac OS, then press Enter.

3. Use the Ping command to assign a size of 123 bytes to the IP.

(1) Type in “ping 192.168.10.134 -l 123” then press Enter.

(2) If the replies are received, your computer can communicate with the IP address.

To select an available IP address for the Network Power Management Card, please refer to

Appendix 1.

Smart Power Systems Network Power Management System

Web Interface

You will need to enter a User Name and Password to login to the interface, and can select a

preferred language after login. There are two user account types.

1. Administrator

- Default user name: admin

- Default password: password

2. View only

- Default username: device

- Default password: device

The administrator can access all functions, including enable/disable the view only account. The

viewer can access read only features but cannot change any settings.

Note: 1. The Administrator account is also used for the FTP login and Power Device Network

Utility.

2. Only one user can log in and access the device at a time.

Web Content

Note: English is the default language and you can change to a preferred language.

[Summary] Provide an overview of the system operation and the items that are auto refreshed;

however, different UPS system models may have different items displayed.

Item

Definition

Current Condition

Display the current operating condition of the UPS and

environmental sensor.

UPS Status

Battery Capacity

Graph of the percentage of the current UPS battery capacity.

Load

Graph of the load of UPS as a percentage of available Watts.

Remaining Runtime

Length of time the UPS can support its load on battery power.

System Data

Name

The name given to the UPS.

Location

Location description given to the UPS.

Contact

The person to contact about this UPS.

Uptime.

Length of time the system has been working continuously

Envir Status

Temperature

Graph of the current temperature reading of the environmental

sensor.

Humidity

Graph of the current humidity reading of the environmental sensor.

Inhaltsverzeichnis

Andere Smart power Stromversorgung Handbücher

Smart power

Smart power DSS1500RT-TBF Gebrauchs- und Pflegehandbuch

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung