Smartswitch STS-220 Handbuch

Smartswitch Toilet Controller

Model: STS-220

The unique Deluxe Programmable Toilet Controller by Smartswitch was designed for all

electric marine toilets with remote, fresh or salt water flushing supply via an inlet pump or

water solenoid valve. The stylish control panel provides fully automatic programmed

flushing when the Flush touch pad is pressed. It also provides independent operation of

the inlet or discharge pumps for maintenance or line clearance when the manual touch

pads are used. In-built troubleshooting features and toilet pump protection are standard.

This Product has been Factory Preset to operate effectively without

making any further adjustments.

Should you wish to alter these settings please follow proceeding

instructions.

If the tank system is

connected, this light will

turn on when the Holding

Tank is full and disable

any further flush cycles.

The extraction motor

will run while the

button is held down.

(Max 20 seconds)

Water will be added

while the button is

held down.

(Max 20 seconds)

When pressed the

system will activate

a complete flush

cycle automatically.

Programming

This product has three Model Modes of operations:

Model Mode 1 = Standard Mode

Model Mode 2 = Tecma Silence (Series)

Model Mode 3 = Tecma Prestige (Series)

Model Mode 4 = European Mode

This product has been factory default set to Model Mode 2 (see page 4)

Factory Default: T1 = 20 seconds Model Mode = Tecma Silence (Series)

Please Note: If you have a Tecma Silent (Series) Toilet System ALWAYS choose Model

Mode 2.

Should you wish to change these settings then proceed as below.

Advisory Warning: 1.5 litres per flush is the recommended minimum flush setting for

discharge lines of less than 6 feet. Dilution is the secret to efficient waste transfer,

through pipes and must be considered when programming your controller. Increase your

flush volume appropriately if the discharge line is greater than 6 feet in length.

Note –Variations in controllers may substitute the following buttons: Flush =

Normal Flush, Fill = Water Only, Empty = Empty Only.

Programmable Time Options (Actuate to 0.1%)

Timer T1 & T2 (Water Valve/Pump) & (Extraction Motor) from 1 to 20 seconds.

Timer T3 (Water Valve/Pump) is programmable from 0 to 20 seconds.

This manual applies to units manufactured after 01/08/2012

Programming for Standard Model Mode 1

Step 1 –Placing the unit in program mode:

After wiring and applying power, hold the Water Only & Empty Only buttons down

together for 3 seconds. The Holding Tank Full LED will give three quick flashes

indicating you have entered program mode. You may now release both buttons.

Once in program mode you can now program one of the following three timers: T1 =

Water Valve/Inlet Pump, T2 = Discharge Pump or T3 = Water Valve/Inlet Pump.

Step 1 will need to be repeated for each of these delay times.

Setting T1 Water Valve/Inlet Pump Time:

After placing the unit in program mode, as in Step 1 above,press the Normal Flush

button the number of times required for the Water Valve/Inlet Pump time (one press = 1

second, two = 2 sec’s, etc). The Tank LED will flash once indicating a valid key press.

Note: If the button is pressed 21 times it will start back at 1 second.

Once this is done press the Empty Only button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Setting T2 Discharge Pump Time:

After placing the unit in program mode, as in Step 1 above,press the Empty Only

button the number of times required for the Discharge Pump time (one press = 1 second,

two = 2 sec’s, etc). The Tank LED will flash once indicating a valid key press. Note: If the

button is pressed 21 times it will start back at 1 second.

Once this is done press the Normal Flush button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Setting T3 Water Valve/Inlet Pump Time:

After placing the unit in program mode, as in Step 1 above, press the Water Only button

the number of times required for the Water Valve/Inlet Pump time (one press = 0 sec’s,

two = 1 second, three = 2 sec’s, etc). The Tank LED will flash once indicating a valid key

press. Note: If the button is pressed 21 times it will start back at 0 seconds.

Once this is done press the Normal Flush button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Programming for Tecma Silence (Series) Model Mode 2

Step 1 –Placing the unit in program mode:

After wiring and applying power, hold the Water Only & Empty Only buttons down

together for 3 seconds. The Holding Tank Full LED will give three quick flashes

indicating you have entered program mode. You may now release both buttons.

Once in program mode you can now program one of the following two times: T1 = Water

Inlet / Discharge Pump or T3 = Water Valve/Inlet Pump.

Step 1 will need to be repeated for each of these delay times.

Tecma mode differs as the water inlet and pump discharge times work together:

The pump discharge time will be half (1/2) of the T1 = Water Inlet time (see timing chart

page 6) therefore ONLY T1 & T3 need to be programmed.

Setting T1: Water Inlet / Discharge Pump Time:

After placing the unit in program mode, as in Step 1 above,press the Normal Flush

button the number of times required for the Water Inlet / Discharge Pump time (one

press =1 second, two = 2 sec’s, etc). The Tank LED will flash once indicating a valid key

press. Note: If the button is pressed 21 times it will start back at 1 second.

Once this is done press the Empty Only button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Setting T3: Water Valve/Inlet Pump Time:

After placing the unit in program mode, as in Step 1 above, press the Water Only button

the number of times required for the Water Valve/Inlet Pump time (one press = 0 sec’s,

two = 1 second, three = 2 sec’s, etc). The Tank LED will flash once indicating a valid key

press. Note: If the button is pressed 21 times it will start back at 0 seconds.

Once this is done press the Normal Flush button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Programming for Tecma Prestige (Series) Model Mode 3

There is no programming required for this mode as the times are fixed (see timing chart

page 6).

Programming for European Model Mode 4

Step 1 –Placing the unit in program mode:

After wiring and applying power, hold the Water Only & Empty Only buttons down

together for 3 seconds. The Holding Tank Full LED will give three quick flashes

indicating you have entered program mode. You may now release both buttons.

Once in program mode you can now program one of the following two timers: T1 =

Water Valve/Inlet Pump, T2 = Discharge Pump

Step 1 will need to be repeated for each of these delay times.

Setting T1 Water Valve/Inlet Pump Time:

After placing the unit in program mode, as in Step 1 above,press the Normal Flush

button the number of times required for the Water Valve/Inlet Pump time (one press = 1

second, two = 2 sec’s, etc). The Tank LED will flash once indicating a valid key press.

Note: If the button is pressed 21 times it will start back at 1 second.

Once this is done press the Empty Only button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Setting T2 Discharge Pump Time:

After placing the unit in program mode, as in Step 1 above,press the Empty Only

button the number of times required for the Discharge Pump time (one press = 1 second,

two = 2 sec’s, etc). The Tank LED will flash once indicating a valid key press. Note: If the

button is pressed 21 times it will start back at 1 second.

Once this is done press the Normal Flush button to store this value. The unit will flash

three times indicating the time has been set and you have left program mode.

Model Timing Chart

This device has three different timing sequences, any one may be selected.

(Factory default is Model Mode 2 = Tecma Silence)

Mode 1: Standard Model Mode 1

Model Mode 2: Tecma Silence (Series) -Factory Default

Tecma Single Button Emulation Mode:

Model Mode 3: Tecma Prestige (Series) - Fixed time = 20 seconds

Model Mode 4: European Mode

2 sec’s

Start T1 Water Inlet Off T2 Discharge Motor Off T3 Water Inlet

Programmable

from 1 - 20 sec’s

Programmable

from 1 - 20 sec’s

Programmable

from 0 - 20 sec’s

Start T1 Water Inlet All Off All Off

2 sec’s

Extraction/Motor

Programmable

from1 - 20 sec’s

Programmable

from 0 - 20 sec’s

10 sec’s

Ext/Motor

Water Inlet

4 sec’s

½ of T1

Start

Extraction/Motor

T1 Water Inlet

14 sec’s 18 sec’s 20 sec’s

Start

Extraction/Motor

T1 Water Inlet

Extraction/Motor

will start ½ of T1

Programming the Device for Model Mode or Disable Features

Place the unit in Model Mode / Disable Features Program Mode:

Hold the Water Only & Empty Only buttons down together for 3 seconds. The Holding

Tank Full LED will give three flashes indicating you have entered program mode. While

still holding down these two buttons, press the Normal Flush button. The Tank LED will

give six flashes indicating you have entered Model Mode / Disable Features program

mode, release both buttons.

Selecting Model Mode:

Press the Normal Flush button, the Holding Tank Full LED will give four flashes

indicating you have entered program Model Mode.

You may now select which Model Mode you require: Press the Normal Flush button for

Tecma Silence (Series) (model mode 2), the Empty Only button for Standard Mode

(model mode 1) or the Water Only button for extended models, press the Normal Flush

for Tecma Prestige (Series) (model mode 3) or the Water Only button for European

Mode (model mode 4). The Tank LED will give three flashes indicating you have finished

model program mode.

Disable Features:

You can disable or enable two features:

1/ The Manual buttons. If disabled the only button that will work is the Flush button. The

Water Only and Empty Only buttons will be disabled.

2/ Tank Full. If enabled and the tank is FULL the LED will be turn on and NO

buttons will work. If disabled and the Tank is FULL the LED will be on and ALL

buttons will still work.

3/ Deactivation of the Water Only button after use. If this feature is enabled then after

the Water Only button has been pushed and released it will be deactivated. The Empty

Only button will need to be pressed for at least 1 second to reactivate the Water Only

button. This feature can be disabled or enabled.

Place the unit in Model / Disable Features Program Mode as above (top of page).

Push the Empty Only button, the holding tank full LED will give three flashes indicating

you have entered disable feature mode.

You may now select which feature to disable.

1/ Push the Normal Flush button disable or enable the Tank Full feature.

2/ Push the Water Only button to disable or enable the Manual buttons.

3/ Push the Empty Only button to disable or enable the Water Only button deactivation

feature.

The Tank LED will give three flashes indicating you have finished model program mode.

Repeat the step to re enable these features.

NOTE: The factory default setting is on for both of these features.

Programming Flow Chart

Hold the Water Only &

Empty Only buttons down

together for 3 seconds

(LED will give three flashes)

While still holding down

these two buttons, press the

Normal Flush button

(LED will give six flashes)

Push Normal Flush

For Model.

(LED will give four

flashes)

Push Normal Flush

Tecma Silence Series

Push Water Only

(extended models)

Push Empty Only

Standard Mode

Push Empty Only

For Disable/Enable

features

(LED will give three

flashes)

Push Water Only

Disable/Enable Water

Only & Empty Only

buttons

Push Normal Flush

Tank Full Disable

LED will

give three

flashes and

leave

program

mode

Push Normal Flush

Tecma Prestage Series

Push Water Only

European Mode

Operating Instructions:

Normal Flush:

Pressing the Normal Flush button will run the auto cycle (see page 6 for details).

Water Only:

While this button is held down the water valve/inlet pump will activate (Maximum 20

seconds per press). After activation this button will be disabled. The Empty Only button

will need to be pressed for at least 1 second to reactivate this button. This feature can be

disabled or enabled see page 5.

Empty Only:

While this button is held down the discharge pump will activate (Maximum 20 seconds

per press).

Holding Tank Full: (Optional)

If the vessel is fitted with a Holding Tank Full Sensor Switch, it can be wired to the

controller as per diagram FIG 1 –page 10. If this sensor is on, due to a full tank, it will

disable the controller until the tank has been emptied. If this feature is not required leave

the Float Switch Input unconnected.

Electrical Specifications:

Supply Voltage = 12-30 Volts DC (Auto-sensing)

Quiescent Current = .015 Amps

Input = EMI Protected

Max Motor Output = 44 Amps

Max Valve Output = 44 Amps

Max EST Output = 12 Amps

Connections

FIG 1

Toilet Control

Flush

Tank Full Float Switch

Battery Positive

Battery Negative

Discharge Pump +

EST + (Not used)

Water Inlet Pump/Valve +

Water Inlet Pump/Valve -

Discharge Pump -

GND

Andere Handbücher für STS-220

Inhaltsverzeichnis

Andere Smartswitch Controller Handbücher

Smartswitch

Smartswitch SMF-001 Handbuch

Smartswitch

Smartswitch STS-220 Bedienungsanleitung

Smartswitch

Smartswitch TC-8000 Bedienungsanleitung

Smartswitch

Smartswitch TD-4000 Bedienungsanleitung

Smartswitch

Smartswitch FC-006 Bedienungsanleitung

Smartswitch

Smartswitch NV-2000 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung