Smartwares HA701IP Bedienungsanleitung

FAMILIENHEIM

LUXUSHAUS

GESCHÄFT

BÜRO

HA701IP

smart wireless alarm system

SECURE & MONITOR

FAMILY HOUSE

LUXURY HOME

STORE

OFFICE

Slim line

SURVEILLANCE

Main unit

Motion detector

Door/Window detetctor

Remote

Adaptor & Batteries

Plugs & Screws

Welcome Card

HA701IP

CONTENT

COMPLETE APP CONTROLLED

Manual 10.016.58_HA701IP ---

SMART ALARM SYSTEM

GB SMART ALARM SYSTEM 3 IN 1

* Secure and monitor your home,wherever you are

* Connect directly to internet

* Easy to install, in 12 minutes

* Complete sabotage protected

* Extendable up to 100 accessories/zones

* Receive alarm messages on your smartphone / email

* Automatically, warn your friends or family

* Suitable for home, apartments, small office or shop

* Built-in siren up to 90dB

* Battery backup

* Low battery indicator

* Secure and monitor your home from any computer or smartphone (IOS, Android),

wherever you are!

Frequency : 868.35MHz

Transmission power : <10mW

Transmitting range : Up to 75m (in open space)

Extendable : Up to 100 accessories

Power adaptor : 12V DC, 2A

Backup power : 6x 1,5V DC Battery AA (incl.)

Alarm volume : 90dB/1m

Remote battery : CR2032 type, 3V Lithium (incl.)

Magnetic switch battery : 3V 900mAh Lithium CR2 (incl.)

PIR detector battery : 3V 900mAh Lithium CR2 (incl.)

PIR detection : 110° x 10m

Internet connection : RJ45 LAN - internet cable (incl.)

Operating temperature : -10°C ~ 50°C

Operating

distance 75M

Batteries

included

Easy and Quick

to install

Anti

Jamming

100 accessories

extendable

Welcome to the world of our Smart Home Wireless Alarmsystem HA701IP

We will guide you during the installationtrip; step by step! The trip will start with unpacking, sorting, screwing and

downloading, and will be accompanied by screenshots, so that you see what you get! We wish you a pleasant trip!

Step 1:

Unpack all the products and sort them on the table!

Step 2:

2.1 Write down the Access Code information of the back of the Gateway, on this field of the manual:

The Code is needed for system login.

2.2 Open the battery compartment at the back side and install 6 x 1,5 V AA, close it again.

2.3 Plug in the internet (LAN) cable and the adaptor (POWER) in the contacts at the back.

2.4 Plug the other side of the internetcable in your router, and the adaptor in a powersocket.

Step 3:

Remove the insulating films on the back of the Motion Sensor and Magnetic Contact Sensor. Remove the insulating

films on the side of remote.

2.1

2.3

2.4

2.2

Step 4:

Open on your computer again: www.mysecurity.smartwares.eu Click on "CREATE A NEW ACCOUNT"

Step 5:

Click on "CREATE A NEW ACCOUNT"

Step 6:

Confirm your country. Fill in your email adress which will also be your accountname. Fill in the password you want

to use for this account. Confirm the password. Click on Submit

Step 7:

You are now in System Registration:

a gateway is found on your network!

Fill in the code and click on NEXT STEP

Step 8:

The system will congratulate you, and askes which name you want to give your system.

Step 9:

The software of you system aske for a update; click on "START UPGRADE"

Congratulations: Your system is connected and up to date: Click on "TERMINATE"

Step 10:

You are in the main menu of the system!

Step 11:

Connect and check the Motion Sensor, Magnetic Sensor and Remote! Click on "System"

Step 12:

We will now add the Sensors and the Remote!Click on "+ add a new device"

Step 13:

Select the device you want to add, for example Remote, and click on it.Not all device you see now

are already available! Some are under development

Step 14:

Now you push on one of the buttons of the remote within the count down time!

Step 15:

You will get a confirmation that it is learned success full. When it is already connected, you will get the message that it is

already known. Now you do the same for the Motion Sensor and the Magnetic Contact Sensor.

All connected devices are shown in the screen. The main Unit is called Internal Siren

Step 16:

Decide where you want to mount you main unit! We advice to mount it out of sight, so that in case of burglary it wil not

easy be found! You need to connect the internet (LAN) cable and plug in the adaptor! Use the template paper to mark

the positions of the screws on the wall. Leave the screw head protruding for about 7mm so it can push the tamper switch

(on the back of the Gateway) into place.

Step 17:

Install Motion Sensors and Magnetic Contact Sensors on the place you think they are the most effective! Montion Sensors

secure a complete Area of 110° x 10 meter. Install in the rooms which are attractive fur the burglar a Motion Sensor.

Don't point the Sensor to windows or heathers! When a Motion Sensor registers Motion it will give a signal to the main

unit. Magnetic Contact Sensors secures one door or window. Install on the doors or windows which are interesting for the

burglar a Magnetic Contact Sensor. When a door or window is opened, it will give a signal to the main unit.

Advice:

We advice to make a drawing of your home and mark the burglary

sensitive points with a red arrow! When you have done

this you are going to fill in where you want to install motion- and magnetic sensors! When you have filled in all sensors,

you mark

them if you want them active at night, or only when you are out. We advise to

install also minimum a indoor

siren, on a strategic place. I case of burglary

everybody in the house must be warned. Depending on the neighbour-hood it

also wise to install a outdoor siren! They are all wireless, so easy to install. If you

live with more persons in one house, or

doesn't like to take the remote, or open

the app everytime to activate or deactivate the system, then we advice to add a

keypad! You can give per person a code, so you can always see who activated or

deactivated the system! For total security

of your home you also can add; smoke-

and waterdetectors and a connected to your alarmsystem Internet camera!

important:

The PIR/Motion sensor has a battery saving mode! This means that

the Motion Sensor is always ready for triggering. And it

will always send a signal

to the main unit after it is triggered! After the Motion sensor is triggered, and

the alarmsystem is

on, the siren will go for 3 minutes! The Motion Sensor will

get in "safe battery - mode" for 3 minutes, and will react again

when it is

triggered after 3 minutes! ALSO IN TEST MODE YOU HAVE TO WAIT 3 MINUTES

AFTER EVERY TRIGGER!

Step 18:

Personalising the System Settings; click on "Systems"

Laundry

Hall

Legend

P.I.R. Detector

Magnetic Switch

Keypad

Indoor Siren

Outdoor Siren

Smoke Detector

Water Detector

Bedroom

Bathroom

Bedroom

Livingroom

Kitchen

Study

Bedroom

Bathroom

Walk in closet

Sauna

Storage

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smartwares Sicherheitssystem Handbücher

Smartwares

Smartwares DVR620S Bedienungsanleitung

Smartwares

Smartwares SA68G Bedienungsanleitung

Smartwares

Smartwares HomeWizard Connect Kit Bedienungsanleitung

Smartwares

Smartwares HA32S Bedienungsanleitung

Smartwares

Smartwares HA788GSM Bedienungsanleitung

Smartwares

Smartwares DVR640S Bedienungsanleitung

Smartwares

Smartwares SMA-40252 Bedienungsanleitung

Smartwares

Smartwares FGA-13900 Bedienungsanleitung

Smartwares

Smartwares HA788GSM Bedienungsanleitung

Smartwares

Smartwares SMA-40252 Bedienungsanleitung

Smartwares

Smartwares CS96DVR Service-Handbuch

Smartwares

Smartwares FWA-1821 Bedienungsanleitung

Smartwares

Smartwares SC88 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung