SMARTWINGS WR01-15CH Bedienungsanleitung
WR01-15CH Remote Programming Guide
SMARTWINGS MOTORIZATION
SMARTWINGS
Table of Contents
1. Remote Overview
2. Sleep Mode
3. Adjusting Limits
4. Favorite Positions
5. Remote & Motor Pairing
6. Mirroring Remotes
7. Group Control
8. Hiding/Unhiding Remote
Channels
9. Adjusting Motor Speed
10. Reset to Factory Settings
11. Initial Setup Programming
12. Reverse Motor Direction
13. Tilt Mode
Each battery motor from Smartwings will come preprogramed from the factory. The
preprograming ensures the remote is paired with the motor, the upper and lower operation
limits are set, the remote is unlocked
.
1 .
1 .
Motor P B F
Recharge the battery
Troubleshooting
Remote Overview
FEATURES
• Push Button controls
LED Display
Hide unused channels function
wall mount holder
•
•
•
•
PACKAGE CONTENTS
Remote
wall mount holder & fixing screws
1.5V - AAA Battery
TECHNICAL SPECIFICATIONS
Voltage: 3V
Frequency: 433.92 MHz
Transmitting Power: 30 milliwatt
Ambient Operating
Temperature: - -
Transmission Distance: Approx. 65 feet in
open space
Battery: AAA
FRONT BACK
Each battery motor will come preprogramed from Smartwings Upon leaving the factory the
motor
is
placed into “Sleep Mode” to avoid accidental operation during shipping. It is necessary to “Wake”
the
motor before operation and setup.
Sleep Mode
To “Wake” the motor and exit Sleep Mode, assure the motor is installed and secured in the
mounting hardware.
Once installed safely and securely, press and hold the programming button on the motor head
until the motor jogs once. It is now no longer in “Sleep Mode” and ready for further setup.
Warning:
•Shade - if you press and release the programming button quickly, the motor will operate to its
limit.
•
If required, to place the motor back into “Sleep Mode” press and hold the programming button
for a period of 10 seconds. Release the button when the motor has jogged three times. The “
Sleep Mode” has been activated.
Exit Sleep Mode
Enter Sleep Mode
Adjusting Limits
Each battery motor will come preprogramed from Smartwings .
The preprograming ensures the remote is paired with the motor, the upper and lower operation limits
are set, the remote is unlocked .
Follow the below steps to adjust the upper and lower limits if required.
Press UP & STOP (5sec) Press UP + STOP (2sec)
(SET Top Limit)
ADJUSTING LOWER LIMIT
ADJUSTING UPPER LIMIT
Move the shade to the new desired
position to be set as limit.
Press DOWN & STOP (5sec) Press DOWN + STOP (2sec)
(SET Lower Limit)
If limits need adjusting, follow the instructions
below to unlock the remote for limit setting:
!!WARNING!! - Move shade in short increments by pressing the UP/DOWN button in 1 second intervals (pressing the
UP/DOWN button for more than 3 seconds may send the shade past desired upper/lower limit and may result in
damage to the product). Once you have reached the desired upper/lower limit, you can adjust the limit with either the
UP and DOWN buttons. (remember to adjust in short increments!)
Important!! Stop the shade prior to
traveling past the desired upper limit
Important!! Stop the shade prior to
traveling past the desired lower limit
Note: the motor jogs once
Note: the motor jogs once
Note: the motor jogs twice
Note: the motor jogs twice
Move the shade to the new desired
position to be set as limit.
+ +
+ +
Favorite Positions
Each battery motor will come preprogramed from Smartwings .
The preprograming ensures the remote is paired with the motor, the upper and lower operation limits
are set, the remote is unlocked.
Follow the below steps to set a favorite position. The favorite position is used to set a custom stopping
point between the upper and lower limits. (1 favorite position per shade motor)
To set a favorite position for a shade motor, drive to the desired position and press the STOP
button to pause the drive operation.
Press P (1sec)
1(To Save Position)
Press UP or DOWN
to move shade to
desired favorite position
position
SETTING FAVORITE POSITION
3
2
•Press STOP (2sec) to move shade to the Favorite Position from any location
Repeat Steps 1-4 for all additional motors•
Press STOP (1sec)
DELETING FAVORITE POSIT ION
the shade is
1 (To Delete Position)
Note: the motor jogs twice
Note: the motor jogs once
Note: the motor jogs once
4Press STOP (1sec)
Press P (1sec) 3
2Press STOP (1sec)
Note: the motor jogs once
Note: the motor jogs once
Note: the motor jogs once
Press STOP (1sec)
4
Remote + Motor Pairing
Each battery motor will come preprogramed from Smartwings .
The preprograming ensures the remote is paired with the motor, the upper and lower operation limits
are set, the remote is unlocked.
Follow the below steps to select the remote channel you want to pair with the motor(s) if required at a
later date.
Press any
button to
wake remote
Within 10sec Press
" " or " " to
select desired
channel.
1a 1b
1. SELECT CHANNEL
Within 10 sec of
activating pairing mode,
Press & Hold STOP
If you do not pair the remote in time the motor pairing sequence will time out, repeat the
above steps assuring to press and hold the STOP button within 10 seconds of the motor jog
2. PAIRING REMOTE TO MOTOR
Press & HOLD
Programming Button
on motor head (2sec)
2a ACTIVATE PAIRING MODE ON MOTOR
2b ADDING OR REMOVING THE REMOTE
Note: the motor jogs once
Note: the motor jogs twice.
Press STOP (2sec)
Mirroring Remotes
Each battery motor will come preprogramed from Smartwings .
The preprograming ensures the remote is paired with the motor, the upper and lower operation limits
are set, the remote is unlocked.
Follow the below steps to copy settings from an existing remote to a new remote.
2. ADD OR REMOVE REMOTE USING AN EXISTING REMOTE
1Press P (1sec)
EXISTING
2Press P (1sec)
EXISTING
3Press P (1sec)
NEW
(To be Added or Removed)
Note: Select channel on existing remote to be copied
Select channel on new remote where existing channel will be copied
Note: the motor jogs once Note: the motor jogs twice
Note: the motor jogs once
Press any
button to
wake remote
Within 10sec Press
select desired
channel.
1a 1b
1. SELECT CHANNEL
" " or " " to
Group Control
Each battery motor will come preprogramed from Smartwings . If multiple motors are
paired to the same 15 channel remote, the 0 channel is the default channel to control all motors at once.
Follow the steps below to group motors on a specific channel for simultaneous control.
To custom define a channel to control multiple motors, pairing in groups can be executed. This will
allow you to operate a series of motors in unison without needing to change channels. Each motor to be
grouped must be paired with the remote on its own channel prior to grouping.
1. SELECT CHANNEL TO BE PAIRED AS A GROUP
2. PAIRING OR REMOVING MOTOR FROM A SPECIFIC CHANNEL
Within 10 sec of
activating pairing mode,
Press & Hold STOP
If you do not pair the remote in time the motor pairing sequence will time out, repeat the
above steps assuring to press and the STOP button within 10 seconds of the motor jog
2a ACTIVATE PAIRING MODE ON MOTOR
2b PAIRING REMOTE
Press any
button to
wake remote
Within 10sec Press
select desired
channel.
1a 1b
Press & HOLD
Programming Button
on motor head (2sec)
Note: the motor jogs once
Note: the motor jogs twice.
Press STOP (2sec)
" " or " " to
Inhaltsverzeichnis
