Smarty BX4000 Bedienungsanleitung
USER GUIDE
Model: BX4000
Thank you for purchasing this Drive Recorder.
Before using the Drive Recorder, please ensure that you
read and understand this USER GUIDE.
Please store the USER GUIDE in an easily accessible location.
Before connecting and installing this Drive Recorder, please
refer to the appropriate instruction manual for proper operation.
VER 2.0.1
3
FCC
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one more of the
following measures:
-Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Caution
Damages due to production malfunction, loss of data, or other damages occurring while
using this product shall not be the responsibility of the manufacturer. Although the
product is a device used for recording videos, the product may not save all videos in the
case of a malfunction. In the case of an accident, the sensor may not recognize the
shock when the impact is light and as a result it may not begin recording automatically.
SAFETY ADVICE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Caution
Install the product where it does not block driver’s visibility
and where there is no airbag installed. This could cause an
accident or might injure the passengers in case of accident.
Please make sure you follow the safety advice/instructions given in the user guide.
4
Caution
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Battery for RTC(Real Time Clock) inside
Caution
When the impact is light like very light, such as a minor bump in the road,
the G-sensor may not recognize the impact and as a result it may not begin
recording automatically. Test and set your own G-sensor level for your vehicle.
GPS Reception
1. Activate the product in an area without large buildings
to improve GPS reception.
2. The temperature range for optimum operation of the GP
S receiver in your car is -10 ~ 50°C.
3. When using the product for the first time or after a long
period (more than three days), it may take a little longer
to recognize your current location.
It may take between five and thirty minutes to get GPS reception.
GPS reception may be impaired under the following circumstances.
1) If there is an object at the end of the GPS antenna
2) If your vehicle has metallic elements on the windshields
3) If equipment generating electromagnetic waves that interfere with the GPS
signal is installed in the vehicle e.g.: Other GPS devices such as a certain
type of wireless activated alarms, MP3 and CD players and camera alarms
using GPS.
4) If you are using a receiver connected by cable, electric interference can be
avoided by simply changing the location of the receiver (antenna).
5) On heavily overcast or cloudy days, if the vehicle is in a covered location
such as under a bridge or raised roadway, in a tunnel, an underground
roadway or parking area, inside a building or surrounded by high-rise
buildings.
6) If GPS signal reception is poor, it may take longer to locate your current
position when the vehicle is moving than when it is stationary.
5
The commercial purpose GPS has the average rage error of more
than 15 meters and the range error could be more than 100 meters
due to environmental conditions like buildings, roadside trees etc.
CONTENTS
1. Smarty BX4000 unit
2. 4GB SD memory card
(The PC Viewer software is
on the provided SD card.)
6
You should have a set of the following items with each BX4000 order.
3. GPS Antenna module
4. Remote Controller
5. Audio/Video output cable
6. Power Cable
8. Wire Splice clip (5pcs)
7. Camera input cable
9. Sticker (double sided tape 1pc)
10. Velcro Sticker (1pc)
INTRODUCTION
FRONT
REAR
7
SD Slot
SD Door
Audio/Video
Output
External MIC input
BUZZER
Internal Microphone
Camera 1, 2 Input
Remote Control Input
GPS Input Power Input
&
Alarm (Car Signal)
Input
(Turn left, Turn right,
Brake, Speed pulse)
Rear View
Camera 4 Input
Camera 3
Input
INTODUCTION
REMOTE CONTROLLER
8
Record LED
BLUE LED
Overwrite LED
RED LED
SHUTTER BUTTON
PLAY BUTTON
PANIC BUTTON
Audio Video Output Cable
Video out 1 Video out 2
Audio out 1
[Note] The same screen will be shown through the Video out 1 & 2.
9
INTODUCTION
Power & Car Signal Input
FUSE
250V 3A
Red(+)
Black (Ground)
BLUE (Alarm1)
Yellow (Alarm3)
White (Speed pulse)
Green (Alarm2)
FUNCTION (MAIN UNIT)
Automatic start
Make sure that peripherals, including cameras, are properly connected.
Turn on the vehicle power, BX4000 will automatically start. (Use the power
cable provided.)
Event recording
The Event recording will be started automatically by Motion detection, Alarm1,
Alarm 2, Alarm 3, and/or by the G-sensor level.
The emergency recording can be activated by pressing the [PANIC] button.
10
Notice : The unit will not start recording immediately after the power is
turned on. It takes up to 1 minute for the built-in power backup system
to charge. Thereafter, the internal flash memory will be ready to record.
Normal recording (Continuous record)
The Normal (continuous) recording will be automatically started after power up.
BX4000 will not make a separate event file during the continuous recording.
It will mark or “flag” the Event area as ‘Alarm1~3’, G-senor, Motion detection or
[PANIC] button in the continuous recording file, which can be easily searched for
during playback. The alarms can also be displayed on the video image.
Live image on LCD Monitor
BX4000 will display the live video image on the LCD monitor.
The camera channel can be changed using the information on the OSD.
(Refer to page 13)
Playback in the car
Recorded files can be played back in the car using LCD monitor and remote.
PC Viewer Software
The software is pre-loaded on the SD card in the “pcsw” folder.
Combination recording (Event & Normal record)
If you set different record modes per camera, i.e camera1 set as Event record
and camera 2 set as Normal record, then camera1(Event record) will work
according to the record setting for example 10 frames per second recording.
However camera2 (Normal record) will record 1frame per second, if there is no
event. If there is an Event, both cameras will record according to the record
setting for example 10 frames per second recording.
Andere Handbücher für BX4000
2
Inhaltsverzeichnis
Andere Smarty Dashcam Handbücher
