SMC Networks IP8100-0 1 X83 Series Bedienungsanleitung

ＯｐｅｒａｔｉｏｎＭａｎｕａｌ

Document No.：IP80-OM00006-B

ELECTRO-PNEUMATIC POSITIONER

IP8100-0*1-*-X83

IP8100-0*1-*-X84

WITH OUTPUT CURRENT(4～20mADC)

SMC CORPORATION

Wiring and zero point / span adjusting of output

current of IP８100 type electro-pneumatic positioner

output signal specification (potentiometer built-in)

This product is IP8100 having potentiometer and the P.C.board built in it. It is for

ensuring actuator’s opening by 4～20mADC of output signal produced by supplying

power to it.

Supplying power can be set freely between DC12～35V.

1.Wiring of input signal , power source and ammeter

Connect input signal(for positioner control) to 1(+) and 2(－) of the terminal board.

Connect power source(for detecting output current) to 3(+) and 4(－) of the terminal

board.

Connect ammeter in series between (+)side and 3(+) of terminal board or (－)side and

4(－).

Please refer Fig.1 for wiring.

Fig1Wiringdiagram

NOTE

Allowable load resistance in drawing 1 depends on supply voltage

Allowable load resistance is obtained by the formula below.

Allowable load resistance ≦(Supply voltage －12V) ／20mADC －（１）

Normal output current is not be obtained if the load resistance value exceed the result

of formula(1). Please confirm internal resistance when selecting ammeter.

－1－

2.Zero・Span adjusting

This product requires zero・span adjustment of output current according to actuator’s

opening (rotating angle).

Please follow steps below.

① Set actuator’s output opening 0% after adjusting the zero・span.

② Output signal is connected to rise in normal operation(clockwise) when shipped.

To apply the positioner in reverse operation(counter-clockwise), swap terminal

″A″and″C″in Fig.2.

③ Loosen potentiometer set screws applying power and ensuring output current, then

rotate the potentiometer 10°～20°away from dead band (see Fig.3) to decide the

start point. Settle the potentiometer with the screws again(Refer ″Cautions ″！)

④ Adjust zero・span with variable resistor.

Adjust zero point and span alternately repeatedly as they act each other. Since this

variable resistor can be wound endlessly, do not overwind otherwise internal

equipment might be broken. Adjust them ensuring output signal.

Cautions(settling potentiometer)

(1) Output signal dose not go at the dead band of the potentiometer

(2) If set the start point(4mADC) at the border line of resistance portion and the

dead band, malfunction might be occurred.

(3) If output current is 0mADC during opening, the potentiometer is possibly used

across the border between the resistance and the dead band. Follow③of section 2

ensuring potentiometer rotating direction.

(4) When the positioner is used in reverse action, adjust the potentiometer fixing

position to avoid interpretation between cam and lead wire of the potentiometer.

Fig2.P.C.board

ＡBC

Ａ

－2－

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SMC Networks Ventilstellungsregler Handbücher

SMC Networks

SMC Networks IP8000-0 Series Bedienungsanleitung

SMC Networks

SMC Networks IP8000 Bedienungsanleitung

SMC Networks

SMC Networks IP8101 Series Bedienungsanleitung

SMC Networks

SMC Networks KQ2 Series Bedienungsanleitung

SMC Networks

SMC Networks Chryssafidis P8001 Series Handbuch

SMC Networks

SMC Networks IP8000 Handbuch

SMC Networks

SMC Networks IP6000 Bedienungsanleitung

SMC Networks

SMC Networks IP8000-0 Series Handbuch

SMC Networks

SMC Networks IP8001 Series Bedienungsanleitung

SMC Networks

SMC Networks IP6000 Handbuch

Beliebte Ventilstellungsregler Handbücher anderer Marken

Parker

Parker 404XE Series Bedienungsanleitung

Ytc

Ytc TMP-3000 Bedienungsanleitung

PI M-605 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PXV100AS-F200-SSI-V19 Bedienungsanleitung

RTK

RTK RE 3442 Series Bedienungsanleitung

CVS Controls

CVS Controls 1200 Bedienungsanleitung

Parker

Parker MX80L series Bedienungsanleitung

Westlock

Westlock Quantum 2800 Handbuch

Samson

Samson 3730-0 Service-Handbuch

Samson

Samson TROVIS 3730-3 Service-Handbuch

ESCO Technologies

ESCO Technologies ETS LINDGREN 2302-001 Bedienungsanleitung

Samson

Samson FOUNDATION 3730-5 Service-Handbuch

Samson

Samson TROVIS SAFE 3731-3 Service-Handbuch

Flowserve

Flowserve Logix 3400MD Bedienungsanleitung

halstrup-walcher

halstrup-walcher HIPERDRIVE Bedienungsanleitung

ABB

ABB TZIDC Schulungshandbuch

Samson

Samson FOUNDATION 3730-5 Service-Handbuch

halstrup-walcher

halstrup-walcher PS*3**DP series Bedienungsanleitung