Smeg Freestanding Gas Range C6GGXU Bedienungsanleitung

Important Safety Instruction

IMPORTANT SAFETY INSTRUCTIONS

WARNING: If the instructions contained in this manual are not followed

precisely, fire or explosion may result causing property damage, personal

injury or loss of life.

- Do not store or use gasoline or other flammable vapors or liquids near this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switches.

• Do not use any telephones in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

• lf you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service

agency or gas supplier.

READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important.

We have provided many important safety messages throughout this manual and on the appliance.

Read all the instructions before using the appliance and always obey all safety messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can result in severe

personal injury or loss of life.

UNDERSTAND SIGNAL WORDS

A signal word – DANGER, WARNING, or CAUTION – is used with the safety alert symbol. DANGER

denotes the most serious hazards. It means you could lose your life or be seriously injured if you do not

immediately follow the instructions. WARNING means you could lose your life or be seriously injured if

the instructions are not followed. CAUTION indicates a potentially hazardous situation which, if not

avoided, could result in minor to moderate injury.

Important Safety Instruction

The safety messages will inform you of potential hazards, on how to avoid the risk of injury and what can

occur if the instructions are not followed.

IMPORTANT: Observe all governing codes and ordinances.

WARNING: For your safety, the instructions contained in this manual must be followed to

minimize the risk of fire or explosion and to prevent property damage, personal injury or loss of

life.

- This conversion kit must be installed by a qualified service agency in accordance with the

manufacturer's instructions and all applicable codes and requirements of the authority

having jurisdiction.

- The qualified service agency is responsible for the proper installation of this kit.

- Installation shall not be considered correct and complete until the operation of the converted

appliance is checked as specified in the manufacturer's instructions supplied with this kit.

WARNING

FIRE HAZARD

Securely tighten all gas connections. lf connected to LP, have a qualified

technician ensure that the gas pressure does not exceed a 14" W.C.P.

Examples of qualified technicians include licensed heating personnel,

authorized gas company personnel and authorized service personnel.

FAILURE TO DO SO CAN RESULT IN LOSS OF LIFE, EXPLOSION, OR FIRE.

Conversion Kit

Check that the main gas supply line to the range is shut off and that the

power supply cord is disconnected.

Remove access cap “A” by using a screwdriver or a coin, turning the access cap counterclockwise.

The gas pressure regulator has two settings which are indicated on two sides of the cap. Turn the cap

and reinstall it in the regulator with "LP" visible from the outside of the regulator.

Incoming line pressure upstream

from the regulator must be 1” (2.5

cm) W.C.P. higher than the manifold

pressure in order to check the

regulator. Incoming line pressure to

the regulator should be as follows for

operation and checking the regulator

setting: - NATURAL GAS:

Set pressure to 4” W.C.P. Incoming

line pressure of 3 1/2” - 10 1/2” W.C.P

maximum; - LP GAS: Set pressure

to 11” W.C.P. Incoming line pressure

8”- 13” W.C.P. maximum.

The range must be isolated from the gas supply piping system by turning off the respective manual shut-

off valve during any pressure testing of the gas supply piping system at test pressures equal to or

greater than 1/2 psig (3.5 kPa).

Replacing the rangetop's burners nozzles (This operation does not require primary air regulation.)

1 Remove the grates and all the burner caps and

heads;

2 Unscrew the burner nozzles with a 7 mm socket

wrench;

3 Replace the nozzles according to the type of gas to

be used and the description in paragraph 3.2

“Burner and nozzle characteristics table”.

Put the burners back in their correct position.

Conversion Kit

Replacing the oven's burners nozzles (This operation does not require primary air regulation.)

Oven burner

1 Open the oven door

and remove any

accessories that are

inside.

2 For 35” - 908mm model

unscrew the two

fastening screws before

removing the oven floor. 1) 2)

3 Lift the oven floor and

slide it out.

4 Unscrew the burner's

fastening screw.

3) 4)

5 Remove the burner

from its place by sliding

it out and moving it to

the side. (Make sure

not to damage the

thermocouple or the

spark electrode during

this operation).

6 Using a 7mm socket

wrench replace the

nozzle installing the

one that is appropriate

for the type of gas to be

used. Refer to the gas

charts at point 5.

5) 6)

7 WARNING: The

tightening torque of the

nozzle must be equal to

4Nm.

8 After replacing the

nozzle, put the burner

back in its place. (Make

sure not to damage the

thermocouple or the

spark electrode during

this operation).

7) 8)

Conversion Kit

9 Screw in the burner's

fastening screw.

10 Reposition the oven

floor making sure to

insert it correctly. The

floor must be perfectly

level.

9) 10)

11 For the 35” - 908mm

model screw the two

fastening screws after

having repositioned the

oven floor.

11)

Broil burner

1 Unscrew the burner's

fastening screw.

2 Remove the burner by

sliding it from its place

and reposition it as shown

in the picture. (Make sure

not to damage the

thermocouples and the

spark electrode).

1) 2)

3 Using a 13mm socket

wrench replace the

nozzle installing the

one that is appropriate

for the type of gas to be

used. Refer to the gas

charts at point 4.

4 WARNING: The

tightening torque of the

nozzle must be equal to

4Nm - 14.4 Ozf.

3) 4)

5 Reposition correctly the

burner in its place and

screw in the fastening

screw.

Conversion Kit

5) To adjust the range for LP gas or to return to Natural Gas use, refer to the charts below.

C6GGXU (23 15/16” - 608 mm)

Natural gas

Qt Injector Qr

BTU Ø mm BTU

Front Right 6200 1.20 1500

Front Left 6200 1.20 1500

Rear Left 3400 0.90 1200

Rear

right

Outer 12000 1.17 (n.2) 4000

Inner 3000 0.85 1200

Oven 11200 1.60 3400

Broiler 10500 1.55 4100

Qt Injector Qr by-pass

BTU Ø mm BTU mm

Front Right 6200 0.72 1500 0.39

Front Left 6200 0.72 1500 0.39

Rear Left 3400 0.54 1200 0.33

Rear

right

Outer 12000 0.70 (n.2) 4000 0.65

Inner 3000 0.50 1200 0.33

Oven 11200 0.96 3400 0.55

Broiler 10500 0.92 4100 0.59

NOTE: Save the nozzles removed from the appliance for future use.

Rear left

Front left Front right

Rear right

Outer

Inner

Conversion Kit

C9GGXU (35 3/4” - 908 mm)

Natural gas

Qt Injector Qr

BTU Ø mm BTU

Front Right 6200 1.20 1500

Front central 3400 0.90 1200

Front Left 6200 1.20 1500

Rear Left 3400 0.90 1200

Rear

center

Outer 12000 1.17 (n.2) 4000

Inner 3000 0.85 1200

Rear right 10000 1.52 2500

Oven 18000 2.10 5300

Broiler 19000 2.15 5800

Qt Injector Qr by-pass

BTU Ø mm BTU mm

Front Right 6200 0.72 1500 0.39

Front Center 3400 0.54 1200 0.33

Front Left 6200 0.72 1500 0.39

Rear Left 3400 0.54 1200 0.33

Rear

center

Outer 12000 0.70 (n.2) 4000 0.65

Inner 3000 0.50 1200 0.33

Rear right 10000 0.90 2500 0.45

Oven 18000 1.20 5300 0.72

Broiler 19000 1.25 5800 0.76

NOTE: Save the nozzles removed from the appliance for future use.

Rear left

Front left Front

center

Rear

center Rear right

Front right

Outer

Inner

Conversion Kit

WARNING

FIRE HAZARD

- Use a soapy solution to check that it is leak-tight.

- Never test for gas leaks with a match or other flames.

- Failure to follow this instruction can result in loss of life or

fire

Follow these instructions to leak test the appliance:

Use a brush and liquid detergent to test all gas connections for leaks. Bubbles around connections

indicate a leak. If a leak appears, shut off gas valve controls and adjust connections. Then check the

connections again.

NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAMES.

Remove all the detergent product from the range.

Replace the parts on the burner and turn the knobs on the gas tap pins.

Light the burner and set it at minumum . Remove the knob and turn the adjustment screw next to the

gas tap pin until you obtain a suitable minimum flame. Replace the knob and check flame stability by

rapidly turning the knob from maximum to minimum. The flame should not go out.

8) Check the flame at the maximum flame position for a blue color. It should be clean and soft in

character. No blowing or lifting of flame should occur. Occasional orange flashes are normal and reflect

different elements in the air or gas.

9) Completely fill out the conversion label (part no. 92849A078) and attach the label in the storage

compartment beside the ID tag. Do not cover the ID tag with the conversion label.

10) At higher altitudes, no further adjustments are necessary. Derating the burners is also unnecessary.

11) Save the nozzles removed from the unit along with these instructions for possible future use.

NATURAL GAS:

To convert back to Natural Gas: Follow steps 1 through 11 and replace the nozzles in the order in which

they were removed.

Andere Handbücher für Freestanding Gas Range C6GGXU

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smeg Kochfeld Handbücher

Smeg

Smeg SA611XA Bedienungsanleitung

Smeg

Smeg SAI63 Bedienungsanleitung

Smeg

Smeg SE32CX Technisches Handbuch

Smeg

Smeg PU64 Bedienungsanleitung

Smeg

Smeg SIHP264S Bedienungsanleitung

Smeg

Smeg PGA75F-4 Bedienungsanleitung

Smeg

Smeg SI4642D Bedienungsanleitung

Smeg

Smeg PX1402AU Bedienungsanleitung

Smeg

Smeg Portofino Bedienungsanleitung

Smeg

Smeg RTU366GX Bedienungsanleitung

Smeg

Smeg NCT 335 E Bedienungsanleitung

Smeg

Smeg SE264ID Benutzerhandbuch

Smeg

Smeg GCO90XG Bedienungsanleitung

Smeg

Smeg SUK62CMX5 Bedienungsanleitung

Smeg

Smeg PU64ES Bedienungsanleitung

Smeg

Smeg PGF75SCU3 Bedienungsanleitung

Smeg

Smeg PBQ31GA Bedienungsanleitung

Smeg

Smeg SIHP263B Bedienungsanleitung

Smeg

Smeg SEU122B Bedienungsanleitung

Smeg

Smeg CIR60X Bedienungsanleitung

Smeg

Smeg SI5633 Bedienungsanleitung

Smeg

Smeg NCT335EEU Konfigurationshandbuch

Smeg

Smeg A41 Bedienungsanleitung

Smeg

Smeg SI5644B Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung

Jenn-Air

Jenn-Air CCE1400 Bedienungsanleitung